2010 ford escape axle seal leak

You search PDF repair manual about 2010 ford escape axle seal leak, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2010 ford escape axle seal leak Direct Download speed 5432 Kb/s

  2010 ford escape axle seal leak Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Torque specs for 2008 prius axle nuts, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, removing front axel bearing 05 chevy 4x4, 2006 gmc envoy cv drive axles, rearaxleremovamodelaford, remove front diff bearing in navagator

Troubleshooting and Resolving Water Leaks for FUNSPORT Sunroofs

0

Filed Under (More Manuals) by admin on 13-03-2012

download
1. Opening the sunroof, just after it rains. Standing water on the glass will usually result in water dripping into the cabin. This is not a sunroof fault. Prevention is the solution! Simply drive a short distance to allow any standing water to blow off the glass prior to opening the sunroof. 2. Only after a car wash. High pressure water sprayed directly at the seal will often deflect the seal enough to enter the cabin. This is not a sunroof fault. Prevention is the solution! Don’t spray high pressure water directly on the seal. 3. During a rainstorm, water is immediately visible dripping on the rubber seal under the glass. There may be a problem with glass to seal contact. Carefully examine the seal. If it is visibly damaged or worn, it may need replacement. If dirty, it needs cleaning. An adjustment may solve the problem. Always water test to verify (see sprinkle test procedure below). a. Often dirt or debris will prevent proper contact between the glass and seal. Clean both the glass and seal with plain water (a damp cloth), or if very dirty, a mild detergent solution. Repeat water test after cleaning. If water intrusion between glass and seal continues, adjust the glass hardware. b. Adjust the glass hardware to increase clamping pressure on the seal. See procedure below. Repeat water test after adjusting. If water intrusion between glass and seal continues, replace seal. 4. Water is visible dripping through the glass hardware: Water test to verify (soak and sprinkle). You may need to slightly shift the glass hardware or change the rubber gaskets under the rectangular mounting plates. 5. After a long soaking rain the headliner gets wet. This is likely the result of water coming under the main frame or under the seal. Only a soak test will prove this. a. Under the main frame: remove the screw cover strip or pull back the headliner (of wrapped) and examine the clamping screws. Water spots or rusty screws are an indication that water is coming under the main frame. Remove the clamp frame and water spots or rust will likely be visible on the inside of the roofskin. This can be the result of an over-cut hole, a sunroof not centered on the hole (left a gap) or inadequate sealant. Solution: Remove the sunroof and re-install with new sealant. If the hole was over-cut, a larger size may be required. b. Underneath the main seal: carefully examine and verify proper seal insertion around perimeter of sunroof frame. Bottom of seal should be adhered to main frame with butyl tape. Top outer lip should be mechanically inserted into groove in frame. You may be able to manipulate the seal slightly to correct the problem. Otherwise replace the seal. c. Frame joint: typically will see water spots or rust on hinge block and handle mounting screws, particularly on the right hand side. Remove the knock-in bead and examine the channel for water or water spots. Solution: pull back the main seal at the passenger side and apply a small amount of silicone sealant across the frame joint. Allow to dry before reinserting the main seal.

Related Content:

1997 lumina 3 1l thermostat adjustment dial?, seal for slip on muflers, how to seal compresion hose leak on 2000 bmw 528i, rear main seal leak 2006 suburban, rear seal replacement on 2003 Chevy Cavalier, reinstall 1929 ford rear glass replacement, removing axles 1998 ford expedition, Replacing rear main seal 2003 suburban, ridgeline rear main seal tsb, to change seal on 2003 camshaft sensor

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

1994 Nissan Maxima SE FWD Axle Shafts Removal And Installation Manual

0

Filed Under (Nissan Manuals) by admin on 21-05-2011

download
FWD AXLE SHAFT Removal 1. Raise and support vehicle. Remove wheel. Remove wheel bearing lock nut from end of drive axle. Remove disc brake caliper and suspend out of way. DO NOT allow caliper to hang by hydraulic hose. 2. Separate tie rod end from steering knuckle. Remove axle shaft from steering knuckle hub using a soft mallet. On models with ball and cage type right axle shaft, remove support bearing retainer-to-block bolts. See Fig. 4 . 3. On all models, pry right axle shaft from transaxle using screwdriver. See Fig. 1 . On M/T models, pry left axle shaft from transaxle using screwdriver. On A/T models, insert screwdriver through right axle shaft hole in differential, and drive out left axle shaft. See Fig. 2 1. Place axle shaft in soft-jawed vise with inner joint facing up. Remove boot clamps. See Fig. 4 . Mark slide joint housing and inner race in relation to axle shaft for reassembly reference. 2. Remove and discard snap ring “A”. See Fig. 3 and Fig. 4 . Remove slide joint housing. Remove snap ring “C”. Remove cage, inner race and balls as an assembly. Remove snap ring “B”. Cover axle shaft splines with tape. Remove boot. 3. To disassemble support bearing and retainer assembly on right axle shaft, remove dust shield and snap ring “D”. See Fig. 4 . Press axle shaft out of support bearing and retainer assembly. Remove snap ring and dust shield from retainer. Using bearing driver and hammer, drive support bearing out of retainer.

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

2008-2010 FORD F-Super Duty DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 17-01-2012

download
DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE ISSUE ECT temp. Some 2008-2010 F-Super Duty vehicles built on or b. Test results/next steps: before 9/14/2009 and equipped with a 6.4L diesel engine may exhibit repeat radiator leaks due to (1) If EOT is less than 8 °F (4.4 °C) malfunctioning (hyper-extended) high temperature higher than ECT, and the coolant temp thermostats. fluctuates roughly 5 °F (2.7 °C) – the thermostats are okay and do not need ACTION to be replaced. Replace just the Follow the Service Procedure steps to correct the radiator. Refer to WSM, Section 303-03 condition. (Engine Cooling). SERVICE PROCEDURE (2) If EOT exceeds ECT by greater than 8 °F (4.4 °C) or if the ECT readings 1. Verify the coolant leak is from the radiator, refer fluctuate 10 to 12 °F (5.55-6.66 °C) to pinpoint test (PPT) A found in the Workshop roughly every 30 seconds – replace Manual (WSM), Section 303-03. both thermostats and radiator. Refer to 2. Verify the venturi tee is installed. WSM, Section 303-03 (Engine Cooling). a. If installed, confirm it is installed correctly (note – orientation direction on part). 5. If vehicle is not drivable and the coolant leak is found to be from the radiator, remove and b. If not installed, install Venturi Tee Kit on replace both thermostats and radiator. Refer to vehicles built on or before 5/15/2008. WSM, Section 303-03 for both radiator and thermostat removal procedure and approved 3. Prepare the vehicle for a test drive. cooling system draining, filling and bleeding a. If the coolant leak at the radiator is large procedures. enough to cause an unsafe test drive or potential for engine/vehicle damage, proceed PART NUMBER PART NAME to Step 5. 8C3Z-8575-D Thermostat Assembly 8C3Z-8009-B Radiator Assembly b. Before driving the vehicle confirm the 8C3Z-8B379-B Venturi Tee coolant level is at minimum level or above in the degas bottle. If required, add 50/50 WARRANTY STATUS: Eligible Under Provisions Of mix to coolant bottle. New Vehicle Limited Warranty Coverage 4. Test Drive – use an Integrated Diagnostic IMPORTANT: Warranty System (IDS) or equivalent and monitor engine coverage limits/policies are oil temperature (EOT) and engine coolant not altered by a TSB. temperature (ECT) parameter identifiers (PIDS). Warranty coverage limits are determined by the identified causal par

Related Content:

08 f350 radiator replacemnt, how to change thermostat in a 2011 chevy cruze, 2010 F150 Thermostat, f150 ceiling leak, ford focus thermostat does both ends move when hot, replacing saturn aura xe 2008 cooling fan, thermostat housing bolts 2009 focus torkspec

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, nut size used to hold brake calipers on a toyota corolla vvti 1 5, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 15-06-2012

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download

1994 Ford Explorer SPINDLE AND SHAFT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
Removal 1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub. See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION. 2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if equipped) and splash shield. 3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 . 4. Remove left shaft assembly (if required). On all applications, wrap spindle in protective cloth and place second step of spindle in soft-jawed vise. 5. On Explorer and Ranger, remove oil seal using slide hammer and Seal Remover (TOOL-1175-AC). Remove needle bearing from spindle. Press seal from shaft assembly. See Fig. 9 . 6. On Bronco and F150, remove needle bearing and oil seal using slide hammer and Cup Puller (T77F- 1102-A). Press seal from shaft assembly. Installation 1. Clean all dirt and grease from spindle bearing bore. Ensure bearing bore is free of nicks and burrs. On Explorer and Ranger, install seal on shaft assembly using press and Seal Installer (T83T-3132-A). 2. On Bronco and F150, install seal on shaft assembly, with seal lip toward spindle. On right side applications, install rubber boot and NEW keystone clamps on stub shaft. Install right shaft assembly into stub shaft, with stub shaft missing spline aligned with shaft assembly. 3. Ensure splines are fully engaged. Install rubber boot over assembly and tighten keystone clamps. On left axle applications, install shaft assembly through steering knuckle, and engage in splines. 4. Install needle bearing in spindle, with manufacturer identification mark facing away from spindle bore. For bearing installation, use Handle (T80T-4000-W), and Bearing/Seal Installer (T83T-3123-A for Explorer and Ranger; T80T-4000-S for Bronco and F150).

Related Content:

2005 f150 half wrap, how to replace a turbine speed sensor on a 1998 ford explorer, remove shaft 326rx service manual, spindle nut torque 2007 ford 150

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Torque specs for 2008 prius axle nuts, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, removing front axel bearing 05 chevy 4x4, 2006 gmc envoy cv drive axles, rearaxleremovamodelaford, remove front diff bearing in navagator