Skip to content

4t60e repair manual

You search PDF repair manual about 4t60e repair manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Pontiac Bonneville V6-3.8L VIN K – A/T 4T65E Harsh Shifts/Shudders/Slips Repair Manual

download
Line Pressure Check Procedure Tools Required Important: Before performing a line pressure check, verify that the pressure control (PC) solenoid valve is receiving the correct electrical signal from the PCM. Caution: Keep the brakes applied at all times in order to prevent unexpected vehicle motion. Personal injury may result it the vehicle moves unexpectedly. J 21867Universal Pressure Gauge Set 1. Install a Scan Tool. 2. Start the engine and set the parking brake. 3. Check for a stored Diagnostic Trouble Code (DTC). 4. Repair the vehicle, if necessary. 5. Check the fluid level. Refer to the Transmission Fluid Checking Procedure. 6. Check the manual linkage for proper adjustment. 7. Turn the engine OFF. Remove the oil pressure test hole plug and install the J 21867. 8. Put the gear selector in PARK range and set the parking brake. 9. Start the engine and allow the engine to warm up at idle Notice: Total test running time should not be longer than two minutes, or else transmission damage could occur. Notice: Refer to Fastener Notice in Cautions and Notices. Parts Information 10. Access the PC solenoid valve control test on the Scan Tool. Zoom Sized for Print 11. Increase the PC solenoid as shown actual current from 0.0 to 1.0 amps in 0.1 amp increments. Allow the pressure to stabilize for five seconds after each pressure change. Read the corresponding line pressure on the J 21867. 12. Refer to the Line Pressure specification table. Compare the data to the table. 13. If pressure readings differ greatly from the table, refer to Incorrect Line Pressure. 14. Remove the J 21867. 15. Apply sealant, P/N 12345382 (in Canada, P/N 10953489), to the oil pressure test hole plug. 16. Install the oil pressure test hole plug. Tighten Tighten the oil pressure test hole plug to 12 N.m (106 lb in).

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

HONDA Accord V6, Odyssey, Pilot Idle Vibration or Harsh Shifting Repair Manual

download
SYMPTOM There is a vibration at idle or harsh engagement when shifting the transmission between between Park, Drive, and Reverse. PROBABLE CAUSE The front hydraulic engine mount may have deteriorated and torn. PARTS INFORMATION Front Engine Mount Assembly: 1998-02 Accord V6 – P/N 50810-S87-A82, H/C 7981657 1999-04 Odyssey – P/N 50800-S0X-A04, H/C 7978927 2003-05 Pilot – P/N 50800-S3V-A82, H/C 7984560 WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Failed Part: P/N 50810-S87-A81 H/C 5438593 Defect Code: 01102 Symptom Code: 04501 Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. DIAGNOSIS 1. Bring the engine up to operating temperature, and fully apply the parking brake. 2. Have an assistant view the top of the front engine mount while standing to the side of the vehicle. Shift the transmission to Drive. With your foot firmly on the brake pedal, quickly depress the accelerator pedal and release it. Your assistant should look for contact between the top of the engine mount and the bottom of the front engine mount bracket, and listen for noise from that area. REPAIR PROCEDURE 1. Drive the vehicle onto a lift, but do not raise it. 2. Odyssey – Remove the intake manifold cover and the front ignition coil cover: •See page 9-4 of the 1999-04 Odyssey Service Manual. •Online, enter keyword INTAKE , and select Intake Manifold Removal and Installation from the list. 3. Odyssey – Remove the radiator cover: •See page 10-16 of the 1999-04 Odyssey Service Manual. •Online, enter keyword RADIATOR , and select Radiator and Fan Replacement from the list