Skip to content

2008 toyota tundra repair

You search PDF repair manual about 2008 toyota tundra repair, if there are search results will appear below. If search results do not exist, please search by others keyword.

2007-2008 Toyota Tundra Rear Driveshaft/ Propeller Shaft Clunk/ Thunk Noise Repair Manual

download
Repair Procedure 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition Repair Procedure (Continued) 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing. 3. Test drive and confirm that NO abnormal vibrations or shudders occur while driving, and that the driveshaft clunk/thunk noise is eliminated.

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

2007-2008 Toyota Tundra Crew Cab Installation Manual

download
1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware with a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper re-installation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners located on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. A5a A5b 2007-08 Toyota Tundra Crew Cab By Gilbert R. Gutierrez Vehicle type: Four-door, crew-cab pickup truck NAGS numbers*: Windshield part numbers are FW02724, FW02723, FW02722 or FW02721; front door glass FD23323- 24 R-L; rear door glass FD23325-26 R-L; and back glass FY95054, FY95053, FB23336, FB23335 and FB23334. Helpful tools or supplies: Retention tape or a rubber hose to protect the fenders and hood; a PryBaby for molding and panel removal. Watch for: Be careful not to pull too hard on the rearview mirror harness during removal to avoid ripping the headliner. When removing or re-installing the A-pillar trim panels, take care to avoid disturbing the curtain air-bag harness. *With permission from National Auto Glass Specifications. Call NAGS at 800/551-4012 or visit www.nags.com. Vehicle information A1 A2 A3a A3b A4a A4b 35 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, and then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool to cut out the glass, remove the A-pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to dis- A6a A6b A6c A7a A11a A11b A12a A12b A7b A7c A8 A10 A13a A13b 36 AutoGlass™ •March/April 2008 Installation ? F or T echnicians Only turb the curtain air-bag harness when removing or re-installing the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers. Removal 14. Make sure cutting blades are sufficiently sharp. 15. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane. 16. If using a cold knife, use a 3? 4 -inch blade. Cut three sides; then use a long knife or power tool to cut the bottom of the windshield. Note: There are no gravity stops on this windshield. 17. If trying to save the windshield, use an Equalizer with an 8-inch blade. Note: When using any power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts. 18. After cutting the sides and top, cut out the bottom portion of the glass using an Equalizer Express. Spray the bottom of the windshield with water at least 4-to-5 inches above the urethane on the glass, so the water flows down into the urethane while you make your final cut across the bottom of the windshield. Caution: Never use your head to push, as this could result in back and neck injuries. 19. Take the windshield out of the opening using a set of vacuum cups. Lift the glass and place it on a windshield stand or suitable workstation. Installation 20. After cutting the windshield out, remove contaminants such as dirt, moisture and other debris from the pinchweld. Clean the dashboard. 21. Dry fit the new glass to the opening. Mark your glass using a grease pencil or molding-retention tape. 22. Place your vacuum cups on the windshield in the appropriate location for a one-person set. 23. For driver-side setting of the windshield using a Glass Handler Kit, place the kit’s elbow-setting pad on the driver’s side of the hood area; then lift the windshield from the stand using the vacuum cups. 24. Reach over, place your elbow on the setting pad and set the windshield onto the old urethane. 25. With the windshield resting in the opening, make sure it is in the right spot. 26. Adjust both sides to the correct setting, marking the passenger’s side, then the driver’s side. Lift the glass and place it on a windshield stand or suitable workstation. 27. Follow the urethane manufacturer’s recommendations for installation. 28. Clean the inside of the windshield using a urethane manufacturer-recommended product; follow recommended steps. Note: Do not touch the bonding area of the windshield after cleaning, prepping or priming it. 29. Wear powder-free Nitrile gloves to keep off chemicals. 30. Apply the glass prep and primer, following the urethane manufacturer’s recommendations.

2004 Toyota Sienna POWER SLIDING DOOR INOPERATIVE Repair Manual

download
Remove Slide Door Window Garnish. A. Fully open the slide door window. B. Remove the glass run. C. Using a screwdriver, disengage the clip and remove the garnish. HINT: Tape the screwdriver tip before use. D. Using the taped screwdriver, disengage the 2 claws and remove the inner weatherstrip from the garnish. Parts Information Repair Procedure Clip POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 3 of 7 2. Remove Side Trim Board Cover Rear. A. Remove the 2 screws. B. Using the taped screwdriver, disengage the 8 claws and remove the cover together with the window control switch. C. Remove the 2 screws and window control switch. 3. Remove Rear Door Trim Board Sub-assembly. A. Remove the screw. B. Using the taped screwdriver, disengage the 9 clips and remove the trim board. HINT: In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by the arrows in the illustration. 4. Remove Rail End Molding. A. Open the quarter glass. B. Using the taped screwdriver, disengage the clip and 2 claws, and remove the rail end molding. Repair Procedure (Continued) : Claw 1 2 3 4 5 5 4 3 2 1 Protective Tape Protective Tape : Clip : Clip : Claw POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 4 of 7 5. Remove Center Bracket No. 2. A. Remove the 2 bolts and Center Bracket No. 2 together with the tensioner (color: white). B. Remove the tensioner from Center Bracket No. 2. 6. Remove Center Bracket No. 1. A. Remove the 2 bolts and Center Bracket No. 1 together with the tensioner (color: black). B. Remove the tensioner from Center Bracket No. 1. 7. Remove Slide Door Window Assembly LH. A. With Sunshade: Remove the sun shade hook. B. Remove the bolt and window frame. C. Remove the bolt. D. Loosen the nut. E. Push the rear lower window frame in the direction indicated by the arrow in the illustration

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked