Skip to content

84 bronco 2 4x4 front wheel bearing replacement

You search PDF repair manual about 84 bronco 2 4x4 front wheel bearing replacement, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

1997 Ford Aerostar/ Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

download
Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03 . 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03 . 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation

2000 BMW 528i (E39) DOHC Front Wheel Bearing Removal And Installation Manual

download
Replacing Front Wheel Bearing ( Wheel Hub )(Basis) Caution! Bearing cannot be dismantled. Do not wash out bearings. Remove brake disk (brake line remains connected), refer to Brakes and Traction Control; Disc Brake System. Remove ABS impulse sensor. Remove stabilizer link from stabilizer, Steering and Suspension. Unfasten nut. Installation: Use washer (1). Tapered spigot and bore both free of grease. Replace self-locking nut. Brace on hexagon socket if necessary. Tightening Torque, refer to Steering Specifications. Press off track rod with special tool 31 2 240. Mark the installation position of the spring strut tube (1) in the swivel bearing (2) with paint – never mark with scribing tool. Marking is not required if the factory mark is still identifiable. R installation position of right spring strut tube L installation position of left spring strut tube Version with factory marking above the swivel bearing. Unfasten nut. Expand swivel bearing with special tool 31 2 200 and pull swivel bearing downwards. Installation: Press swivel bearing upwards to stop with workshop hoist and note marking of installation position. Replace self-locking nut. Tightening Torque, refer to Suspension Specifications Unfasten screws and remove wheel bearing. Installation: Contact face (2) of wheel bearing and swivel bearing and the threaded bores (1) must be clean and free of grease. Tightening Torque, refer to Suspension Specifications

1994 Ford Pickup F150 WHEEL BEARING ADJUSTMENT

download
Bronco & F150 (Automatic Locking Hub) 1. Raise and support front of vehicle. Remove wheels. Remove locking hub assembly. See AUTOMATIC LOCKING HUBS under REMOVAL & INSTALLATION. Remove outer lock nut with Spanner Lock Nut Wrench (D85T-1197-A). See Fig. 3 . 2. Remove lock washer. Tighten inner lock nut to 50 ft. lbs. (68 N.m). Back off inner lock nut and retighten to 30-40 ft. lbs. (41-54 N.m). While rotating hub, back off lock nut 90 degrees. Install lock washer so key is positioned in spindle groove. 3. Rotate inner lock nut so pin is aligned in nearest lock washer hole. Install and tighten outer lock nut to 160-205 ft. lbs. (217-278 N.m). Final end play of hub should be .00-.004″ (.00-.11 mm). Torque required to rotate hub and rotor should not exceed 20 INCH lbs. (2.3 N.m). Install hub locks and wheels. 1994 Ford Pickup F150 WHEEL BEARING ADJUSTMENT

2009 Cadillac CTS AWD Front Wheel Drive Shaft Replacement – Left Side

download
Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle ( See: Maintenance\Vehicle Lifting\Service and Repair ). 2. Remove the left front tire and wheel. Refer to Tire and Wheel Removal and Installation ( See: Maintenance\Wheels and Tires\Service and Repair ). 3. Remove the left outer tie rod from the steering knuckle. Refer to Steering Linkage Outer Tie Rod Replacement (All Wheel Drive) ( See: Steering and Suspension\Steering\Tie Rod\Service and Repair\Steering Linkage Outer Tie Rod Replacement )Steering Linkage Outer Tie Rod Replacement (Rear Wheel Drive) ( See: Steering and Suspension\Steering\Tie Rod\Service and Repair\Steering Linkage Outer Tie Rod Replacement ). 1. Install the new O-ring (2) on the intermediate shaft. 2. Install the new retaining ring (1) on the intermediate shaft. 3. Apply a small amount of grease GM P/N 01051344 (Canadian P/N 993037) or equivalent to the intermediate wheel drive shaft splines. 4. Install the left front wheel drive shaft in the intermediate shaft. 5. To ensure that the wheel drive shaft is installed properly, grasp the inner tripod housing and pulling it outward. DO NOT pull on the axle shaft . 6. Install the wheel drive shaft in the front knuckle. 7. Install the left upper control arm on the knuckle. Refer to Upper Control Arm Replacement ( See: Steering and Suspension\Suspension\Control Arm\Service and Repair\Rear Suspension\Upper Control Arm Replacement