pontiac grand prix 400ci vacuum diagram

You search PDF repair manual about pontiac grand prix 400ci vacuum diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  pontiac grand prix 400ci vacuum diagram Direct Download speed 5432 Kb/s

  pontiac grand prix 400ci vacuum diagram Full Version speed 8172 Kb/s



1998-2000 HONDA Accord L4 Replace the fuel pressure regulator, and reroute the fuel pressure regulator vacuum line

0

Filed Under (Honda Manuals) by admin on 16-07-2012

download
1. Locate and identify the three vacuum ports on the intake manifold. 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A M/T WITH CRUISE CONTROL 2. Disconnect and discard the vacuum hose that connects the fuel pressure regulator to vacuum port C. 3. Plug vacuum port C with the cap from the tube kit. 4. Replace the fuel pressure regulator. Refer to page 11-113 of the 1998-00 Accord Service Manual. 5. Install the new vacuum hose kit using one of the following procedures. Zoom Sized for Print 1. Remove and discard the cap from vacuum port A. 2. Connect the short vacuum hose to vacuum port A. Zoom Sized for Print 3. Anchor the long vacuum hose by attaching it to the rear intake air duct clip and to the cruise control hose. . Route the new vacuum hose to the fuel pressure regulator. Attach the hose to the three rear clips on the engine wire harness cover. Zoom Sized for Print 1. Remove and discard the vacuum hose from vacuum port A. This hose supplies vacuum to the rear engine mount control solenoid. 2. Connect the short vacuum hose from the top of the Y fitting to vacuum port A

Related Content:

1993 Corvette Service Manual PDF, vent line 1998 mercy sable, VACUUM LINES ON A 2003 GM 6 CLINDER, vacume lines on 2004 pt cruiser gt, What color is the tcc solenoid in toyota sequoia, 2002 2 4L olds alero vacuum hose routing diagram, ford taurus 2001 engine vacuum hoses on intake, pt cruiser vacuum system diagram, vaccum lines 2001 pt cruiser, Does a volvo d12 engine require silicone or gasket between engine and flywheel housing

1984-1995 Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System Repair Manual

0

Filed Under (Honda Manuals) by admin on 22-04-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum. When servicing or repairing any part of the emissions system, it is absolutely essential to check for any obvious mechanical faults or failures. Remember, a trouble code only indicates which sensor or circuit is affected by the problem. Simple mechanical faults such as a vacuum leak or poor electrical connection can cause a fault code. The EGR valve is not simply open or closed but is modulated by controlling the amount of engine vacuum to the valve diaphragm, up to a maximum of 8 in. Hg of vacuum. The EGR valve has a sensor in the top of the valve that reports valve lift to the ECU (same as ECM, 1992-95). The ECU modulates the position of the control solenoid valve to control the EGR valve lift according to an internal program. Upstream of the control solenoid valve, the CVC provides a constant supply of vacuum so EGR control is precise under all manifold vacuum conditions

Related Content:

2004 honda purge control valve, c230 2005 removing pcv valve and hoses, clean egr valve lincoln, 2008 hyundai elantra purge valve, where is the pcv valve on chevy cruze, egr valve chevy trailblaxer 2005, pvc valve for 2001 merc sable 24 valve overhead cam, 2007 implala vent solenoid replacement, where is the pvc valve located on a 2008 toyota tundra, fuel purge valve for 2006 chevy impala

EDELBROCK PERFORMER SERIES CARBURETORS INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 27-12-2011

download
Figure 1 – Fittings and Vacuum Port Locations INSTALLATION PROCEDURE BEFORE REMOVING OLD CARBURETOR 1. Determine if the distributor vacuum port is timed (no vacuum at idle) or full (vacuum present at idle). With the engine at operating temperature and idling, pull the vacuum advance hose off of the carburetor and “feel”for vacuum by putting your finger on the vacuum port (See Fig. 2) . If your distributor has timed vacuum advance, you will hook the vacuum hose from the distributor to the passenger side vacuum port on the new carburetor. If it has full vacuum advance, it will be hooked up to the driver side port. 2. The stock steel fuel line must be converted to fuel resistant rubber hose. The stock steel line will not connect to the Performer Series Carburetor. Use Edelbrock Universal Fuel Line Kit #8135. This kit contains a filter, neoprene hose, and fittings to adapt to 5/16″or 3/8″stock steel fuel lines (See Fig. 3) . NOTE: After cutting the steel line, remove sharp edges and clean out any chips. 3. Always use a new fuel filter. Failure to do so will void your warranty. 4. You must use Edelbrock Adapter #2696 or Adapter & Fuel Line Kit #2697 when installing a Performer Series carburetor on a General Motors Quadrajet or Chrysler Thermoquad intake manifold. #2697 includes adapter #2696 and fuel line kit #8135. Do not use an open adapter! (See Fig. 4) 5. You must use Edelbrock Adapter #2732 when installing a Performer Series carburetor on certain Edelbrock intake manifolds. In those applications, install the adapter as shown (See Fig. 5)

Related Content:

edelbrock carburetor repair guide, edelbrock edl 1406 overhaul manual, quicksilver carb instructions, Throttle springs Carter Thermo Quad

2002 Mercury Sable Upper Intake Manifold Removal And Installation Manual

0

Filed Under (Mercury Manuals) by admin on 11-02-2012

download
Upper Intake Manifold Removal 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. Zoom Sized for Print 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. Zoom Sized for Print 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1. Position new gaskets in the upper intake manifold. 2. Position the upper intake manifold and install the bolts in the sequence shown. 3. Install the EGR vacuum regulator valve. 4. Install the EGR valve. Zoom Sized for Print 1 Position the valve. 2 Install the bolts. 3 Connect the electrical connector. 4 Connect the vacuum hose. Zoom Sized for Print 1 Position the EGR. 2 Install the bolts. 3 Install the nuts 4 Connect the vacuum hose

Related Content:

quicksilver throttle control manual

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 saturn sl1 owners manual, 2000 buick century service manual free, 560sl repair 1988, 2000 buick lesabre service manual pdf, 2000 buick lesabre repair manual free pdf download, diagrama buick century 2002 pmc, Diagram of us system old mobile intrigue, park avenue ac control schematic

Toyota Matrix XRS Air Intake Removal And Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 10-02-2011

download
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the mass air sensor electrical connection. 3. Remove the screw that secure the vacuum switching valve to the air cleaner. 4. Remove the stock bracket from the vacuum switching valve. 5. For 2005 and 2006 models, you need to unclip the vacuum switching valve hose from the intake tube, and remove the screw from PWM switching valve. 6. Loosen the clamps at the throttle body and at the air cleaner, then remove the stock intake tube. 7. For 2002 to 2004 models, you need to remove the EVAP OBD canister closed valve vent from the air cleaner. Then unclip the upper air cleaner, then tilt upwards to unclip the PWM vacuum switching valve and the vacuum hose. 8. For 2005 and 2006 models, unclip vacuum switching valve hoses from air box, then unclip the PWM switching valve wire harness from upper airbox. 9. Remove the upper Air cleaner. 10. For 2002 to 2004 models, loosen and remove the bolt that secure the EVAP OBD canister closed valve to the lower air cleaner. 11. Loosen and remove the three bolts that secure the lower air cleaner, then disconnect the vacuum hose from the butterfly valve. 12. Tilt the lower air cleaner upwards to unclip the wire harness. 13. Remove the lower air cleaner. 14. Loosen the battery hold down bracket. 15. Remove the bolt that secures the battery hold down bracket to the radiator core support, then remove the battery hold down bracket. 16. Remove the push clip that secures the air inlet duct to the radiator core support. 17. Loosen and remove the bolt that secures the air inlet duct to the inner fender. 18. Tilt that battery backwards, then remove the air inlet duct. 19. Reinstall the battery hold down bracket. 20. Disconnect two vacuum hoses from the vacuum switching valve. Install of Intake

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

1984-1995 Honda Accord/Prelude In­Tank Fuel Pumps TEST/REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 03-07-2012

download
Carbureted Fuel System GENERAL INFORMATION On these vehicles, the engine management system is considered part of the emission control system. The major components include the carburetor(s), feedback control system, the air injection system, a throttle control system and the EGR system. The system consists of sensors and switches that feed information to the Electronic Control Unit (ECU), which will then operate several solenoid valves to maintain the ideal air/fuel ratio under all conditions. As useful as the tests found in this section are, the first step in repair or service to engine management systems is still to gain as much information as possible about the problem; when and under what conditions it occurs. At highway speed? At idle only? Only under heavy load or hard acceleration? Wet weather? Defining the problem will eliminate many systems from consideration and possibly point to the affected system. Before diving into an extended electrical diagnosis, take the time to review the basics. Check every vacuum line for cracks or leaks. Check every electrical connector for corrosion or loose pins. Quite often, simply unplugging and reconnecting a connector will break up corrosion on the pins and restore the circuit. Watch out for poor grounds, particularly if the car has experienced major bodywork. COMPONENT TESTING Air Injection System The purpose of this system is to supply oxygen to the exhaust stream at a point in the exhaust manifold that is hot enough to burn off some of the hydrocarbon emissions. The main component is an air suction valve. The valve is spring loaded to stay closed, with engine vacuum supplied to a diaphragm that reduces the spring pressure and allows the reeds to open. The ECU regulates the engine vacuum to the diaphragm by operating a solenoid valve. 1. With the engine at normal operating temperature and at idle, remove the air cleaner and listen for a bubbling sound at the air suction port. There should be no sound at idle, meaning the air suction valve is closed. 2. If the noise is heard at the air suction port, disconnect the vacuum hose at the air suction valve and connect a vacuum gauge to the hose. There should be no vacuum. If there is vacuum and the noise stops, the problem is in the control system. If there is no vacuum and the bubbling sound is still there, the air suction valve is defective and must be replaced. 3. To test the valve, draw a vacuum at the air suction valve diaphragm and listen for a bubbling sound at the air suction port. If no sound is heard, the air suction valve or diaphragm is faulty. Throttle Control System

Related Content:

Honda Automotive Electrical Connectors Replacement

Honda Civic/ CRX Positive Crankcase Ventilation (PCV) System OPERATION MANUAL

0

Filed Under (Honda Manuals) by admin on 28-01-2012

download
The PCV system is designed to prevent blow-by gas from escaping to the atmosphere by drawing it directly into the intake manifold. The PCV valve contains a spring-loaded plunger which is lifted in proportion to intake manifold vacuum. Under high vacuum, blow-by is returned directly to the manifold through the breather chamber and PCV valve with fresh air. When intake manifold vacuum decreases (wide open throttle) and vacuum in the air cleaner increases, the PCV valve closes and the blow-by is returned through the cylinder head cover breather hose and into the air cleaner. The PCV valve also acts as a check valve when the engine backfires to prevent crankcase explosion. Fig. 1: PCV system components-1984-87 1.5L engines Fig. 2: PCV system components-1988-91 1.6L engines Fig. 3: PCV system components-1992-95 engines Fig. 4: PCV system components-1984-87 carbureted engines
SERVICE Positive Crankcase Ventilation (PCV) Valve For PCV valve removal, refer to Routine Maintenance of this information. 1. Locate the PCV valve. With the engine running at idle, use pliers to pinch the PCV hose between the valve and the intake manifold. It should be possible to hear the spring loaded valve click shut. 2. If no click is heard, remove the valve from the engine but leave it connected to the intake manifold. A hissing sound should be heard and vacuum should be felt at the valve inlet. 3. If no vacuum is felt, remove the valve from the intake manifold hose. The engine should stall or almost stall. This will indicate a stuck valve or clogged hose. Check the breather hose for clogging or leaks and replace any defective parts. Exhaust Gas Recirculation (EGR) System FUEL INJECTED ENGINES General Information See Figure 3 The Exhaust Gas Recirculation (EGR) system is used to control emissions measured at the tailpipe. Components included are the EGR valve and controls. The EGR system uses a poppet type valve to regulate the amount of exhaust gas flowing into the intake manifold. The flow path is cast into the cylinder head and does not use any external tubing. A control solenoid valve regulates the amount of vacuum to the EGR valve. A Constant Volume Control (CVC) valve provides a constant amount of vacuum to the control solenoid valve over a wide range of engine vacuum.

2000-2004 Toyota Celica GT Air Intake Removal And Installation Guide

0

Filed Under (Toyota Manuals) by admin on 05-11-2011

download
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the mass air sensor electrical connection. 3. Depress the center pins on the push clips on the radiator core support cover. 4. Remove the radiator core support cover. 5. Unclip the relay and fuse box and move out the way. 6. Loosen and remove the bolt on the radiator core support. 7. Unclip the PWM vacuum switching valve from the air cleaner assembly. 8. Pull to remove the computer fresh air tube. 9. Loosen the clamps on the stock intake tube, then remove the stock intake tube. 10. Remove the two stock rubber hoses from the air cleaner lid. 11. Remove the EVAP OBD canister closed valve vent hose from the hard line. 12. Push back, and pull up to gain access to the bottom of the air cleaner assembly. 13. Remove the vacuum hose from the intake manifold. 14. Disconnect the vacuum switching valve electrical connection. 15. Using a pair of pliers unclip the wire harness from the back of the air cleaner assembly. 16. Disconnect the EVAP OBD canister closed valve electrical connection. 17. Remove the complete air cleaner assembly. 18. Disconnect the PWM vacuum switching valve electrical connection. 19. Remove the stock bracket from the PWM vacuum switching valve. 20. Remove the mass air sensor from the air cleaner assembly. 21. Loosen and remove the EVAP OBD canister closed valve from the air cleaner assembly. 22. Disconnect the vacuum hoses from the vacuum switching valve, then remove the vacuum switching valve from the bottom of the air cleaner assembly. 23. Remove the two vent hoses from the EVAP OBD canister closed valve. 24. Install the mass air sensor into the intake tube and secure. 25. Loosen and remove the stock nut on the relay and fuse box support bracket. 26. Install the EVAP OBD canister closed valve assembly into the vehicle and connect the hose to the hard line, then secure the bracket to the relay and fuse box support bracket using the nut removed before

Related Content:

1993 Corvette Service Manual PDF, vent line 1998 mercy sable, VACUUM LINES ON A 2003 GM 6 CLINDER, vacume lines on 2004 pt cruiser gt, What color is the tcc solenoid in toyota sequoia, 2002 2 4L olds alero vacuum hose routing diagram, ford taurus 2001 engine vacuum hoses on intake, pt cruiser vacuum system diagram, vaccum lines 2001 pt cruiser, Does a volvo d12 engine require silicone or gasket between engine and flywheel housing