92 buick riviera repair manual download

You search PDF repair manual about 92 buick riviera repair manual download, if there are search results will appear below. If search results do not exist, please search by others keyword.



  92 buick riviera repair manual download Direct Download speed 5432 Kb/s

  92 buick riviera repair manual download Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to replace 2003 impala power steering pump, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, youtube replace the hub on a meritor ff981 axle, how to change power steering pump 2009 acada

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 2006 ford focus ses repair manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, cft30 scan codes, 1999 chevy S10 - manual, repair sunroof 2007 trailblazer, 96 Cavalier & Sunfire shop service repair manual, 1999 cavalier A/C instructions

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, Replacing the reverse band Dodge 1500, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, repair manual for 1998 chevrolet 1500, downloadable schematic for 99 Chevy suburban evap system, ax12-1500 nut torque, 2010 silverado 1500 4 3 liter canister vavle solenoid, how to replace actuator on 2005 chevy 1500, lifter repair on 02 avalanche

Acura MDX Torque Converter Shudder or Vibration Between 35 and 40 MPH Repair Manual

0

Filed Under (Acura Manuals) by admin on 24-11-2011

download
1. To confirm the client’s complaint, test-drive the vehicle on a smooth road, preferably with a slight incline. Set the cruise control between 35 and 40 mph, and monitor the engine rpm using the vehicle’s tachometer, or use the HDS to take a snapshot of the engine rpm. 2. If the engine speed fluctuates several hundred rpm while maintaining a constant vehicle speed, disconnect the EGR valve and retest the vehicle. •If the fluctuation is gone, refer to the EGR troubleshooting in the service manual. •If the engine rpm still fluctuates, and the transmission does not have any other symptoms (shifting problems, slipping, transmission DTCs) go to step 3. 3. Drain the transmission fluid, then strain it through a paint strainer. •If you find little or no contamination in the strainer, the ATF is OK, even if it smells burnt, is discolored, and/or the magnetic drain plug has small chips, flakes, or metal fuzz on it. Go to REPAIR PROCEDURE A . •If you find large amounts of contamination (pieces of metal or friction material) in the strainer, go to REPAIR PROCEDURE B . REPAIR PROCEDURE A 1. Remove the torque converter: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Install the torque converter: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 3. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 4. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. •Start the engine, and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes. REPAIR PROCEDURE B Follow the IN-WARRANTY EXCHANGE steps in service bulletin 90-009, Automatic Transmission In- Warranty Exchange Program , to order a remanufactured A/T, replace the failed A/T, and return the failed A/T core. 1. Remove the transmission: •Refer to page 14-203 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T REM , and select A/T Removal from the list. 2. Clean the transmission cooler. Refer to service bulletin 89-015, ATF Cooler Cleaner . 3. Install a remanufactured transmission: •Refer to page 14-215 of the 2003-04 MDX Service Manual , or •Online, enter keyword A/T INSTALL , and select A/T Installation from the list. 4. Update the PGM-FI software using HDS version 1.018.016 or later (see SOFTWARE INFORMATION ). Refer to service bulletin 01-026, Updating the ECM/PCM . 5. Do the idle learn procedure: •Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off. •Start the engine and let it run until it reaches its normal operating temperature (cooling fan cycles twice). •Let the engine idle with the throttle fully closed for 10 minutes

Related Content:

1998 mazda MPV owners manual, 2002 ford thunderbird service manual, freelander engine control module mobility module master, how much for torque converter for 2001 mdx, torque converter problems symptoms for 1999 3 2tl acura, what is a torque shudder

ALL INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 23-04-2012

download
SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. Groan noise during stopping: • Usually caused by glazing of the rotor’s surface as a result of heavy or frequent braking. • Refer to technical bulletins specific to the model of vehicle regarding this issue. • Replace the brake pads, then resurface the rotors and finish them with sand paper. Refer to Brake Service on page 5 for additional detail. Single clunk noise from front suspension when applying the brakes: • The noise is a result of the brake pads shifting in the direction of rotor rotation when the brakes are applied. Can be duplicated by lightly touching the brake pedal. • • If the brake pedal is pushed hard, the noise is less likely to occur. Make sure the brake pads and pad hardware (shims, springs, clips, etc) are installed correctly. Refer to ASIST for vehicle specific brake service information. Refer to Brake Service on page 5 for additional detail. Mull e he engine is started: • st er models, the self check occurs the first aches 5 mph after the engine is started. ors or drums. • WARNING: Brake dust may be hazardous if inhaled. Refer to the Service Manual (ESM) for brake • n and lubrication of brake pads, CAUTION: Do not get grease on the brake pad friction surface. A • Brake Judder is caused by rotor thickness variation and/or rotor run out.

Related Content:

psc under hybrid highlander, titan 5500 generator manual, Free 98 Honda Accord service Repair Manual, lexus engine 2gr-fe chirping squeak noise sb0010-09, manual for 1993 bmw 325i, Electrical Troubleshooting Manual r129 pdf, 2012 f-150 service manual, honda ridgeline b136, 2011 camaro owners manual pdf, 2010 jeep wrangler service manual

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Related Content:

4t65e documentation pdf, 4t65e pdf

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

0

Filed Under (Ford Manuals) by admin on 15-05-2012

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

Related Content:

kancil 850 manual transmission pdf, Haynes Saxophone Manual pdf, manual hino j08, m1078a1p2 a/c, manual lever position sensor troubleshooting, manual webasto pdf, repair manuel 91 suburu loyle, sportivo owners handbook manual pdf, webasto top slider 2 instrukcja, 0761 emission code ford

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-07-2012

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

Related Content:

Sienna Sliding Door Cable Replacement, 1998 sienna repair manual, how to fix g-6 door latch, how to remove a chevy tahoe bump stop, lexus door adjustment wind, toyota sienna sliding door repair manual

Honda Idle Fluctuation and/or the MIL Is On With DTC P1129 and/ or P0505 Repair Manual

0

Filed Under (Honda Manuals) by admin on 07-05-2012

download
DIAGNOSIS 1. Start the engine, and let it idle until it warms up. Does the idle fluctuate, or is there a customer complaint of an intermittent idle fluctuation? Yes – Odyssey : Go to REPAIR PROCEDURE A. Pilot : Go to REPAIR PROCEDURE B. No – Go to step 2. 2. Connect the HDS to the vehicle’s DLC, and check for DTCs. Is DTC P1129 or P0505 stored? Yes – Go to REPAIR PROCEDURE B. No – Continue with normal troubleshooting. REPAIR PROCEDURE A 1. Connect the HDS to the vehicle’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading 4. From the System Selection Menu screen, select PGM-FI . 5. From the Mode Menu, select DATA LIST . 6. Scroll down the list to PSP SWITCH . Watch the reading in the Value column. 7. Check for a broken power steering pressure switch wire by wiggling the P/S pressure switch wire harness at the switch while you check the Value column reading. •If the reading changes between on and off when you wiggle the harness, go to step 8. •If the reading does not change between on and off when you wiggle the harness, go to REPAIR PROCEDURE B. 8. Raise the vehicle on a lift, and remove the right front wheel to access the power steering pressure switch. 9. Disconnect the connector from the switch, and release the harness clip from the body. NOTE: You may need to disconnect the Secondary HO2S connector to free the end of the harness from the body. 10. Lower the vehicle, and pull the harness up for easier access to make the repair. 11. Remove the rubber seal from the connector, and remove the terminals from the connector noting the GRN wire and BLK wire locations. 12. Remove the tape from the corrugated tube and the wires up to the harness clip; mark the wires at the end of the corrugated tube

1999 GMC Truck Yukon PRNDL Display Inaccurate or Inoperative PRNDL Inaccurate Repair Manual

0

Filed Under (GMC Manuals) by admin on 15-02-2012

download
Did you perform the Instrument Cluster System Check? — Go to Step 2 Go to Instrument Cluster System Check 2 1. Disconnect the Transmission Range (TR) Switch connector C2. 2. Turn the ignition switch to the RUN position. 3. Conduct the PRNDL Logic Input Test by connecting fused jumper wires between ground and the appointed cavities of the TR Switch connector. Refer to PRNDL Logic Input Test PRNDL Logic Input Test . 4. Repeat for each transmission range. Do all ranges illuminate? — Go to Step 3 Go to Step 4 3 Adjust the transmission range switch. Refer to Park/Neutral Position Switch Adjustment (4L60E); Park/Neutral Position Switch Adjustment (4L80E) Automatic Transmissions. Replace the PNP Switch. Refer to Park/Neutral Position Switch Replacement (4L60E); Park/Neutral Position Switch Replacement (4L80E) in Automatic Transmissions. Is the repair complete? — Go to Instrument Cluster System Check — 4 1. Remove the I/P Cluster. 2. Connect a J 39200 DMM (continuity) between the I/P Cluster connector and connector C2 of the TR Switch to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 6 Go to Step 5 5 Locate and repair the open in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 6 Connect a J 39200 DMM (continuity) between the I/P Cluster connector and ground to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 7 Go to Step 8 Locate and repair the short to ground in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring 7 Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 8 Replace the I/P Cluster. Refer to Instrument Panel Cluster (IPC) Replacement . Is the repair complete?

Related Content:

07tahoe dashboard repair kit, 1996 buick instrument cluster problems, 1999 yukon radiator removal instructions, 2006 buick torrent PRNDIL?, GM IPC CIRCUIT BOARDS

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to replace 2003 impala power steering pump, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, youtube replace the hub on a meritor ff981 axle, how to change power steering pump 2009 acada