Skip to content

2010 f150 rear end clunk

You search PDF repair manual about 2010 f150 rear end clunk, if there are search results will appear below. If search results do not exist, please search by others keyword.

2009-2010 FORD F-150 REAR DRIVESHAFT SLIP/ BUMP SERVICE PROCEDURE

download
SERVICE PROCEDURE 8. Evenly coat the driveshaft splines with 0.53-0.71 ounces (15-20 grams) of Motorcraft® It is not necessary to remove the entire driveshaft PTFE Lubricant. from the vehicle for this repair. 9. Position boot and clamps over the spline 1. Place orientation marks on the rear driveshaft portion of the driveshaft. Do not crimp the flange and differential pinion flange. clamp at this time. 2. Mark the center slip yoke barrel across the boot 10. Install the rear portion of the driveshaft into the and the clamp crimp heads to the rear shaft center slip yoke. spline stud shoulder. (Figure 1) 11. Fasten driveshaft flange to the rear axle using the previous alignment marks for reference. Refer to WSM, Section 205-01 for detail. 12. Position the clamp heads in-line with the alignment mark on the slip yoke and stud spline shoulder to minimize any balance shift. 13. Crimp clamps using ESST 205-343. Other driveline noise conditions will not be corrected with this procedure. Refer to appropriate WSM for diagnosis and repair for engagement clunk, hesitation during light throttle 1-2 upshift, harsh downshift while coasting 15 MPH (24 Km/h) and, shudder/vibration on moderate to hard acceleration. Figure 1 – Article 09-25-5 See other applicable Technical Service Bulletins for 3. Remove the clamps from the center slip yoke details. and discard.

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

2007-2008 Toyota Tundra Rear Driveshaft/ Propeller Shaft Clunk/ Thunk Noise Repair Manual

download
Repair Procedure 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition Repair Procedure (Continued) 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing. 3. Test drive and confirm that NO abnormal vibrations or shudders occur while driving, and that the driveshaft clunk/thunk noise is eliminated.

2009-2010 Toyota Venza DIN Head Unit Provision With Pocket Installation Manual

download
Toyota Venza 2009-2010 1 D isconnect the negative battery terminal to prevent an accidental short circuit. 1 Unclip and remove the trim panel to the right of the shifter. ( Figure A) 2 Remove (1) Phillips screw from the bottom of the climate control then unclip and remove the climate control. (Figure B) 3 Remove (4)10 MM bolts securing the radio. Note: You will need a universal swivel head socket adapter to get to the bottom left bolt. (Figure C) 4 Remove (4) Phillips screws securing the factory radio to the a/c vent panel. ( Figure D) 5 A B C REAR VIEW-RADIO AND A/CVENT PANEL RADIO D Continue to kit assembly . 99-8225G KIT ASSEMBLY 2 REAR VIEW-A/C VENT PANEL A B C D Secure the Radio Housing into the factory a/c vent panel using the factory hardware. (Figure A) 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the aftermarket head unit into the cage and secure. (Figure C) 4 * Note: Refer also to the instructions included with the aftermarket radio. DIN HEAD UNIT PROVISION WITH POCKET Reassemble remaining radio and dash assemblies in reverse order of disassembly. 5 6 Snap the factory vent panel/Radio Housing over dash cavity. (Figure D) 99-8225G KIT ASSEMBLY 3 REAR VIEW-A/C VENT PANEL A B C D Secure the Radio Housing into the factory a/c vent panel using the factoryhardware. (Figure A) 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 2 Slide the head unit into the radio opening until the side clips engage. (Figure C) 3 Snap the Trim Plate into the Radio Housing. (Figure C) 4 * Note: Refer also to the instructions included with the aftermarket radio. ISO DIN HEAD UNIT PROVISION WITH POCKET 5 Snap the factory vent panel/Radio Housing over dash cavity. (Figure D) Reassemble remaining radio and dash assemblies in reverse order of disassembly

2003 Volvo S40 L4-1.9L Rear Brake Pads Removal And Installation Manual

download
the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective. NOTE: If the dirt guard is defective, dirt may have penetrated the cylinder. Therefore the brake caliper must be reconditioned. Checking the rear brake disc Check the brake disc surface. Check the lateral runout of the brake disc if the disc is uneven. Replace the brake disc if it is worn or grooved. NOTE: Minimum disc thickness = 8.4 mm . If installing new brake pads, the minimum disc thickness must be at least 8.9 mm . Checking the locating pins for the rear brake calipers Check the rubber sleeves on the locating pins. Replace if necessary. If necessary, lubricate the locating pins using Volvo silicon grease (P/N 1161325-4). Insert the locating pins in the rubber sleeves. The locating pins must slide into the sleeves easily. Rotating the brake piston backwards Block the brake caliper against the brake disc. Use special tool 999 5782. * Turn the plate (A) forward over the shaft and insert the tool * Install the lugs (B) in the cut-out in the brake piston * Turn the shaft (C) so that the plate (A) presses against the brake caliper * Turn the axle (D) to the right and press the piston back while turning the shaft (C) to the right so that the plate (A) is in contact with the brake caliper * Turn the brake piston back fully and remove the tool Install the wear indicator (A) on the under side of the inner installed brake pads. Install the brake pads. Position the brake caliper . Install the new locking bolt. Tighten to 33 Nm . Install the brake hose in the support. Install the retaining clip. NOTE: Secure adhesive foil onto the steel plates to prevent the rear brake pads from rattling. Installing the wheels Install wheels. Checking the brake fluid level WARNING: Always depress the brake pedal repeatedly before test driving the car. Check the brake fluid level