2008 toyota camry plastic undercarriage 2009

You search PDF repair manual about 2008 toyota camry plastic undercarriage 2009, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 toyota camry plastic undercarriage 2009 Direct Download speed 5432 Kb/s

  2008 toyota camry plastic undercarriage 2009 Full Version speed 8172 Kb/s



Toyota ISO Adapter Wiring Diagram

0

Filed Under (Toyota Manuals) by admin on 19-05-2011

download
4R Runner 1991-2000 Amazon > 2000 Avensis > 1997 Avensis verso > 2003 Camry > 1991 Carina E > 1988 Celica > 1990 Corolla > 1988 Corolla verso > 2002 Hi-Ace > 1990 Hi-Lux > 1989 Land Cruiser 1984-2002 Lite Ace > 1993 MR2 > 1990 Paseo > 1997 Picnic > 1990 Previa > 1994 RAV-4 > 1994 Starlet 1993-1997 Supra 1986-1996 Tacoma 1995-2001 Yaris > 1999 Reference : AC000005AA If you are interested, contact our sales department : Car kit Parrot Battery Pin Number Couleur Description 1 White Mute In 1 2 Yellow Mute In 2 3 Blue Mute In 3 4 Orange + 12V Memory 5 Green 6 Brown 7 Red + 12 V Permanent 8 Black Masse Car kit Parrot, car’s speakers Pin Number Couleur Description 1 Grey Rear right speaker + 2 White Rear right speaker – 3 Blue Front right speaker + 4 Green Front right speaker – 5 Red Front left speaker + 6 Orange Front left speaker – 7 Bronw Rear left speaker + 8 Black Rear left speaker – Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 2 Green Rear left speaker + 2 Toyota 1 White Front left speaker + 1 Toyota 1 Grey Front Right speaker + 1 Toyota 2 Violet Rear Right speaker + 3 Toyota 2 Green Black Rear Left speaker – 9 Toyota 1 White Black Front Left speaker – 10 Toyota 1 Grey Black Front Right speaker- 6 Toyota 2 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 1 Red +12 V Permanent 4 Toyota 1 Orange +12 Ignition 8 Toyota 1 Black Ground Toyota 1 Toyota 2 Toyota Audio Toyota Supply N° Connector Color Description 2 Toyota 4 Green Rear left speaker + 2 Toyota 3 White Front left speaker + 1 Toyota 3 Grey Front Right speaker + 1 Toyota 4 Violet Rear Right speaker + 3 Toyota 4 Green Black Rear Left speaker – 9 Toyota 3 White Black Front Left speaker – 10 Toyota 3 Grey Black Front Right speaker- 6 Toyota 4 Black Violet Rear Right speaker – N° Connector Color Description 3 Toyota 3 Red +12 V Permanent 4 Toyota 3 Orange +12 Ignition 8 Toyota 3 Black Ground

Related Content:

2002 toytoa camry tank vent valve, toyota 4af engine repair manual, 1998 toyota A245E automatic transmission rebuild manual, p67-y toyota vitz, 2002 toyota tundra 4 wheel drive suspencion, p1225 spill control circuit, diagram of front passenger seat occupant sensors and where 2005 toyota camry located, show prado 1999 valve attached to rear brake pipe with spring, 2009sienna v6 thermostadt extraction, 2004 toyota highlander window diagram

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, 2008 checrolet colorodo emmisions purge valve, how to change the thermostat 2008 ford escape ehow, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 pilot alternator replacement, Kia Spectra Repair Manual PDF, 2008 f250 haynes pdf, hummer h3 2008 p0741, 2008 toyota tundra tailgate latch assembly

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 6m70 engine manual pdf, cft30 scan codes, 1999 chevy S10 - manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, pdf kancil 850 manual tranission, 2006 ford focus ses repair manual, 1996 buick regal 3800 owners mAnuel

1999 Toyota Corolla Radio Replacement

0

Filed Under (Toyota Manuals) by admin on 12-05-2011

download
The radio is secured to the frame of the vehicles dash with screws located behind the plastic dash panel surrounding the radio. This plastic dash panel unsnaps from the body of the vehicles dash. STEP 2 : The bottom of the plastic dash panel, just below the bottom of the radio, can be lifted up. Look up from the below the radio and you will notice rectangular openings or insertion points where a flat tool can be inserted to pry out the bottom of the plastic dash panel. With a flat head screwdriver or other flat object, pry out the bottom of the plastic dash panel STEP 3 : Once the bottom edge of the plastic dash panel has been pulled out, the sides of the plastic dash panel will begin to separate from the body of the vehicles dash. You will now be able to put your fingers into the openings on the sides of the plastic dash panel. Gently pull the plastic dash panel until it unsnaps from the body of the vehicles dash. Remove Factory Radio Move to: Wire New Radio Section Wiring The New Radio Move to: Mounting New Radio Section The Install Doctor STRONGLY recommends purchasing a ‘DIN’ radio for this vehicle. ‘DIN’ radios are a direct replacement for the Toyota radio in this vehicle. More information is available in the Mounting New Radio section. Mounting The Radio Options STEP 4 : Once all the clips on the plastic dash panel have been unsnapped, the dash can be pulled out. The top of the plastic dash panel will have wires attached to the clock, hazard and defrost switches. You do NOT need to unplug the connectors plugged into them. Move the plastic dash panel up and set it on top of the body of the dash. STEP 5 : The radio is held in with four (4) phillips screws / 8 mm bolts . Remove the screw/bolts. Pull the radio forward. Unplug the antenna cable, and 2 white connectors from the rear of the radio

Related Content:

toyota venza dashboard repair manual, Plastic Bezel Watch Instructions, 1995 ford 555d backhoe dashboard warning light, tsb #00-25-6, set hino dashboard clock, plastic bezel 1011 watch manual, no sienna dash lights, how to renove upper dah panel 2013 avalon, how install 2001 camaro dash panel, hino 268 dash warning lights

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, nut size used to hold brake calipers on a toyota corolla vvti 1 5, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

2007-2008 Toyota Tundra Crew Cab Installation Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware with a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper re-installation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners located on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. A5a A5b 2007-08 Toyota Tundra Crew Cab By Gilbert R. Gutierrez Vehicle type: Four-door, crew-cab pickup truck NAGS numbers*: Windshield part numbers are FW02724, FW02723, FW02722 or FW02721; front door glass FD23323- 24 R-L; rear door glass FD23325-26 R-L; and back glass FY95054, FY95053, FB23336, FB23335 and FB23334. Helpful tools or supplies: Retention tape or a rubber hose to protect the fenders and hood; a PryBaby for molding and panel removal. Watch for: Be careful not to pull too hard on the rearview mirror harness during removal to avoid ripping the headliner. When removing or re-installing the A-pillar trim panels, take care to avoid disturbing the curtain air-bag harness. *With permission from National Auto Glass Specifications. Call NAGS at 800/551-4012 or visit www.nags.com. Vehicle information A1 A2 A3a A3b A4a A4b 35 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, and then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool to cut out the glass, remove the A-pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to dis- A6a A6b A6c A7a A11a A11b A12a A12b A7b A7c A8 A10 A13a A13b 36 AutoGlass™ •March/April 2008 Installation ? F or T echnicians Only turb the curtain air-bag harness when removing or re-installing the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers. Removal 14. Make sure cutting blades are sufficiently sharp. 15. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane. 16. If using a cold knife, use a 3? 4 -inch blade. Cut three sides; then use a long knife or power tool to cut the bottom of the windshield. Note: There are no gravity stops on this windshield. 17. If trying to save the windshield, use an Equalizer with an 8-inch blade. Note: When using any power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts. 18. After cutting the sides and top, cut out the bottom portion of the glass using an Equalizer Express. Spray the bottom of the windshield with water at least 4-to-5 inches above the urethane on the glass, so the water flows down into the urethane while you make your final cut across the bottom of the windshield. Caution: Never use your head to push, as this could result in back and neck injuries. 19. Take the windshield out of the opening using a set of vacuum cups. Lift the glass and place it on a windshield stand or suitable workstation. Installation 20. After cutting the windshield out, remove contaminants such as dirt, moisture and other debris from the pinchweld. Clean the dashboard. 21. Dry fit the new glass to the opening. Mark your glass using a grease pencil or molding-retention tape. 22. Place your vacuum cups on the windshield in the appropriate location for a one-person set. 23. For driver-side setting of the windshield using a Glass Handler Kit, place the kit’s elbow-setting pad on the driver’s side of the hood area; then lift the windshield from the stand using the vacuum cups. 24. Reach over, place your elbow on the setting pad and set the windshield onto the old urethane. 25. With the windshield resting in the opening, make sure it is in the right spot. 26. Adjust both sides to the correct setting, marking the passenger’s side, then the driver’s side. Lift the glass and place it on a windshield stand or suitable workstation. 27. Follow the urethane manufacturer’s recommendations for installation. 28. Clean the inside of the windshield using a urethane manufacturer-recommended product; follow recommended steps. Note: Do not touch the bonding area of the windshield after cleaning, prepping or priming it. 29. Wear powder-free Nitrile gloves to keep off chemicals. 30. Apply the glass prep and primer, following the urethane manufacturer’s recommendations.

Related Content:

ford 4500 backhoe parts radiator with oil cooler, fender removal 06 tundra, 2007 toyota tundra dash removal, INSTALLING FJ CRUISER WINDSHIELD, change out connector and pump for windsheild wash reservoir in 1990 Buick LeSabre, how to remove inside front windshield pillar molding 2013 escalade, how to remove tundra power seat switch, lincoln navigator windshield seal, repair windshield wiper arm on 2003 buick lesabre custom, silverado low washer fluid

2009 Toyota Corolla TWM Performance Short Shifter Installation Manual

0

Filed Under (Toyota Manuals) by admin on 29-11-2011

download
1. Unscrew the shift knob by rotating it counter clockwise and put it in a safe place for re-install later. 2. Pull the shift boot up over the plastic shift boot retainer. 3. Pull up the shift boot console from both sides to pop it off the center console, do not remove it at this time simply pop it off the main console Continue the shift boot console removal by pulling on the plastic part that goes up the sides of the climate controls as shown. These parts need to be pulled off with some force but are left in place for now, just disconnect them. 5. With the side plastic pieces popped free you now have access to a Phillips head screw on each side of the console. Remove these screws using a Phillips head screwdriver. Put the screws aside in a safe place for re-install later. 6. Disconnect the white clip for the lighter under the shift boot console by pulling down on the white plastic part Remove the shift boot console from the car and put it aside in a safe place for re-install later. 8. Open the center storage compartment. Using a flat head screwdriver, pry up on the middle part of the center console as shown on the pictures to the left. There are grooves where a flat head screwdriver can be inserted to pry up. Slide the e-brake boot over the e- brake lever as shown to the left. 10. Remove the middle part of the center console as pictured to the left. Put it aside in a safe place for re-install later. 11. Remove the small mat from the center compartment to gain access to the two 10mm bolts at the bottom of the compartment. You can unbolt these using a 10mm socket with a ratchet and a ratchet extension. Place the two bolts aside in a safe place for re-install later

Related Content:

er90 safeplace

2008 TOYOTA HIGHLANDER TRAILER WIRE HARNESS Preparation

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
1. Supplemental Restraint System (SRS) (a) Failure to carry out procedures listed below could result in possible deployment of airbag, personal injury, or unnecessary repairs to SRS. (b) Turn the key switch to the LOCK position. (Fig. 1-1) (c) Remove the key from the ignition switch. (d) Disconnect the negative battery cable. (Fig. 1-2) (e) Never use a voltmeter to troubleshoot any of the harnesses or connectors to the SRS. Accidentally probing the connectors to the SRS can lead to deployment of the airbag. (Fig. 1-3) (f) SRS wire harness loom/cover is bright yellow in color. Fig. 1-1 Fig. 1-2 Fig. 1-3 10 mm socket
TOYOTA HIGHLANDER 2008 – TRAILER WIRE HARNESS Procedure Page 5 of 16 pages Issue: A 04/13/07 2. Wiring Precautions (a) DO NOT pull on vehicle wires and/or wire harness. To uncouple electrical connectors, pull only on the connector. (Fig. 2-1) (b) Use nylon ties and adhesive foam strips to secure the vehicle harness and the trailer wire harness. (c) Ensure that all wires are properly insulated from ground. (d) When installing the trailer wire harness, make sure it is not cut or perforated by any sharp metal objects. 3. General Practices and Procedures (a) Before starting installation, refer to the supplemental restraint system procedures in Section 1 above. (b) Take care not to scratch any part of the vehicle. Bind the tips of tools (clip remover, slot screw driver, etc.) with vinyl tape to prevent damage to any part of the car, or use a nylon removal tool (resin based prying tool). (Fig. 3-1) (c) Use a small parts container to store removed bolts and tapping screws so that they can be reassembled correctly. (d) Ensure that seat/floor protectors are in position. (e) After fastening plastic ties, clip away all the excess of the ties using diagonal pliers. (Fig. 3-2)

Related Content:

fixing wiring harness connectors between trailer and jeep

Toyota FJ CRUISER Color panel Kit Installation Manual

0

Filed Under (Toyota Manuals) by admin on 21-05-2011

download
MODEL YEAR MODELS DESCRIPTION PART NUMBER PPO Code 2008 – 2009 All BLU Logic Hands Free System, large button PT923-00091 B3 Note: NON-JBL Audio Only, NON-Navigation Audio only Please confirm that a “knock-out” plate is available in the vehicle to mount the switch prior to ordering. 2007 – 2009 All Interface kit for iPod PT545-00082 P5 Note: Requires audio head unit to be satellite ready. Some preminum audio units have embedded XM and conflict with the iPOD Interface kit. The 2009 Corolla and 2009 Matrix with Premium Audio (JBL) has embedded XM and conflicts with the iPOD Interface. Some base grade audio are not satellite ready. Either iPOD or Sat Radio can be installed, not both. Compatible iPOD Models: iPOD mini iPOD 4th & 5th generation iPOD nano 1st , 2nd & 3rd generation iPOD touch iPHONE 2008 – 2010 All Satellite Radio, XM, Receiver 86180-0W031 P7 Note: DIO requires ordering specific fit kit and receiver for complete installation. PPO includes both fit kit and receiver. 86180-0W031 required for 08MY Landcruiser. PPO price may differ by vehicle. 2007 – 2010 All Satellite Radio, XM, Fit Kit PT546-35070 P7 Note: Requires fit kit. PPO included both fit kit and receiver. Satellite radio is only available on FJ’s with Upgrade Package #1 or #2. 2007 – 2009 All Satellite Radio, SIRIUS, Fit Kit PTS31-35070 P2 Note: Fit kit is sold PPO as a complete kit which also includes the applicalbe receiver kit. Fit kit requires applicable receiver kit to complete the installation. Satellite radio is only available on FJ’s with Upgrade Package #1 (UP)or #2 (UR). 2007 – 2010 All Satellite Radio, SIRIUS, Receiver PTS31-53060 P2 Note: Requires separate fit kit to complete installation. Applicable only to vehicles that have JBL satellite ready radio (SAT button)or 6CD Changer(Some Models). This part replaces PTS31- 00052. PPO Dealer Cost and PPO MSRP is for entire kit (P2). Highlander application includes hybrid models.

2005 -2008 Toyota Tacoma Tailgate Lock PL5200 Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Lock Assembly 2 Washers, 2 Nuts 2 Rod Extenders Instructions Warranty Card Tools Required: Screw Driver T-30 Torx 7 mm Socket Tech Support: Call 1-800-342-5911 Installation Instructions Tailgate Lock PL5200 Toyota Tacoma 2005 -2008 4. Turn tailgate over and put segmented washer over one of the studs 5. Screw the nut onto the stud. Repeat steps 4 and 5 on the other stud and tighten both nuts. 6. Rotate plastic rod retainer using a screw driver and remove rod. 7. 1. Insert rod into Extender slot 2. Twist Extender to retain the rod. 8. 1. Insert Extender onto arm. 2. Twist rod retainer over the Extender. 9. Repeat steps 6, 7 and 8 on the second rod to finish the installation. NOTE: If the tailgate will not open when unlocked, remove the rod extenders LIMITED WARRANTY TERMS AND CONDITIONS 1. INSTALLATION: Pop & Lock TM is not responsible for installing the Pop & Lock TM or for the harm suffered by any person as a result of installing it. 2. WARRANTIES: a) Customer acknowledges that it is unreasonable to believe that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so-called anti-theft or security device is that it will deter many theives. b) POP & LOCK TM MAKES, AND THE CUSTOMER RECEIVES, NO WARRANTY, EXPRESSED OR IMPLIED, EXCEPT THE WARRANTIES OF TITLE TO THE POP & LOCK TM AND THEIR MERCHANTABILITY, PARTICULARLY NO WARRANTY OF FITNESS FOR A PARTICULAR USE OR PURPOSE OR AGAINST INFRINGEMENT. c) As Customer’s only remedy, Pop & Lock TM will repair or replace, at its option and without charge, any lock that is defective in material or workmanship when received by the Customer and is returned to Pop & Lock TM , FOB Pop & Lock’s offices, within one (1) year after its receipt by the Customer. Pop & Lock TM will ship all replacement, or repaired locks to the Customer, FOB Pop & Lock’s shipping point.

Related Content:

diy tailgate lock, 2008 toyota tacoma pdf manual, 2011 toyota tundra camera within tailgate without key hole, diy tacoma power tailgate lock, free toyota tacoma repair manual RM576U2, grease points 2005 -2013 tacoma lube points, How do I install a locking tailgate handle on Tacoma Truck, how to replacere glove box lock 2008 grand prix

Related Content:

2002 toytoa camry tank vent valve, toyota 4af engine repair manual, 1998 toyota A245E automatic transmission rebuild manual, p67-y toyota vitz, 2002 toyota tundra 4 wheel drive suspencion, p1225 spill control circuit, diagram of front passenger seat occupant sensors and where 2005 toyota camry located, show prado 1999 valve attached to rear brake pipe with spring, 2009sienna v6 thermostadt extraction, 2004 toyota highlander window diagram