Skip to content

2011 toyota tacoma shop manual

You search PDF repair manual about 2011 toyota tacoma shop manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 TOYOTA TACOMA SUPERCHARGER FIT KIT INSTALLATION MANUAL

download
TOYOTA TACOMA MY 2005- SUPERCHARGER FIT KIT Procedure Page 5 of 46 pages Issue: E 11/04/08 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). • The TIS Repair Manual can be referenced for additional details. Please see your Toyota dealer for a copy of this document. 1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 7, save this coolant as it will be reused. CAUTION: To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause the hot engine coolant and steam to blow out from the radiator. (h) All parts that are removed and not reused should be saved for the customer, i.e., “discard” means to save for the customer.

Toyota Tacoma extra cab Rear Jump Seats Installation Manual

download
INSTRUCTION Toyota Tacoma extra cab Rear Jump Seats Dear Customer, As we are unable to assist you on installing your Wet Okole Hi. Waterproof sport seat covers we offer these special instructions. This particular instruction is a universal instruction for Toyota Tacoma rear bench. Mostly all other vehicles are self explanatory. Any problems please feel free to call for technical support at 1(888)24-Okole. Enjoy your Wet Okole Hawaii Seat Covers! Step1 Step2 Next: With a pair of dull plastic pry tools ora pair of butterknives pry the rest cushion up with one tool and tuck seat cover under rest cushion with the other. Fold both seat cushions forward and slip seat cover over cushion and attach velcro. Note: Rear plastic rest may need to be removed from vehicle to allow easy seat cover installation. Note: Tuck cover underneath plastic. Note: Backrest panel maybe removed by pulling panel off of rear cab, there are 6 plastic plugs on the back of the panel that snap into the rear firewallofthecab.

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

TOYOTA COROLLA ,MATRIX ,TACOMA ,TUNDRA ,PRIUS CRUISE CONTROL KIT INSTALLATION MANUAL

download
BATTERY REMOVAL 1. REMOVE THE REAR FLOORBOARD SHOWN IN FIGURE 1 . 2. REMOVE THE DECK FLOOR BOX REAR SHOWN IN FIGURE 2 . 3. REMOVE THE REAR FLOORBOARD SHOWN IN FIGURE 3 . 4. DISCONNECT THE CABLE FROM THE NEGATIVE TERMINAL OF THE 12 V BATTERY AS SHOWN IN FIGURE 4. CAUTION: ENSURE THAT BATTERY HAS BEEN DISCONNECTED FOR MORE THAN 90 SECONDS PRIOR TO REMOVAL OFAIRBAG ; FAILURE TO HEED THIS WARNING MAY RESULT INAIRBAG DISCHARGE AND MAY CAUSE SERIOUS INJURY OR DEATH . FIGURE 1 FIGURE 2 FIGURE 3 FIGURE 4 PAGE 2 PAGE 3 CONTROL SWITCH LOCATION : RIGHT SIDE STEERING WHEEL COVER 1. DISCONNECT NEGATIVE BATTERY CABLE FROM BATTERY 2. REMOVE A IRBAG BY RELEASING SIDE PANELS FROM STEER – INGWHEELAND EXTRACTING THE TWO 30 TORX SCREWS AS ILLUSTRATED IN FIGURE 5. 3. UTILIZE SMALL SCREWDRIVER TO REMOVE AIRBAGCONNEC – TORS AS ILLUSTRATED IN FIGURE 6. 4. USING THE SWITCH HOLE CUTTING TEMPLATES ON PAGE 15, PLACE THE TEMPLATE ON THE INSIDE OF THE TRIM PIECE AS SHOWN AND DRILL TWO (2) 5 MM (13/64″) HOLES AND ONE (1) 8 MM (11/32″) HOLE . ANOTHER SET OF HOLES WILL NEED TO BE DRILLED FOR TACOMA AND PRIUS FIGURES 8-11.

2007-2009 Toyota FJ Cruiser Banks Monster Exhaust System Installation Manual

download
1. Before starting work, familiarize yourself with the installation procedure by reading all of the instructions. 2. The exploded view (Figure 2) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction. 3. Throughout this manual, the left side of the vehicle refers to the driver’s side, and the right side to the passenger’s side. 4. Disconnect the negative (ground) cable from the battery (or batteries, if there are two) before beginning work. 5. Route and tie wires and hoses a minimum of 6″ away from exhaust heat, moving parts and sharp edges. clearance of 8″ or more is recommended where possible. 6. When raising the vehicle, support it on properly weight-rated safety stands, ramps or a commercial hoist. Follow the manufacturer’s safety precautions. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the front wheels are centered squarely on the topsides; put the transmission in park; set the hand brake; and place blocks behind the rear wheels. Caution! Do not use floor jacks to support the vehicle while working under it. Do not raise the vehicle onto concrete blocks, masonry or any other item not intended specifically for this use. 7. During installation, keep the work area clean. Do not allow anything to be dropped into intake, exhaust, or lubrication system components while performing the installation, as foreign objects will cause immediate engine damage upon start-up. Tools Required: • 1? 2 ” and 3? 8 ” drive ratchets with standard and metric sockets and 1 ? 2 ” and 3? 8 ” drive extension • Standard and metric combination or open-end wrenches • Standard screwdriver • Clean shop towels or rags • Pry-bar Highly recommended tools and supplies: • Foot-pound torque wrench • Penetrating oil or light lubricant spray General Installation Practices 97083 v.2.0 3 Monster Exhaust SySTEM INSTallaTIoN 1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post. 2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground. CaUTIoN: Do NoT WoRK UNDER aNy VEHIClE SUPPoRTED oNly By a JaCK. SEVERE INJURy May RESUlT. 3. From under the vehicle remove the factory exhaust starting at the 2-bolt flange in front of the muffler. Remove the two (2) bolts, two (2) washers, and two (2) springs from the flange and retain for re-use. NOTE: Remove the factory gasket from the 2-bolt flange. The exhaust system will be hanging by the exhaust hanger pins. 4. Liberally apply an aerosol lubricant on all the hanger pins. Remove the exhaust system from the vehicle by removing each hanger pin from the rubber grommet. NOTE: Remove hanger pins from the front of the vehicle to the rear. 5. Drop the exhaust system to the floor and move out of the way. You will not be reusing any components from the exhaust system. 6. Install the Banks conical gasket onto the vehicle’s 2-bolt flange. 7. Install the hanger pin on the intermediate pipe into the corresponding rubber grommet. Install the Banks intermediate pipe onto the factory 2-bolt intermediate pipe outlet using the factory hardware. See Figure 1. When tightening the