2013 f350 side mirror disassembly

You search PDF repair manual about 2013 f350 side mirror disassembly, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2013 f350 side mirror disassembly Direct Download speed 5432 Kb/s

  2013 f350 side mirror disassembly Full Version speed 8172 Kb/s



Toyota Sequoia SR5 2001-2006, Toyota Tundra 2000-2006, Toyota Tundra D-Cab 2005-2006 Signal Mirror Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
1. Open the driver side door and lower the window. 2. Remove the door panel, kick panel, and plastic trim piece along the bottom of the door frame. 3. Disconnect the mirror wire harness. Remove the three mirror mounting nuts and remove the mirror housing from the vehicle. 1 2 3 Mirror Replacement – 2 – 4 There is a plug seated in a socket in the center of the mirror that holds the mirror in the mirror housing. Lift up the inboard edge of the mirror. Use a small pry bar and pry up around the center of the mirror until the plug unseats from the socket. 5 There are two drive pins on the bottom and outboard sides of the mirror. Hold the top of the mirror away from the mirror housing and pry away the bottom drive pin from the back of the mirror. 6 Hold the inboard side of the mirror away from the mirror housing and pry away the outboard drive pin from the back of the mirror. IF heated, disconnect OE heater wire from heater terminals. Note: During the removal of the original mirror, if motor pins stay attached to the back plate, use “V” end in small pry bar or needle nose pliers to disengage pins from back plate. Set the mirror aside. 7 8 Using the shorter of the two harnesses from the kit, tape the end without the mating connector to the end of the gopher wire. Remove the foam insulation from the mirror housing sail. Starting from the inside of the mirror housing, guide a piece of gopher wire down alongside the existing factory wire harness and out of the bottom of the mirror housing sail. 9 Pull the gopher wire and wire harness through the mirror housing until about 4 inches of wire remain inside the mirror housing.
13 Tuck the wire harness behind the Signal® mirror. Insert the other drive pin into the outboard pin socket (socket closest to the optic module). Align the socket in the center of the Signal® mirror over the plug on the center of the mirror mount. Align drive pins to its mating slots on the motor mount and vice-versa. Anti-vibration tab should be tucked inside housing. 14 Use the palm of your hand and firmly press down on lower portion (marked boundaries) of the Signal® mirror until it snaps into position. Press down carefully on the mirror outboard edge to engage outboard drive pin into mirror mount socket. 15 Press mirror down carefully on the lower edge to engage the lower drive pin into motor mount. Remount mirror to door, then use Electronic Hand Control to relocate mirror position. Gently clean any finger mark/dirt away from mirror using paper towel and glass cleaner. 10 Guide the Signal® mirror harness along the existing path of the factory wire harness and through the foam insulation. Remove any slack in the wire. Reposition the foam insulation on the mirror housing sail. 11 Connect the Signal® mirror mating connector to the Signal ® mirror harness. If heated , reconnect the heater wires to the heater terminals on the back of the new Signal® mirror. NOTE: There is no polarity so the wires may be interchanged. Disregard heater connections on vehicles not equipped with outside heated mirrors. 12 The drive pins must be aligned before installing the Signal® mirror. If needed, insert a drive pin into the lower socket on the mirror mount. Align the nubs on the lower drive pin so it points to the round plug in the center of the mirror mount.

Related Content:

how to access to wiring harness for radio on 2006 Buick Lucerne, 2006 malibu door wiring diagram, Saturn ION-2 2 2 L4 GAS Wiring Diagram, Repairing a ford F-150 side mirror 2011, repair link pins on Tundra 2000, OnStar FMV Wiring Instructions, mirror glass removal f150, how to replace heated power mirror glass 2004 ford f150, how to remove a side mirror from a 1994 ford f150 truck, 2000 mercury cougar drivers side mirror free replacement instructions

2007-2008 Toyota Camry Signal Mirror Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 24-10-2011

download
REMOVE BATTERY CABLE 1. Protect fender before starting. Do not touch the positive terminal with any tool when removing cable. Remove the negative battery cable…. 1. Open driver side door. Lower window. Remove plastic cover on door handle. Remove (2) screws revealed by the removal of the handle cover. (Fig. 2 (Fig. 2 (Fig. 2 (Fig. 2—-1) 1) 1) 1) DOOR PANEL REMOVAL DOOR PANEL REMOVAL DOOR PANEL REMOVAL DOOR PANEL REMOVAL 2. Remove plastic cover within door release lever. Remove screw behind plastic cover. Remove upper right hand corner cover plate. (Fig. 2 (Fig. 2 (Fig. 2 (Fig. 2—-2) 2) 2) 2) 3. With a 7/16 T-Handle, slowly push in the center of the rivet to disengage rivet from door frame (rivets located around the CAUTION: CAUTION: CAUTION: CAUTION: These rivets are fragile These rivets are fragile These rivets are fragile These rivets are fragile and break easily. removing these rivets. (Fig. 2 rivets. (Fig. 2 rivets. (Fig. 2 rivets. (Fig. 2—-3) 3) 3) 3) 4. Slowly pull to disengage the door panel. Pull door panel out slightly, disconnect wiring behind door panel light [located on the lower left hand corner]. (Fig. 2 (Fig. 2 (Fig. 2 (Fig. 2—-4) 4) 4) 4) 5. Lift door panel and pull it out partially. Unsnap door lever rod behind door panel. Remove door panel and set it aside. Disconnect mirror harness. Secure the mirror housing with one hand, remove the (3) nuts holding the mirror housing to the door WARNING:

Related Content:

2001 chevy impala code p0446

2007-2008 Toyota Tundra Crew Cab Installation Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware with a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper re-installation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners located on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. A5a A5b 2007-08 Toyota Tundra Crew Cab By Gilbert R. Gutierrez Vehicle type: Four-door, crew-cab pickup truck NAGS numbers*: Windshield part numbers are FW02724, FW02723, FW02722 or FW02721; front door glass FD23323- 24 R-L; rear door glass FD23325-26 R-L; and back glass FY95054, FY95053, FB23336, FB23335 and FB23334. Helpful tools or supplies: Retention tape or a rubber hose to protect the fenders and hood; a PryBaby for molding and panel removal. Watch for: Be careful not to pull too hard on the rearview mirror harness during removal to avoid ripping the headliner. When removing or re-installing the A-pillar trim panels, take care to avoid disturbing the curtain air-bag harness. *With permission from National Auto Glass Specifications. Call NAGS at 800/551-4012 or visit www.nags.com. Vehicle information A1 A2 A3a A3b A4a A4b 35 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, and then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool to cut out the glass, remove the A-pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to dis- A6a A6b A6c A7a A11a A11b A12a A12b A7b A7c A8 A10 A13a A13b 36 AutoGlass™ •March/April 2008 Installation ? F or T echnicians Only turb the curtain air-bag harness when removing or re-installing the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers. Removal 14. Make sure cutting blades are sufficiently sharp. 15. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane. 16. If using a cold knife, use a 3? 4 -inch blade. Cut three sides; then use a long knife or power tool to cut the bottom of the windshield. Note: There are no gravity stops on this windshield. 17. If trying to save the windshield, use an Equalizer with an 8-inch blade. Note: When using any power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts. 18. After cutting the sides and top, cut out the bottom portion of the glass using an Equalizer Express. Spray the bottom of the windshield with water at least 4-to-5 inches above the urethane on the glass, so the water flows down into the urethane while you make your final cut across the bottom of the windshield. Caution: Never use your head to push, as this could result in back and neck injuries. 19. Take the windshield out of the opening using a set of vacuum cups. Lift the glass and place it on a windshield stand or suitable workstation. Installation 20. After cutting the windshield out, remove contaminants such as dirt, moisture and other debris from the pinchweld. Clean the dashboard. 21. Dry fit the new glass to the opening. Mark your glass using a grease pencil or molding-retention tape. 22. Place your vacuum cups on the windshield in the appropriate location for a one-person set. 23. For driver-side setting of the windshield using a Glass Handler Kit, place the kit’s elbow-setting pad on the driver’s side of the hood area; then lift the windshield from the stand using the vacuum cups. 24. Reach over, place your elbow on the setting pad and set the windshield onto the old urethane. 25. With the windshield resting in the opening, make sure it is in the right spot. 26. Adjust both sides to the correct setting, marking the passenger’s side, then the driver’s side. Lift the glass and place it on a windshield stand or suitable workstation. 27. Follow the urethane manufacturer’s recommendations for installation. 28. Clean the inside of the windshield using a urethane manufacturer-recommended product; follow recommended steps. Note: Do not touch the bonding area of the windshield after cleaning, prepping or priming it. 29. Wear powder-free Nitrile gloves to keep off chemicals. 30. Apply the glass prep and primer, following the urethane manufacturer’s recommendations.

Related Content:

ford 4500 backhoe parts radiator with oil cooler, fender removal 06 tundra, 2007 toyota tundra dash removal, INSTALLING FJ CRUISER WINDSHIELD, change out connector and pump for windsheild wash reservoir in 1990 Buick LeSabre, how to remove inside front windshield pillar molding 2013 escalade, how to remove tundra power seat switch, lincoln navigator windshield seal, repair windshield wiper arm on 2003 buick lesabre custom, silverado low washer fluid

2005 TOYOTA AVALON TVIP V4 (REMOTE ENGINE STARTER) INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 2 of 33 pages Issue: C 02/02/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Visassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly if equipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process. FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Step g) NOTE: Do not perform this step if the vehicle has Smart Entry. (g) Remove the driver’s step cover. (Fig. 1-7) Screw Fig. 1-5 10mm Wrench, Phillips Screwdriver Bolt Glove Box Assembly Cowl Cover Fig. 1-4 Nut Fig. 1-6 Nylon Panel Removal Tool, Phillips Screwdriver Screws (x3) Glove Box Assembly Trunk Opener Cancel Switch Connector Fig. 1-7 Step Cover Nylon Panel Removal Tool
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 4 of 33 pages Issue: C 02/02/05 FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Steps h-l) NOTE: Do not perform this step if the vehicle has Smart Entry. (h) Remove the driver’s cowl cover. (Fig. 1-8) (1) Remove the one nut securing the cowl cover. (i) Remove the hood release cable. (Fig. 1-9) (1) Do not bend the hood release cable. (j) Open the screw cover on the lower dash cover. Insert the tip of a Nylon Panel Removal Tool in the upper slot to loosen it. (Fig. 1-9) (1) Remove one screw and one bolt securing the lower dash cover. (k) Remove the lower dash cover. (Fig. 1-10) (1) Disconnect the temperature sensor (connector and aspirator hose) from the lower dash cover if equipped. (l) Carefully remove the driver side airbag assembly. (Fig. 1-11) (1) Remove four bolts securing the driver side airbag assembly. (2) Be careful not to get cut by the sharp metal edges. (3) Do not disconnect the airbag assembly. (4) Use the empty V4 kit box to support the airbag assembly on the floor

Related Content:

Prius upper glovebox door hinge, Prius repair glovebox door, toyota venza glove compartment box, how to take the back off a blu dask 3 5, colbalt where is the strarter located, 2005 toyota tacoma airbag fuse location, 2005 toyota corolla under carriage, clicking noise by glove box 2008 chevy impala, loud clicking noise in glove box impala, PICTURE OF GLOVE BOX LOWER BRACE ON CHEVY UPLANDER

2008 HONDA ACCORD 2- AND 4-DOOR AUTOMATIC DAY/NIGHT MIRROR (LX) INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 08-10-2011

download
INSTALLATION 1. Make sure you have the anti-theft code for the radio, then write down radio station presets. 2. Disconnect the negative cable from the battery. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 7214110E AUTOMATIC DAY/NIGHT MIRROR AUTOMATIC DAY/NIGHT MIRROR HARNESS 3. Disengage the eight retaining tabs and remove the left and right lenses from the roof console. Without Moonroof: With Moonroof: 7302010B ROOF CONSOLE RIGHT LENS 4 RETAINING TABS LEFT LENS 4 RETAINING TABS SHOP TOWEL FLAT-TIP SCREWDRIVER 761802AB ROOF CONSOLE RIGHT LENS 4 RETAINING TABS LEFT LENS 4 RETAINING TABS SHOP TOWEL FLAT-TIP SCREWDRIVER Open the sunglass holder. 5. Remove the four screws (two black and two silver) and let the roof console drop down. Disconnect the vehicle connectors and remove the roof console. Without Moonroof: With Moonroof: 730202AB BLACK SCREWS ROOF CONSOLE SUNGLASS HOLDER (Open. ) SILVER SCREWS VEHICLE CONNECTORS 761803AB ROOF CONSOLE SUNGLASS HOLDER (Open. ) VEHICLE CONNECTORS BLACK SCREWS SILVER SCREWS 6. Turn the sunvisor holder 45°, and remove the two sunvisor holders. 7. Turn the left sunvisor toward the driver’s seat. 8. Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.

TOYOTA DASH DISASSEMBLY INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 11-04-2012

download
Disconnect the negative battery terminal to prevent an accidental short circuit. 1 Unclip and remove side panel from both sides of radio and climate controls. Figure A) 2 TOYOTARAV 42001-2005 Remove (4) Phillips screws securing the radio/climate control trim panel. (Figure B) 3 Remove (4) 10 MM bolts securing the radio. (Figure C) 4 DASH DISASSEMBLY A B C Continue to kit assembly. Unplug and remove radio. 5 Remove factorybrackets from radio. Retain brackets for use during kit assembly. 6 7 95-8202 DASH DISASSEMBLY TOYOTAMR2 SPIDER 2000-2005 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap the lower trim piece from each side of the dash console and remove (2) Phillips screws exposed in each cavity. Remove the upper trim piece from each side of the console. (Figure A) 2 Remove the climate control knobs and (2) Phillips screws exposed. Remove the climate control trim bezel. (Figure A) 3 Remove the ashtray and (1) 10mm bolt exposed. Unclip the ashtray trim bezel and remove. (Figure A) Unclip the radio trim bezel, remove (4) Phillips screws securing the unit and disconnect the wiring. 4 1 5 2 A Continue to kit assembly. 7

2001 Mazda Truck MPV FRONT DOOR DISASSEMBLY/ ASSEMBLY

0

Filed Under (Mazda Manuals) by admin on 12-06-2011

download
1. Lower or raise the front door glass so that the distance from the top of the front door glass at the rear end to the upper part of the front molding is 185 mm {7.3 in} 2. Disconnect the negative battery cable. 3. Remove the front door trim 4. Disassemble in the order indicated below. 1. Inner handle 2. Front door trim bracket 3. Door screen 4. Front door glass 5. Front manual window regulator 6. Front power window regulator 7. Glass run channel 8. Front door lock 9. Outer handle 10. Door key cylinder 11. Door weatherstrip 12. Door lower weatherstrip 5. Assemble in the reverse order of disassembly Front Door Glass Disassembly Note 1. Remove the front door glass installation bolts. 2. Slant the front door glass as shown, and remove the front door glass from the inside of the front door. Outer Handle Assembly Note 1. Connect the door key cylinder harness of outer handle as shown

2007-2008 Toyota Tundra Extended Cab Installation Manual

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
windshield Preparation 1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware using a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper reinstallation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three fasteners on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool for cutout, remove the A- pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby tool. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to disturb the curtain air-bag harness when removing or reinstalling the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers

Renault Laguna II A195 Door function control module driver

0

Filed Under (Renault Manuals) by admin on 13-01-2012

download
Battery – 30 Battery + A195 Door function control module, driver A196 Door function control module, passenger M27 Door mirror adjustment motor, driver M28 Door mirror adjustment motor, passenger S98 Door mirror adjustment switch EP10Earth point location 10 EP4 Earth point location 4 EP5 Earth point location 5 EP9 Earth point location 9 M14 Electric window motor, driver M15 Electric window motor, passenger S64 Electric window switch, driver’s door S65 Electric window switch, passenger door F Fuse X28-IIFuse box/relay plate, engine bay X28-IFuse box/relay plate, fascia 1 K79 Ignition main circuits relay 15 Ignition switch – ignition ON A11 Multifunction control module X92 Shorting link connector bl = blue br = brown el = cream ge = yellow gn = green gr = grey nf = neutral og = orange rs = pink rt = red sw = black vi = violet ws = white hbl = light bluehgn = light green rbr = maroon x = braided cabley = high tensionz = non-cable connection NOTE: In certain diagrams (Citroen, Peugeot & Renault), colour codes are replaced by numbers which are used to identify a particular cable and not the colour. In this instance, the cables will be numbered at each end close to the harness connector.

Related Content:

renault laguna no ingntion, renault laguna relays

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

0

Filed Under (Chevrolet Manuals) by admin on 29-12-2011

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

Related Content:

2005 taurus exhaust system diagram, 2 2 s10 exhaust flange bolts, diagram of an exhaust system on a 2003 gmc envoy, Diagram of a exhaust crossover pipe for a 95 Oldsmobile aurora, 04 pacifica parts diagram, pontiac sunfire gt exhaust system diagram, how tight should exhaust, gmc yukon exhaust manifold diagram, 454 exhaust donut installation, 2006 corvette mid pipe flange torque

Related Content:

how to access to wiring harness for radio on 2006 Buick Lucerne, 2006 malibu door wiring diagram, Saturn ION-2 2 2 L4 GAS Wiring Diagram, Repairing a ford F-150 side mirror 2011, repair link pins on Tundra 2000, OnStar FMV Wiring Instructions, mirror glass removal f150, how to replace heated power mirror glass 2004 ford f150, how to remove a side mirror from a 1994 ford f150 truck, 2000 mercury cougar drivers side mirror free replacement instructions