2008 suburban wipers slow and stop

You search PDF repair manual about 2008 suburban wipers slow and stop, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 suburban wipers slow and stop Direct Download speed 5432 Kb/s

  2008 suburban wipers slow and stop Full Version speed 8172 Kb/s



GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, 2008 checrolet colorodo emmisions purge valve, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 pilot alternator replacement, how to change the thermostat 2008 ford escape ehow, inhrdvd1000 parts, 2008 saturn outlook transmission pressure solenoid, hummer h3 2008 p0741, 2008 f250 haynes pdf

Windshield Wiper Linkage Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
Installation Instructions 1. Place the Wiper Motor Mount Plate (FFR# 25391) along the edge of the ¾” shock tower support tube on the passenger side and the top of the footbox front wall aluminum. Mark the location for the riv nuts (4 total). 2. Drill the riv nut holes using a 25/64″ drill bit. You may want to begin by using a smaller drill bit to drill a pilot hole first (shown). 3 3. Intsall the 1/4″ riv nuts (4) using the supplied riv nut tool. 4. Install one of the rod ends (FFR# 25724) with the supplied jam nut (FFR# 25725) onto the wiper motor arm (1/2″, 9/16″ wrenches). You will have to trim some of the excess thread off of the rod end in order for it to have sufficient clearance between it and the wiper motor mount plate. 4 5. Place the wiper motor in the mount plate (FFR# 25391) so the pins on the motor fit inside the holes in the mount plate and the three threaded holes in the motor line up with the corresponding holes in the mount plate. 6. Using the three Corvette screws that held the motor in place, fasten the motor to the mount plate (T- 30 Torx). 7. Place a nylon spacer (FFR# 10960) between the frame and the mount plate at each of the riv nuts and bolt the plate into positon using the supplied ¼”-20 x 1.5″ long bolts (4mm allen).
6 ATTENTION: For the bolt at the front corner of the plate, you may have to use the supplied washers as well as the nylon spacer to prevent the bolt from bottoming out before the plate is firmly in place (See photo). 8. Screw the supplied section of threaded rod (FFR# 25723) into the rod end on the wiper motor. 7 9. Slide the aluminum tube (FFR# 25934) over the threaded rod and measure how much of the aluminum tube will need to be trimmed once the rod end is screwed on. Trim the tubing with a tubing cutter/hacksaw/cutoff wheel. 10. As you did with the rod end on the wiper motor, you will have to trim the threads on the rod end to clear the aluminum. 11. Place the aluminum tube over the threaded rod, then screw the rod end (FFR# 25724) onto the rod until tight. 12. Before installing the wheel box to the body you will have to trial fit the wiper arm to the wheel box. It is a tight fit, so you may have to spray the splines with some WD-40 or some oil and tap the wiper arm onto the splines. Remove the wiper arm from the wheelbox so you can bolt it to the body. 8 13. Follow the instructions in the assembly manual for bolting the wheelbox to the body. 14. Install the rod end on the wiper wheel box arm with the supplied jam nut (FFR# 25725) (1/2″, 9/16″ wrenches). 15. Install the wiper blade (FFR# 25629) onto the wiper arm (FFR# 25552). 16. Clip the wiper arm onto the shaft of the wiper wheel box, making sure that the tab on the arm clips into the channel on the wheel box shaft (clip shown). 9 17. Spray the windshield with water, or glass cleaner. Check the sweep by turning the wipers on – start with the slowest setting to avoid damaging the linkage or running the wiper beyond the windshield. Make any necessary adjustments, and the linkage installation is complete

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage

1992 Cadillac Deville 4.9L Windshield Wiper Blade and Arm REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Cadillac Manuals) by admin on 22-05-2011

download
REMOVAL & INSTALLATION Catera Open the hood. 1. Remove the windshield wiper arm stud cap that conceals the nut. 2. Remove the windshield wiper arm nut. 3. Grasp the windshield wiper arm with both hands. 4. Use a rocking motion to loosen the windshield wiper arm from the pivots. 5. Remove the windshield wiper arm and blade. 6. To install: Installation is the reversal of the removal procedure. 7. Deville and Fleetwood WIPER ARM Raise the hood as needed for access to the wiper arms. 1. Operate the wipers and turn the ignition OFF when the wipers are at the mid-wipe position. 2. Lift the wiper arm from the windshield. 3. On 1990 vehicles, pull the retaining latch and remove the arm from the transmission shaft. 4. On 1991-93 vehicles, disengage the retaining latch using a suitable tool and remove the arm from the transmission shaft. 5. To install: Install the wiper arm onto the transmission shaft. 6. Push the retaining latch in and return the arm assembly to the windshield. 7. Park the wipers. If adjustment is necessary, proceed as follows: Remove the right wiper arm. a. Open the small door to access the wiper linkage; refer to the illustration for details. b.

Related Content:

1992 cadillac seville manual free download, how to remove wiper arm assembly chevy impala recalls, 1992 Cadillac Deville Owners Manual, 2007 chevy tahoe rear windshield wiper arm remove, cad 1992 seville horn low volume ?, how to replace a windshield wiper motor on a 2004 impala, remove wiper arm 04 ompala, video of how to install a windshield wiper arm on a rv

2007-2008 Toyota Tundra Crew Cab Installation Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware with a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper re-installation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners located on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. A5a A5b 2007-08 Toyota Tundra Crew Cab By Gilbert R. Gutierrez Vehicle type: Four-door, crew-cab pickup truck NAGS numbers*: Windshield part numbers are FW02724, FW02723, FW02722 or FW02721; front door glass FD23323- 24 R-L; rear door glass FD23325-26 R-L; and back glass FY95054, FY95053, FB23336, FB23335 and FB23334. Helpful tools or supplies: Retention tape or a rubber hose to protect the fenders and hood; a PryBaby for molding and panel removal. Watch for: Be careful not to pull too hard on the rearview mirror harness during removal to avoid ripping the headliner. When removing or re-installing the A-pillar trim panels, take care to avoid disturbing the curtain air-bag harness. *With permission from National Auto Glass Specifications. Call NAGS at 800/551-4012 or visit www.nags.com. Vehicle information A1 A2 A3a A3b A4a A4b 35 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, and then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool to cut out the glass, remove the A-pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to dis- A6a A6b A6c A7a A11a A11b A12a A12b A7b A7c A8 A10 A13a A13b 36 AutoGlass™ •March/April 2008 Installation ? F or T echnicians Only turb the curtain air-bag harness when removing or re-installing the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers. Removal 14. Make sure cutting blades are sufficiently sharp. 15. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane. 16. If using a cold knife, use a 3? 4 -inch blade. Cut three sides; then use a long knife or power tool to cut the bottom of the windshield. Note: There are no gravity stops on this windshield. 17. If trying to save the windshield, use an Equalizer with an 8-inch blade. Note: When using any power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts. 18. After cutting the sides and top, cut out the bottom portion of the glass using an Equalizer Express. Spray the bottom of the windshield with water at least 4-to-5 inches above the urethane on the glass, so the water flows down into the urethane while you make your final cut across the bottom of the windshield. Caution: Never use your head to push, as this could result in back and neck injuries. 19. Take the windshield out of the opening using a set of vacuum cups. Lift the glass and place it on a windshield stand or suitable workstation. Installation 20. After cutting the windshield out, remove contaminants such as dirt, moisture and other debris from the pinchweld. Clean the dashboard. 21. Dry fit the new glass to the opening. Mark your glass using a grease pencil or molding-retention tape. 22. Place your vacuum cups on the windshield in the appropriate location for a one-person set. 23. For driver-side setting of the windshield using a Glass Handler Kit, place the kit’s elbow-setting pad on the driver’s side of the hood area; then lift the windshield from the stand using the vacuum cups. 24. Reach over, place your elbow on the setting pad and set the windshield onto the old urethane. 25. With the windshield resting in the opening, make sure it is in the right spot. 26. Adjust both sides to the correct setting, marking the passenger’s side, then the driver’s side. Lift the glass and place it on a windshield stand or suitable workstation. 27. Follow the urethane manufacturer’s recommendations for installation. 28. Clean the inside of the windshield using a urethane manufacturer-recommended product; follow recommended steps. Note: Do not touch the bonding area of the windshield after cleaning, prepping or priming it. 29. Wear powder-free Nitrile gloves to keep off chemicals. 30. Apply the glass prep and primer, following the urethane manufacturer’s recommendations.

Related Content:

ford 4500 backhoe parts radiator with oil cooler, fender removal 06 tundra, 2007 toyota tundra dash removal, INSTALLING FJ CRUISER WINDSHIELD, change out connector and pump for windsheild wash reservoir in 1990 Buick LeSabre, how to remove inside front windshield pillar molding 2013 escalade, how to remove tundra power seat switch, lincoln navigator windshield seal, repair windshield wiper arm on 2003 buick lesabre custom, silverado low washer fluid

2007-2008 Toyota Tundra Rear Driveshaft/ Propeller Shaft Clunk/ Thunk Noise Repair Manual

0

Filed Under (Toyota Manuals) by admin on 02-02-2012

download
Repair Procedure 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition Repair Procedure (Continued) 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing. 3. Test drive and confirm that NO abnormal vibrations or shudders occur while driving, and that the driveshaft clunk/thunk noise is eliminated.

Related Content:

2008 propel malibu 50cc scooter manual, how to change tranny fluid in malibu propell 50cc scooter, propel malibu, 2007 tundra drive shaft, tundra repair manual pdf, Tundra Drive Shaft Vibrations, toyota tundra 2007 instructions, Saab 9-7x differential clunk, repairs for drive shaft bearing, Propel Malibu starter 2008

1984 Mercedes Benz 190E Fuel Delivery and Air Induction Engine Testing And Adjustment Manual

0

Filed Under (Mercedes-benz Manuals) by admin on 13-04-2012

download
Note: Test and adjust lambda control with a lambda control tester. The lambda control and the idle speed emissions level must not be tested when the engine is very hot, e.g. immediately after driving sharply or after measuring engine output on the dynamometer. Testing, adjusting 1 Complete measurement sheet. 2 Switch off air conditioning or automatic climate control. Move selector lever into position “P”. 3 Read out DTC memory. Note: Not available on model year 1984-1986. 4 Connect testers: oil remote thermometer (018)124 589 07 21 00 lambda control tester (012) twin socket (031) trigger clamp (011) exhaust probe (005)126 589 11 63 00 CO measuring instrument (006) engine tester with oscilloscope (030) multimeter (003) test cable (033)102 589 04 63 00. 5 Position extraction device (014) at exhaust tail pipe. 6 Check engine coolant level, adjust to correct level. 7 Check engine oil level, pay attention to condition of oil (visual inspection). 8 Take off air cleaner. 9 Check ease of movement and condition of throttle control linkage and throttle valve. Grease all bearing points and ball sockets. 10 Check fulcrum lever, adjust. Check whether the roller (15) in the fulcrum lever (13) is resting free of tension against end stop. Adjust fulcrum lever (13) with the connecting rod (2), if necessary, so that the roller (15) is resting free of tension against end stop. 11 Idle stop. Check whether the throttle valve is resting against idle stop. Disconnect connecting rod (2) for this step. Adjust throttle control. Engines with cruise control only. Check whether the actuator is resting against idle stop of cruise control by pressing the lever of the actuator clockwise against idle stop at cruise control. When attaching the connecting rod (21), ensure that the lever of the actuator is lifted approx. 1 mm off the idle stop at the cruise control. Adjust tie rod, if necessary. Adjust throttle control. 12 Check wide open throttle stop from the accelerator pedal , adjust. 13 Voltages Test (battery and ignition coil ): No-load voltage Connect voltmeter to the battery, paying attention to the polarity, and take reading of voltage. Specification: 12.2 volts . Ignition coil Switch on ignition with engine not running. Test the voltage terminal 15 to ground at contact 5 of diagnostic connector. Specification: battery voltage Test difference in voltage between terminal 15 and terminal 1 at contacts 5 and 4 of diagnostic connector. Specification: 0 volts If the specified values are not reached, test

Related Content:

throttle control motor relay 05 mazda 3, 1986 190e 2 3 crank trigger test, 2007 Dodge Throttle Valve Actuator Installation Instructions, ax4n endplay pdf, carborator for mazda6 2003 manual gear, how to test actuator of stabilator, how to test throttle actuator motor, mb 1993 lamda code, throttle position sensor 1986 190e 16 valve

2007-2008 Toyota Tundra Extended Cab Installation Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
windshield Preparation 1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware using a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper reinstallation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three fasteners on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool for cutout, remove the A- pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby tool. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to disturb the curtain air-bag harness when removing or reinstalling the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers

2008 TOYOTA HIGHLANDER TRAILER WIRE HARNESS Preparation

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
1. Supplemental Restraint System (SRS) (a) Failure to carry out procedures listed below could result in possible deployment of airbag, personal injury, or unnecessary repairs to SRS. (b) Turn the key switch to the LOCK position. (Fig. 1-1) (c) Remove the key from the ignition switch. (d) Disconnect the negative battery cable. (Fig. 1-2) (e) Never use a voltmeter to troubleshoot any of the harnesses or connectors to the SRS. Accidentally probing the connectors to the SRS can lead to deployment of the airbag. (Fig. 1-3) (f) SRS wire harness loom/cover is bright yellow in color. Fig. 1-1 Fig. 1-2 Fig. 1-3 10 mm socket
TOYOTA HIGHLANDER 2008 – TRAILER WIRE HARNESS Procedure Page 5 of 16 pages Issue: A 04/13/07 2. Wiring Precautions (a) DO NOT pull on vehicle wires and/or wire harness. To uncouple electrical connectors, pull only on the connector. (Fig. 2-1) (b) Use nylon ties and adhesive foam strips to secure the vehicle harness and the trailer wire harness. (c) Ensure that all wires are properly insulated from ground. (d) When installing the trailer wire harness, make sure it is not cut or perforated by any sharp metal objects. 3. General Practices and Procedures (a) Before starting installation, refer to the supplemental restraint system procedures in Section 1 above. (b) Take care not to scratch any part of the vehicle. Bind the tips of tools (clip remover, slot screw driver, etc.) with vinyl tape to prevent damage to any part of the car, or use a nylon removal tool (resin based prying tool). (Fig. 3-1) (c) Use a small parts container to store removed bolts and tapping screws so that they can be reassembled correctly. (d) Ensure that seat/floor protectors are in position. (e) After fastening plastic ties, clip away all the excess of the ties using diagonal pliers. (Fig. 3-2)

Related Content:

fixing wiring harness connectors between trailer and jeep

2008-2010 FORD F-Super Duty DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 17-01-2012

download
DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE ISSUE ECT temp. Some 2008-2010 F-Super Duty vehicles built on or b. Test results/next steps: before 9/14/2009 and equipped with a 6.4L diesel engine may exhibit repeat radiator leaks due to (1) If EOT is less than 8 °F (4.4 °C) malfunctioning (hyper-extended) high temperature higher than ECT, and the coolant temp thermostats. fluctuates roughly 5 °F (2.7 °C) – the thermostats are okay and do not need ACTION to be replaced. Replace just the Follow the Service Procedure steps to correct the radiator. Refer to WSM, Section 303-03 condition. (Engine Cooling). SERVICE PROCEDURE (2) If EOT exceeds ECT by greater than 8 °F (4.4 °C) or if the ECT readings 1. Verify the coolant leak is from the radiator, refer fluctuate 10 to 12 °F (5.55-6.66 °C) to pinpoint test (PPT) A found in the Workshop roughly every 30 seconds – replace Manual (WSM), Section 303-03. both thermostats and radiator. Refer to 2. Verify the venturi tee is installed. WSM, Section 303-03 (Engine Cooling). a. If installed, confirm it is installed correctly (note – orientation direction on part). 5. If vehicle is not drivable and the coolant leak is found to be from the radiator, remove and b. If not installed, install Venturi Tee Kit on replace both thermostats and radiator. Refer to vehicles built on or before 5/15/2008. WSM, Section 303-03 for both radiator and thermostat removal procedure and approved 3. Prepare the vehicle for a test drive. cooling system draining, filling and bleeding a. If the coolant leak at the radiator is large procedures. enough to cause an unsafe test drive or potential for engine/vehicle damage, proceed PART NUMBER PART NAME to Step 5. 8C3Z-8575-D Thermostat Assembly 8C3Z-8009-B Radiator Assembly b. Before driving the vehicle confirm the 8C3Z-8B379-B Venturi Tee coolant level is at minimum level or above in the degas bottle. If required, add 50/50 WARRANTY STATUS: Eligible Under Provisions Of mix to coolant bottle. New Vehicle Limited Warranty Coverage 4. Test Drive – use an Integrated Diagnostic IMPORTANT: Warranty System (IDS) or equivalent and monitor engine coverage limits/policies are oil temperature (EOT) and engine coolant not altered by a TSB. temperature (ECT) parameter identifiers (PIDS). Warranty coverage limits are determined by the identified causal par

Related Content:

08 f350 radiator replacemnt, how to change thermostat in a 2011 chevy cruze, 2010 F150 Thermostat, f150 ceiling leak, ford focus thermostat does both ends move when hot, replacing saturn aura xe 2008 cooling fan, thermostat housing bolts 2009 focus torkspec

2005 -2008 Toyota Tacoma Tailgate Lock PL5200 Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Lock Assembly 2 Washers, 2 Nuts 2 Rod Extenders Instructions Warranty Card Tools Required: Screw Driver T-30 Torx 7 mm Socket Tech Support: Call 1-800-342-5911 Installation Instructions Tailgate Lock PL5200 Toyota Tacoma 2005 -2008 4. Turn tailgate over and put segmented washer over one of the studs 5. Screw the nut onto the stud. Repeat steps 4 and 5 on the other stud and tighten both nuts. 6. Rotate plastic rod retainer using a screw driver and remove rod. 7. 1. Insert rod into Extender slot 2. Twist Extender to retain the rod. 8. 1. Insert Extender onto arm. 2. Twist rod retainer over the Extender. 9. Repeat steps 6, 7 and 8 on the second rod to finish the installation. NOTE: If the tailgate will not open when unlocked, remove the rod extenders LIMITED WARRANTY TERMS AND CONDITIONS 1. INSTALLATION: Pop & Lock TM is not responsible for installing the Pop & Lock TM or for the harm suffered by any person as a result of installing it. 2. WARRANTIES: a) Customer acknowledges that it is unreasonable to believe that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so-called anti-theft or security device is that it will deter many theives. b) POP & LOCK TM MAKES, AND THE CUSTOMER RECEIVES, NO WARRANTY, EXPRESSED OR IMPLIED, EXCEPT THE WARRANTIES OF TITLE TO THE POP & LOCK TM AND THEIR MERCHANTABILITY, PARTICULARLY NO WARRANTY OF FITNESS FOR A PARTICULAR USE OR PURPOSE OR AGAINST INFRINGEMENT. c) As Customer’s only remedy, Pop & Lock TM will repair or replace, at its option and without charge, any lock that is defective in material or workmanship when received by the Customer and is returned to Pop & Lock TM , FOB Pop & Lock’s offices, within one (1) year after its receipt by the Customer. Pop & Lock TM will ship all replacement, or repaired locks to the Customer, FOB Pop & Lock’s shipping point.

Related Content:

diy tailgate lock, 2008 toyota tacoma pdf manual, 2011 toyota tundra camera within tailgate without key hole, diy tacoma power tailgate lock, free toyota tacoma repair manual RM576U2, grease points 2005 -2013 tacoma lube points, How do I install a locking tailgate handle on Tacoma Truck, how to replacere glove box lock 2008 grand prix

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, 2008 checrolet colorodo emmisions purge valve, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 pilot alternator replacement, how to change the thermostat 2008 ford escape ehow, inhrdvd1000 parts, 2008 saturn outlook transmission pressure solenoid, hummer h3 2008 p0741, 2008 f250 haynes pdf