electrical draw battery chevy 5amps 8

You search PDF repair manual about electrical draw battery chevy 5amps 8, if there are search results will appear below. If search results do not exist, please search by others keyword.



  electrical draw battery chevy 5amps 8 Direct Download speed 5432 Kb/s

  electrical draw battery chevy 5amps 8 Full Version speed 8172 Kb/s



Battery Electrical Drain/ Parasitic Load Test Repair Manual

0

Filed Under (More Manuals) by admin on 29-05-2012

download
1. Disconnect the battery negative cable 2. Install the male end of the J 38758 to the negative battery terminal. 3. Turn OFF the test switch. 4. Install the negative battery cable to the female end of the test switch. 5. Install the Scan Tool (or equivalent) or wait for 20 minutes. 6. Turn ON the test switch. 7. Road test the vehicle while activating all accessories, including the radio and the air conditioning. 8. Lower the door glass, then exit the vehicle. Do not move the door handle after closing the door. 9. Open the hood. Important The power down timer will reset to 20 minutes if any wake up inputs are received by a Class 2 device (after the scan tool has put all Class 2 devices to sleep). 10. Put all of the Class 2 devices into the sleep mode. 11. Turn OFF the ignition switch. Remove the key. Important From this point on, electrical continuity must be maintained in the ground circuit of the battery through the Test Switch J 38758 in the ON position or through the ammeter J 39200 . 12. Components such as PCM, VCM, Automatic Air Conditioning, and the Truck Body Control Module have timers that draw several amps of current while they cycle down. This can give a false parasitic drain reading. Wait 20 minutes for these components to power down before continuing this test (or use the scan tool to put all Class 2 devices to sleep). 13. Connect a jumper wire with a 10 A fuse J 36169-A to the terminals of the test switch. 14. Turn the test switch to the OFF position. 15. Wait ten seconds. If the fuse does not blow, the current is less than 10 A. The ammeter can be used safely. 16. Before the fused jumper wire is removed, turn the test switch to the ON position. Important If an ammeter other than the J 39200 is used, ensure that the vehicle does not have a high current drain that would damage the ammeter when connected to the circuit. 17. Perform the following procedure in order to detect a high current drain: A. Set the ammeter J 39200 to the 10 A scale. B. Connect the ammeter to the test switch terminals. C. Turn OFF the test switch. This allows the current to flow through the ammeter. D. Wait one minute, then inspect the current reading. Ñ When there is a current reading of 2 A or less, turn ON the test switch, this maintains continuity in the electrical system. Ñ Then, switch the meter down to the 2 A scale, for a more accurate reading, when the test switch is reopened. E. Open the test switch. F. Take the reading in milliamps. G. Note the battery reserve capacity. Refer to Battery Usage . Ñ Divide this number by 4. Example: 90/4 = 22.5 Ñ Compare this to the ammeter reading. Ñ The current drain in milliamps should not exceed this number. Ñ Example: if a battery has a reserve capacity of 90 minutes, the current drain should not exceed 22 milliamps. H. When the current draw is too high, remove the electrical system fuses one at a time until the draw returns to a value less than or equal to specifications. Ñ Start with the fuses that are hot all the time. Ñ To remove the fuse, you must first open the door, which causes a high enough current flow to damage the ammeter. Ñ Protect the ammeter, without disturbing the electrical continuity, by turning ON the test tool before opening the door. Ñ Remove the courtesy lamp fuse. Ñ Note the ammeter reading. Ñ If the parasitic load is still excessive, start removing the remaining fuses one at a time. Ñ Keep the courtesy lamp fuse out during diagnosis, so the door can remain open. Ñ Perform Steps 11 through 13 each time a fuse is removed. I. Removing the PCM or VCM fuse should cause a drop of less than 10 milliamps. A drop greater than 10 milliamps indicates a possible short to ground. J. Check the orange wires along with the components connected to the orange wires. No drop in the milliampere reading indicates the PCM or VCM is not drawing current. K. Repeat the parasitic current drain test procedure after any repair has been completed. L. When the cause of the excessive current draw has been located and repaired, remove the ammeter and the parasitic draw test switch.

Related Content:

c7 cat cgi system, paricite draw on ford electrical system, 03 chevy pu relay causing parasitic draw, does the ignition off draw switch ram drain battery, e4od solenoid pack testing, how to do a paracitic load test on a 2005 acura mdx, how to test 1258168600 nippon denso ignition module, how to test solenoids 4f27e, how to use the parasitic drain test switch, overdrive sistem repair manual dodge

1997 Dodge Grand Caravan POWERTRAIN CONTROL MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 06-02-2012

download
POWERTRAIN CONTROL MODULE (PCM) Removal & Installation 1. The PCM is located between driver’s side front fender and power distribution center, near battery. See Fig. 1 . Disconnect negative battery cable and then positive battery cable from battery. 2. Remove bolts on side of power distribution center that secure power distribution center to mounting bracket. Remove heat shield from outside of battery. Remove battery. 3. Rotate power distribution center toward the engine to disengage power distribution center from rear mounting bracket. Pull power distribution center toward rear of vehicle to disengage power distribution center from front mounting bracket. 4. Allow power distribution center to lay aside for access to PCM. Remove electrical connectors from PCM. Electrical connectors may be removed by squeezing tabs on electrical connector together and pulling electrical connector from PCM. Remove bolts and PCM. To install, reverse removal procedure. Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. Default data is used until new data from each key start is stored. As the computer restores its memory from each new key start, driveability is restored. Driveability problems may occur during the relearn stage. Depending on the vehicle and how it is equipped, the following driveability problems may exist: z Rough or unstable idle. z Hesitation or stumble. z Rich or lean running. z Poor fuel mileage. z Harsh or poor transmission shift quality. To accelerate relearn process after battery removal and installation, vehicle should be road tested in the following manner: z Vehicle at normal operating temperature (cooling fan cycles). z Accelerate at normal throttle position (20-50%). z Cruise at light to medium throttle. z Decelerate to a stop, downshifting and using brakes normally. Manufacturers identify specific relearn procedures. See RELEARN PROCEDURES. Always complete the procedure before returning the vehicle to the owner. RELEARN PROCEDURES Theft Alarm Relearn Procedure 1. Theft alarm relearn is necessary whenever battery is disconnected or dead battery is boosted. If battery is connected or boosted without conducting relearn procedure, alarm system will enter power-up mode and vehicle will not start. 2. Before reconnecting battery or connecting booster, insert door key into driver side door lock

Related Content:

IDLE RELEARN 02 CAMRY, 04 rav4 idle at 6000 rpm after battry change, 2001 malibu throttle position sensor relearn procedure, 2006 cheverolet impala will not idle, 2008 dodge grand caravan coolant fan runs continuasly, dodge caravan1997 transm autom 3 3l how connected with radiator, Dodge Cruise Control Repair 2012 caravan, IRRATIC IDLING 87 2 8 V6 BLAZER

1999 Chrysler LHS V6-3.5L VIN G Battery Replacement Manual

0

Filed Under (Chrysler Manuals) by admin on 24-06-2012

download
Battery Replacement Notes WARNING: TO PROTECT THE HANDS FROM BATTERY ACID, A SUITABLE PAIR OF HEAVY DUTY RUBBER GLOVES, NOT THE HOUSEHOLD TYPE, SHOULD BE WORN WHEN REMOVING OR SERVICING A BATTERY. SAFETY GLASSES ALSO SHOULD BE WORN . REMOVAL 1. Turn the steering wheel all the way to the right. 2. Verify that the ignition switch and all accessories are OFF. 3. Disconnect and isolate the negative battery cable remote terminal from the remote battery post. 4. Remove air cleaner housing. 5. Remove battery splash shield. 6. Remove two short bolts to battery hold down. 7. Slide battery rearward to disconnect the negative and positive battery terminals from battery. 8. Slide battery toward rear of vehicle and lift out through wheel well opening. 9. Remove battery from vehicle. 1. Tighten clamp nuts to 8.5 N.m (75 in. lbs.) torque.INSTALLATION For installation, reverse the above procedures. Inspect and clean battery and attaching components before installation. WARNING: DO NOT OVER TIGHTEN BATTERY CABLE CLAMPS, DAMAGE TO CLAMPS CAN RESULT .

Related Content:

where is the battery located on a dodge journey 2010, snap-on YA201 battery tester owners manual pdf, what size battery for a 1997 buick regal, snap on ya 201 switch, NOCO Battery Isolator Instructions, how to replace battery on 2014 dodge journey, how to remove battery chevy cruze, how to charge battery in 2012 chevy equinox, battery location 2013 dodge journey, 2012 honda crv heavy duty battery

Ford Sierra Service and Repair Manual Download

0

Filed Under (Ford Manuals) by admin on 20-05-2012

download
Puddles on the garage floor or drive, or obvious wetness under the bonnet or underneath the car, suggest a leak that needs investigating. It can sometimes be difficult to decide where the leak is coming from, especially if the engine bay is very dirty already. Leaking oil or fluid can also be blown rearwards by the passage of air under the car, giving a false impression of where the problem lies. Warning: Most automotive oils and fluids are poisonous. Wash them off skin, and change out of contaminated clothing, without delay. Identifying leaks The smell of a fluid leaking from the car may provide a clue to what’s leaking. Some fluids are distinctively coloured. It may help to clean the car carefully and to park it over some clean paper overnight as an aid to locating the source of the leak. Remember that some leaks may only occur while the engine is running. Sump oil Gearbox oil Brake fluid Power steering fluid Oil from filter Antifreeze Engine oil may leak from the drain plug… …or from the base of the oil filter. Leaking antifreeze often leaves a crystalline deposit like this. Gearbox oil can leak from the seals at the inboard ends of the driveshafts. A leak occurring at a wheel is almost certainly brake fluid. Power steering fluid may leak from the pipe connectors on the steering rack. 0•9 Roadside repairs When jump-starting a car using a booster battery, observe the following precautions: ? Before connecting the booster battery, make sure that the ignition is switched off. ? Ensure that all electrical equipment (lights, heater, wipers, etc) is switched off. ? Make sure that the booster battery is the same voltage as the discharged one in the vehicle. ? If the battery is being jump-started from the battery in another vehicle, the two vehcles MUST NOT TOUCH each other. ? Make sure that the transmission is in neutral (or PARK, in the case of automatic transmission). Jump starting will get you out of trouble, but you must correct whatever made the battery go flat in the first place. There are three possibilities: 1 The battery has been drained by repeated attempts to start, or by leaving the lights on. 2 The charging system is not working properly (alternator drivebelt slack or broken, alternator wiring fault or alternator itself faulty). 3 The battery itself is at fault (electrolyte low, or battery worn out). Connect one end of the red jump lead to the positive (+) terminal of the flat battery Connect the other end of the red lead to the positive (+) terminal of the booster battery. Connect one end of the black jump lead to the negative (-) terminal of the booster battery Connect the other end of the black jump lead to a bolt or bracket on the engine block, well away from the battery, on the vehicle to be started. 1 2 3 4 Make sure that the jump leads will not come into contact with the fan, drive- belts or other moving parts of the engine. 5 Start the engine using the booster battery, then with the engine running at idle speed, disconnect the jump leads in the reverse order of connection

Related Content:

2005 ford escape battery drain, ac leaking in chevy trailblazer, antifreeze for a 2013 chevy cruze, chevy cruze coolant leak

2000-2004 Honda Insight IMA System Indicator On With IMA DTC 77 REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 16-01-2012

download
PROBLEM The IMA system indicator comes on and IMA DTC 77 (P1447) (battery module deterioration) or DTC 78 (P1449) (battery module deterioration) is set. CORRECTIVE ACTION Replace the battery module. If needed, replace the motor control module (MCM), the battery condition monitor (BCM), or both INSPECTION PROCEDURE 1. Turn the ignition switch to LOCK (0). 2. Remove the cargo floor mat (see page 20-44 of the 2000-04 Insight Service Manual). (In ISIS, use the keyword FLOOR MAT , and select Interior Trim Removal/Installation – Cargo Area from the list.) 3. Remove the battery module switch cover (two bolts), then remove the locking cover from the switch. 4. Flip the battery module switch to OFF . Reinstall the locking cover. 5. Wait at least 5 minutes to let the capacitors in the system discharge. 6. Remove the right trunk shelf support (five clips and two bolts). 7. Remove the six mid-frame cover bolts. Remove the intelligent power unit (IPU) lid (17 bolts). 8. Measure the voltage at the junction board terminals. There should be 30 V or less . If you read more than 30 V , there is a problem in the circuit; do the DTC troubleshooting first. SWITCH COVER LOCKING COVER BOLTS LOCKING COVER BATTERY MODULE SWITCH IPU LID RIGHT TRUNK SHELF SUPPORT BOLTS (17) CLIPS CLIPS BOLTS ON JUNCTION BOARD TERMINALS REPAIR PROCEDURE 1. Remove the battery module from the vehicle (see page 12-113 of the service manual). (In ISIS, use the keyword BAT MOD , and select Battery Module Removal/Installation from the list.) 2. Remove the lifting tool from the battery module. 3. Remove the mounting bolts for the MCM and the BCM (eight total). Unplug the electrical connectors (five for the MCM and three for the BCM), then remove the modules. 4. Install the MCM and the BCM in the new battery module. Use the original MCM and BCM if no replacement was needed; otherwise, use the appropriate replacement parts. Torque the mounting bolts to 9.8 N·m (7.2 lb-ft) . 5. Install the lifting tool on the battery module. 6. With someone to help you, carefully lift the battery module into the vehicle, and set it down into position. Remove the lifting tool. 7. Plug in the connectors, and install the Y condenser harness. Then install the mounting bolts. Torque the bolts to 24 N·m (17 lb-ft) . 8. Install the battery module air duct. Torque the bolt to 9.8 N·m (7.2 lb-ft) . 9. Connect the high voltage cables to the junction board. Torque the bolts to 9.8 N·m (7.2 lb-ft) . 10. Install the front and rear IPU braces and the mid- frame. Torque the bolts to 9.8 N·m (7.2 lb-ft) . Model Year MCM Part Number Replacement Part Number M/T Models 2000-01 1K000-PHM-000 thru 1K000-PHM-050 1K000-PHM-060 (H/C 7071525)

Related Content:

020139007 service bulletin, battery restoration procedure, servicing a battery module honda insight

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

0

Filed Under (Pontiac Manuals) by admin on 07-06-2012

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

Related Content:

Bully Side Step Installation, wiring diagram for mitsubishi canter ignition, what is the tcc solenoid on a 2 2 cavalier, Powertrain Generator 6500 Parts Diagram, Kia Rio 2001 DTC P0753, bully side ste for jeep instructions, 2006 pontiac g6 gt code po753, 4t80e tcc solenoid replacement, powertrain generator 6500 owners manual, 2002 cavalier shift mdule location

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to remove 2011 dodge durango grill, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

2000 Ford Crown Victoria/ Grand Marquis Intake Manifold – Gasoline Engines Removal and Installation Manual

0

Filed Under (Ford Manuals) by admin on 16-04-2012

download
Intake Manifold—Gasoline Engines Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 4. Disconnect the fuel line. For additional information, refer to Section 310-00A or Section 310-00B . 5. Remove the wiper arm and pivot shaft. For additional information, refer to Section 501-16 . 6. Remove the drive belt. For additional information, refer to Section 303-05 . 7. Raise the vehicle on a hoist. For additional information, refer to Section 100-02 . 8. Disconnect the electrical connector at the crankshaft position (CKP) sensor. * Disconnect the pin-type retainer from the A/C compressor bracket. 9. Disconnect the electrical connector from the A/C compressor. 10. Remove the oil bypass filter. 11. Disconnect the oil pressure sensor electrical connector and the power steering pressure (PSP) switch electrical connector. 12. Disconnect the exhaust gas recirculation (EGR) tube from the exhaust manifold 13. Lower the vehicle. 14. Disconnect the two differential pressure feedback EGR hoses. 15. Disconnect the RH heated oxygen sensor electrical connector. 16. Disconnect the fuel charging wiring electrical connectors from the eight ignition coils. 17. Disconnect the fuel charging wiring electrical connectors from the eight fuel injectors. 18. Disconnect the accelerator cable and the speed control actuator cable. 19. Remove the cables from the EGR tube heat shield and position out of the way. 20. Remove the bolts and the EGR tube heat shield. 21. Disconnect the evaporative emissions (EVAP) return tube, the main chassis vacuum supply line, and the EGR valve vacuum supply. 22. Disconnect the positive crankcase ventilation (PCV) tube assembly at two locations and remove. 23. Disconnect the electrical connector from the EGR vacuum regulator solenoid. 24. Disconnect the vacuum line from the EVAP canister purge valve. 25. Disconnect the generator cable and electrical connector 26. Remove the bolts and the generator mounting bracket. 27. Remove the upper radiator hose. 28. Disconnect the electrical connector from the idle air control (IAC) valve and the throttle position (TP) sensor. 29. Disconnect the heater water hose. 30. Disconnect the EGR tube from the EGR valve. 31. NOTE: The LH heated oxygen sensor and the transmission electrical connectors are attached to the wiring bracket and must be separated from the bracket. Remove the wiring bracket. * Disconnect the wiring connectors. * Separate the transmission harness from the stud. * Remove the nut and the bolt and remove the bracket.

Related Content:

2005 GMC Sierra 1500 How to Disconnect Vacuum Line, can you unplug the trorque converter on a 1999 honde ex, disconnected battery car turn over will not start 99 bmw 528i, dodge grand caravan liftgate slams shut, part ground strap crown vic 2011 3w7t, where is the vent pipe located on 2004 sierra gas fill up hose

1999 Ford Windstar Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals, Uncategorized) by admin on 23-04-2012

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04 . 2. Remove the passenger side air bag module. Refer to Section 501-20B . 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. * Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector 18. Disconnect the automatic transmission shift cable. 1. Disconnect the cable from the steering column shift tube lever. 2. Disconnect the cable from the steering column bracket. 19. Separate the intermediate shaft from the steering column. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column. 20. Disconnect the climate control harness electrical connector. 21. Disconnect the climate control vacuum harness connector. 22. Disconnect the fuse junction panel electrical connectors. 23. Remove the LH instrument panel reinforcement bol 4. Remove the four instrument panel center support bolts. 25. Remove the instrument panel defroster opening grille. * If equipped, disconnect the sunload sensor electrical connector. 26. Remove the cowl top bolts. 27. Remove the RH cowl side bolts. 28. Remove the LH cowl side bolts. 29. NOTE: Two technicians are required to carry out this step. Remove the instrument panel. Installation CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. NOTE: Two technicians are required to carry out this step

Related Content:

2000 Isuzu 5 7 NPR Repair Manual lower intake manifold, charging system on 1999 isuzu npr not charging gas engine, ford five hundred instrument panel, remove ac panel from ford five hundred

Toyota Landcruiser / Scout Weatherproof Harness Wire Harness Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-03-2012

download
Grounding the Automobile A perfectly and beautifully wired automobile will nevertheless have bugs and problems if everything is not properly grounded. Do not go to the careful effort of installing a quality wire harness only to neglect proper grounding. Note: The Painless Wire Harness Kit includes no ground wire except the black wire from the two headlamp connectors. You must supply ground wire (14-16 gauge) for all circuits. 6.3.1 Connect a Ground Strap or Cable (2-gauge minimum) from the Negative Battery terminal to the automobile chassis (frame). 6.3.2 Connect a Ground Strap from the Engine to the chassis (even a 10-gauge wire is too small) . DO NOT RELY UPON THE MOTOR MOUNTS TO MAKE THIS CONNECTION . 6.3.3 Connect a Ground Strap from the Engine to the Body. 6.3.4 If you have a fiberglass body you should install a terminal block to ground all your Gauges and Accessories. Ground the Terminal Block with at least a 12-gauge wire to the chassis. 6.4 Terminal Installation and Making Connections Note: In the following steps you will be making the circuit connections. Before you start, you should carefully read Sections 7.0 through 10.0 , as appropriate, and continually refer to Section 10.0 , DOUBLE- CHECKING your routing and length calculations before cutting any wires and making connections. Give special attention to Turn Signal and Ignition Switch connections. These can be somewhat confusing. 6.4.1 Have all needed tools and connectors handy. 6.4.2 Select the correct size terminal for the wire and stud application. 6.4.3 Determine the correct wire length and cut the wire. Remember to allow enough slack in the harness and wires at places where movement could possibly occur, such as automobile body to frame, frame to engine, etc. Double-check your calculations. 6.4.4 Strip insulation away from wire. Strip only enough necessary for the type of terminal lug you are using. Note: In the following step, make sure that the terminal is crimped with the proper die in the crimping tool. An improper crimp will NOT make a good connection. 6.4.5 Crimp the terminal onto the wire. CAUTION: DO NOT OVER-CRIMP! 6.4.6 Connecting the harness throughout the groups is a redundant process. Make sure that each wire is FIRST properly routed and THEN attach. DO NOT ATTACH FIRST THEN ROUTE AFTERWARD. 6.4.7 When all wires are attached, tighten the mounts and ties to secure harness permanently. 6.5 Testing The System 6.5.1 Use a small (10 amp or less) battery charger to power up the vehicle for circuit testing. If there is a problem anywhere, the battery charger’s low amperage and internal circuit breaker will provide circuit protection. CAUTION: IF YOU HAVE NOT YET DISCONNECTED THE BATTERY FROM THE AUTOMOBILE, DO SO NOW! DO NOT CONNECT THE BATTERY CHARGER WITH THE BATTERY CONNECTED. Connect the battery charger’s NEGATIVE output to the automobile chassis or engine block and its POSITIVE output to the automobile’s positive battery terminal. 6.5.2 INDIVIDUALLY turn on each light, ignition, wiper circuit, etc. and check for proper operation. Note: The turn signals will not flash properly if you do not have both the front and rear bulbs installed and connected. 6.5.3 When all circuits check out THEN attach the battery cable to the battery for vehicle operation

Related Content:

where are the battery terrminals on a 2012 pruis, 1996 ford f53 chassis circuit board diagram, 1996 ford F53 wiring diagrams, 97 cadillac deville ground location, FORD E-450 FUEL PUMP WIRING

Related Content:

c7 cat cgi system, paricite draw on ford electrical system, 03 chevy pu relay causing parasitic draw, does the ignition off draw switch ram drain battery, e4od solenoid pack testing, how to do a paracitic load test on a 2005 acura mdx, how to test 1258168600 nippon denso ignition module, how to test solenoids 4f27e, how to use the parasitic drain test switch, overdrive sistem repair manual dodge