Skip to content

2011 prius shop manual

You search PDF repair manual about 2011 prius shop manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 Toyota Prius CAN-View module Installation Manual

download
I have seat covers on my Prius, which has a flap that extends under the back of the seat to attach with a Velcro strap. This crowds the CAN-View box if it is placed on top of the Nav box, as suggested in the installation instructions, as shown in the following: So I decided to put the CAN-View box in front of the Nav box, attached with Velcro (just the prickly part) to the rug. This shows the seat leaned back to give room to get to the plugs on the Nav box and more room to install the OBD cable under the dash. This shows how easy it is now, with the seat leaned back, to get to the cables in front of the Nav box. The gray wire on the large white plug to be tapped is just below the blue wire. It can be pulled away from the other wires just enough to attach the tap. The small white plug to the left of the large white plug is the one that is to be removed to plug into the CAN-View box. (This is the MFD connection to the Nav box which will become the MFD connection to the CAN-View.) Then the small white plug on the other CAN-View cable is to be plugged into the Nav plug that was unplugged from the Nav box. (The MFD connection is channeled through the CAN-View and then back out to the Nav box.)

TOYOTA COROLLA ,MATRIX ,TACOMA ,TUNDRA ,PRIUS CRUISE CONTROL KIT INSTALLATION MANUAL

download
BATTERY REMOVAL 1. REMOVE THE REAR FLOORBOARD SHOWN IN FIGURE 1 . 2. REMOVE THE DECK FLOOR BOX REAR SHOWN IN FIGURE 2 . 3. REMOVE THE REAR FLOORBOARD SHOWN IN FIGURE 3 . 4. DISCONNECT THE CABLE FROM THE NEGATIVE TERMINAL OF THE 12 V BATTERY AS SHOWN IN FIGURE 4. CAUTION: ENSURE THAT BATTERY HAS BEEN DISCONNECTED FOR MORE THAN 90 SECONDS PRIOR TO REMOVAL OFAIRBAG ; FAILURE TO HEED THIS WARNING MAY RESULT INAIRBAG DISCHARGE AND MAY CAUSE SERIOUS INJURY OR DEATH . FIGURE 1 FIGURE 2 FIGURE 3 FIGURE 4 PAGE 2 PAGE 3 CONTROL SWITCH LOCATION : RIGHT SIDE STEERING WHEEL COVER 1. DISCONNECT NEGATIVE BATTERY CABLE FROM BATTERY 2. REMOVE A IRBAG BY RELEASING SIDE PANELS FROM STEER – INGWHEELAND EXTRACTING THE TWO 30 TORX SCREWS AS ILLUSTRATED IN FIGURE 5. 3. UTILIZE SMALL SCREWDRIVER TO REMOVE AIRBAGCONNEC – TORS AS ILLUSTRATED IN FIGURE 6. 4. USING THE SWITCH HOLE CUTTING TEMPLATES ON PAGE 15, PLACE THE TEMPLATE ON THE INSIDE OF THE TRIM PIECE AS SHOWN AND DRILL TWO (2) 5 MM (13/64″) HOLES AND ONE (1) 8 MM (11/32″) HOLE . ANOTHER SET OF HOLES WILL NEED TO BE DRILLED FOR TACOMA AND PRIUS FIGURES 8-11.

2007-2009 Toyota FJ Cruiser Banks Monster Exhaust System Installation Manual

download
1. Before starting work, familiarize yourself with the installation procedure by reading all of the instructions. 2. The exploded view (Figure 2) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction. 3. Throughout this manual, the left side of the vehicle refers to the driver’s side, and the right side to the passenger’s side. 4. Disconnect the negative (ground) cable from the battery (or batteries, if there are two) before beginning work. 5. Route and tie wires and hoses a minimum of 6″ away from exhaust heat, moving parts and sharp edges. clearance of 8″ or more is recommended where possible. 6. When raising the vehicle, support it on properly weight-rated safety stands, ramps or a commercial hoist. Follow the manufacturer’s safety precautions. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the front wheels are centered squarely on the topsides; put the transmission in park; set the hand brake; and place blocks behind the rear wheels. Caution! Do not use floor jacks to support the vehicle while working under it. Do not raise the vehicle onto concrete blocks, masonry or any other item not intended specifically for this use. 7. During installation, keep the work area clean. Do not allow anything to be dropped into intake, exhaust, or lubrication system components while performing the installation, as foreign objects will cause immediate engine damage upon start-up. Tools Required: • 1? 2 ” and 3? 8 ” drive ratchets with standard and metric sockets and 1 ? 2 ” and 3? 8 ” drive extension • Standard and metric combination or open-end wrenches • Standard screwdriver • Clean shop towels or rags • Pry-bar Highly recommended tools and supplies: • Foot-pound torque wrench • Penetrating oil or light lubricant spray General Installation Practices 97083 v.2.0 3 Monster Exhaust SySTEM INSTallaTIoN 1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post. 2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground. CaUTIoN: Do NoT WoRK UNDER aNy VEHIClE SUPPoRTED oNly By a JaCK. SEVERE INJURy May RESUlT. 3. From under the vehicle remove the factory exhaust starting at the 2-bolt flange in front of the muffler. Remove the two (2) bolts, two (2) washers, and two (2) springs from the flange and retain for re-use. NOTE: Remove the factory gasket from the 2-bolt flange. The exhaust system will be hanging by the exhaust hanger pins. 4. Liberally apply an aerosol lubricant on all the hanger pins. Remove the exhaust system from the vehicle by removing each hanger pin from the rubber grommet. NOTE: Remove hanger pins from the front of the vehicle to the rear. 5. Drop the exhaust system to the floor and move out of the way. You will not be reusing any components from the exhaust system. 6. Install the Banks conical gasket onto the vehicle’s 2-bolt flange. 7. Install the hanger pin on the intermediate pipe into the corresponding rubber grommet. Install the Banks intermediate pipe onto the factory 2-bolt intermediate pipe outlet using the factory hardware. See Figure 1. When tightening the

Toyota Prius GEN 2 Driver Side Extender Guide Installation Manual

download
Installation Guide: Thank you for purchasing extendmyseat brackets. Please follow the directions carefully and within 30 minutes you will be loving your new seats. Inventory in Box: 2- extendmyseat brackets 4- black 3/8 stainless bolts What you will need for assembly: 1- socket wrench 1- 9/16 socket 1- Metric 13 socket (Prius uses metric bolts however a 9/16 works) 1- 9/16 flat wrench 1- protective eyewear Step 1- Remove the 2 Black extendmyseat brackets from the packaging and locate the 4 black 3/8″ provided bolts. Step 2- Go to your vehicle with a socket wrench and a 9/16 socket, eye protection and your keys. Remember to turn off your cabin lights. Step 3- Locate the 4 factory bolts that hold your drivers seat to the vehicle. Take your socket wrench and loosen the 4 factory bolts. (2 in the front and 2 behind your seat, go to rear seat to locate) Remove the 2 plastic guards to locate the 2 rear factory bolts. Remove the 4 factory bolts and set them aside Step 4- Unplug the 3 factory cables plugged into your car seat under the front portion of the seat. No tools required. Remember to plug these back in after you have completed the install. Step 5- Remove your car seat carefully. (Approx weight is 25 pounds) Step 6- Place your driver’s seat on a bench or on the ground on a clean sheet, towel etc…(don’t want to et it dirty) Step 7- Grab the 2 extendmyseat brackets Step 8- Lay down the 2 black brackets inside your vehicle and line up the 4 hole location. Start with the front 2 holes. Finger tighten the 2 front factory bolts into the 2 front EMS bracket holes. Now line up the 2 rear holes and finger tighten the 2 remaining factory bolts. Finger tighten all 4 holes with seat still out o f the Step 9- place drivers seat back into the vehicle. Line up drivers seat front holes with EMS front holes. Finger tighten front 2 feet with provided EMS bolts. Press seat lever and slide seat to the most up front position. Go to back seat and screw down the remaining 2 factory feet with the factory bolts. Then the 2 remaining EMS bolts into the remaining 2 EMS holes. Place the 3rd EMS bolt into the (B) bracket and the 4th and final bolt into the (A) bracket closest to the outside of the vehicle. Step 10- ONCE ALL 8 BOLTS ARE FINGER TIGHT; NOW COMPLETE THE INSTALLATION BY SECURING THE 8 BOLTS (4 factory and 4 EMS). CHECK TO MAKE SURE ALL 8 BOLTS ARE NOW TIGHT AND SECURE.

Toyota Prius GEN 2 PASSENGER Extender Installation Manual

download
Installation Guide: Thank you for purchasing extendmyseat brackets. Please follow the directions carefully and within 30 minutes you will be loving your new seats. Inventory in Box: 2- extendmyseat brackets 4- black 3/8 x ¾’ stainless grade 8 bolts 1- M10 x 125 by 1.35″ grade 8.8 bolt w/ washer What you will need for assembly: 1- socket wrench 1- 9/16 socket & 1 11/16 SOCKET 1- Metric 13 socket (Prius uses metric bolts however a 9/16 works) 1- 9/16 flat wrench 1- 3/32 allen wrench 1- protective eyewear Step 1- Remove the 2 Black extendmyseat brackets from the packaging and locate the 4 black 3/8″ provided bolts. Step 2- Go to your vehicle with a socket wrench, a 3.32 allen wrench and a 9/16 socket, eye protection and your keys. Remember to turn off your cabin lights. Step 3- Locate the 4 factory bolts that hold your drivers seat to the vehicle. Take your socket wrench and loosen the 4 factory bolts. (2 in the front and 2 behind your seat, go to rear seat to locate) Remove the 2 plastic guards to locate the 2 rear factory bolts. Remove the 4 factory bolts and set them aside Toyota Prius GEN 2 PASSENGER Extender Install Guide Step 4- Unplug the 3 factory cables plugged into your car seat under the front portion of the seat. No tools required. Remember to plug these back in after you have completed the install. Step 5- Remove your car seat carefully. (Approx weight is 25 pounds) Step 6- Place your factory seat on a bench or on the ground on a clean sheet, towel etc…(don’t want to et it dirty) Step 7- Locate the “U” shaped Bracket and loosen the 2 ??? sized bolts. Now locate the (3) 3/32 steel screws and unscrew. Toyota Prius GEN 2 PASSENGER Extender Install Guide The “U” shaped bracket should come out of the vehicle. This part is not necessary or controls any of the vehicles functions. Hold on to this however you will not need it to complete the installation. Step 7- Grab the 2 extendmyseatbrackets Toyota Prius GEN 2 PASSENGER Extender Install Guide Step 8- Lay down the 2 black EMS brackets inside your vehicle and line up the 4 hole locations. Start with the front 2 holes. Almost tighten the 2 front factory bolts into the 2 front EMS bracket holes. The (1) M10 bolt provided will be used on the hole facing the inside of the vehicle in the rear of bracket B. You will need this longer bolt to connect the EMS bracket the factory rear hole location. For the 4th factory hole, line up the last remaining rear hole on bracket A rear.