92 escort relay box wiring diagrams

You search PDF repair manual about 92 escort relay box wiring diagrams, if there are search results will appear below. If search results do not exist, please search by others keyword.



  92 escort relay box wiring diagrams Direct Download speed 5432 Kb/s

  92 escort relay box wiring diagrams Full Version speed 8172 Kb/s



1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, 99 eldorado fuel pump relay test, where is the relay switch for liftgate in 2005 esclade, where is the washer relay located in a 2009 chevy impala, 1993 corvette power seat and power window shorting out breaker, sensor switch on rear beam axle of 2005 saturn relay, g5 sunroof relay

1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, toyota so5d engine fule pump control wireing diagram pdf, lucas cav injection pump diagram, how to change water pump on a dewoo, 89 dodge dakota fuel pump diagram, 2002 isx cummins manual pump installation, rager injection pump parts manual, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, isuzu dmax fuel pump, cav injector pump governor spring

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, zimmatic pivot wiring, free 1997 buick regal gs wiring diagrams, 1998 Dodge Dakota Service Manual, abs and Anti Theft Passive 2000 mercury cougar, 2003 s10 airbag wiring diagram, dodge durango 2002 suspension layout, 97 jetta fuel pump wiring diagrams, 1996 silverado electrical manual

1995 Volvo 850 L5-2.3L Turbo Relay Identification and Location

0

Filed Under (Volvo Manuals) by admin on 02-05-2012

download
Relay Identification and Location Relays Inside the Central Electrical Unit 101-102Control module, cruise control (4/3) 103 Fuel pump relay (2/23) 104,108Main headlight relay with bulb malfunction indicator (2/1) 105 Overload relay +X supply (2/30) 106 Overload relay +15 supply (2/31) 107 Overload relay +X supply (2/60) 201 Fog light relay (2/2) 202 Relay, deadlock setting (2/47) 203 Relay, windshield intermittent wiper (2/4) 204 Relay, tailgate intermittent wiper (2/16) 205-206Relay, central lock and delayed inside lighting (2/7) 207 Speed warning (2/51) or exhaust temp. sensor relay (2/15) 208 Relay, heated rear window and door mirrors (2/44) 210-211Relay, anti-theft alarm (2/28) 212 Relay, seat belt reminder/key warning (2/5) 213 Front fog lights, bridge (25/9) 214 Relay, heated rear seat (2/43) If the car is not equipped with a theft alarm, position 210 is bridged and 211 is unconnected. Relays Outside the Central Electrical Unit

Related Content:

diagram gearbox kancil

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

1983 monte carlo window wiring, 2005 ford ficm connector view, 3406e 1lw 40 pin wire, elect repair for cadillac dashboard replacement, kia besta wiring diagram, PIN DATA 2005 скачать, toyota alphard wiring diagram, vp44 9 pin connector, what pins are positve and negative on a 40 pin cat ecm

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, proper connection for horn relay 1968 chevelle, pcm drag adjustment, damaged fuel pump wiring, vcm ground wire, location of vent valve solenoid on 2010 ford ranger, 2005 tundra speed pulse signal wire location, 1998 s10 6 cylindes fuel regulator diagram

2005-2006 Toyota Tundra/ Sequoia 4.7L V8 MR Tech Power-flow Intake system Installation Manual

0

Filed Under (Toyota Manuals) by admin on 23-03-2012

download
The installation of this cold air intake does require mechanical skills. Removal of engine covers, air lines and removing several plastic plugs and screws that may be difficult. It is recommended that this system be installed by a professional mechanic. Be sure to disconnect the negative terminal before proceeding. Congratulations! You have just purchased the worlds first tuned intake system. MR Technology, Leading the way! Patent pending (A) and (G) (B) (D) (A) Power-Box contents: POWER-FLOW: An air intake evolution Tools required: 1- 8mm socket 1- 10mm socket 1- 12mm socket 1- Phillips screw driver 1- 8mm nut driver 1- 55mm allen wrench 1- Disc grinder or Dremel (C) (E) Figure 1 Figure 2 Carefully, remove the mass air flow sensor from the air sensor housing to be reused later in the instruc- tions. Unhook three spring clamps from the top air box cleaner. Once the hooks have been removed, continue to detach the air box top from the lower air box cleaner. See fig. 15 for better illustration. Once the nut and bolt have been removed, continue to remove the entire hose clamp. Unplug the electrical harness clip from the mass air flow sensor as shown above. Disconnect the 4mm vacuum line located to the side of the air box cleaner. Unscrew the nut and bolt the hose clamp that secures the hose over the radiator. Loosen the two flange nuts on the engine cover in order to remove the cover. Disconnec the 6mm vacuum hose that will be reused later in the instructions. Page 2 of Part# PF2019 Unscrew the two screws from the mass air flow sensor, shown above. Loosen the hose clamp on the air duct connected to the throttle body. Unplug the crank case breather hose from the air crank case port as shown above. >>> >>>> Figure 3 Figure 8 Figure 7 Figure 6 Figure 11 Figure 10 Figure 9 Figure 14 Figure 13 Figure 12 >>>> Figure 4 Figure 5 Once the flange nuts have been removed, continue to remove the cover from the engine compartment as shown above. >>> >>> >>> >>> >>> >>> The three spring clamps shown above are unhooked from the top air box cleaner (A). Remove the air filter panel once the top has been removed (B). Once the air filter panel is removed, there are three bolts that will be removed in order to detach the lower air box cleaner. Remove the entire lower air box cleaner from the engine compartment. Place the power bands over each end of the silicone elbow. press the short end of the silicone elbow over the throttle body. Once the silicone elbow has been aligned continue to semi-tighten power band over the throttle body end. The first vibra-mount is aligned to the pre-tapped hole located behind the head lamp. The first vibra-mount is now installed as shown above. Screw the second vibra-mount is aligned over the wheel well bracket. The second vibra-mount is now installed as shown above. The stock 6mm hose is removed from the fuel pressure regulator. Press the new 16″- 4mm vacuum hose over the fuel pressure regulator port. Page 3 of Part# PF2019 Figure 15 Figure 17 Figure 16 Figure 20 Figure 19 Figure 18 Figure 23 Figure 26 Figure 25 Figure 22 Figure 21 Figure 24 (B) (A) (A) (A) >>> >>> >>> >>> Both vibra-mounts are now installed, you are now ready to go on to the next step. Place one .462 and a .412 power band over the silicone step hose. Press the 3 3/4″ side over the velocity stack as shown above. The Power box is now sitting flush over the vibra- mounts and a fender washer is placed over each vibra-mount. The last m6 flange nut is placed over the vibra- mount located behind the Power box. The 65mm bolt is tightened with an allen wrench. The assembled power box is lowered into the engine compartment. Align the mounting points on the bracket arms over the vibra-mounts. One 45mm bolt is removed from the top of the box. The bracket is place under the Power box and the 45mm bolt is aligned and screwed back in place as shown above. Remove the 65mm bolt from the velocity stack base. Align the bracket to the hole and insert the 65mm bolt back in place

Related Content:

09 cts air condition drain location, 1990 isuzu npr no power to fuse panel, mercedes benz e280 w211 2005 fuse diagrams, hitatchi ex 200 fuse box order, install 2000 celica air box, land rover freelander 2 2007 fuse box, Popping noise from air filter, replace tacoma ac drain hose, troubleshooting a mazda 6 air conditioner drain line, turn signal fuses on 2002 winnebago adventurer

2010 TOYOTA PRIUS FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
Items required for installation: Push pin 10mm bolt 10mm nut TOYOTA PRIUS 2010 FOG LAMP KIT 1 of 4 01-25-2010 STEP 3.2 • Attach fog lamp to bezel. STEP 3.3 • Fog lamp and bezel assembly. STEP 3.4 • Place fog lamp and bezel assembly onto vehicle. Fasten fog lamp to vehicle with 10mm nut and supplied screw. ( Repeat step 3 for passenger side ) STEP 4.0 Removal of interior trim on driver side STEP 4.1 • Pull up on lower door trim. STEP 4.2 • Foot panel-Remove 16mm plastic nut. STEP 4.3 • Pull foot panel inward toward center console. STEP 4.4 • Remove screw. STEP 4.5 • Disconnect hood release cable from latch by pulling down on the black cable freeing it from its location. Then moving the cable to the left away from the mounting bracket. STEP 4.6 • Remove cable from latch. STEP 4.7 • Pull lower left interior panel away from dash and unplug connectors. CAUTION! You may damage wiring and connectors if you pull too hard. Driver side interior removed. 2 of 4 01-25-2010 STEP 4.8 • Remove two screws and push back on tab to free lower panel. STEP 4.9 • Unplug connector and wire harness from panel and remove panel by pulling it toward the driver seat. STEP 5.0 Fog lamp switching wiring • Run WHITE wire through V-channel and pull female bullet connector end towards fire wall. • Connect ground wire to dashboard frame. STEP 5.4 • Plug green connector into fog lamp switch. (Plug all connectors removed from Step 4 and place panel back in position) STEP 6.0 Fog lamp wiring harness • From the panel removed under the steering wheel locate hole in grommet. STEP 6.1 • Puncture hole with O-ring pick/Philips screw driver or any sharp object no larger that the black tubing. (You want a tight seal between grommet and wire). STEP 5.1 • Remove tape from lower connector on ECU and locate BROWN wire. Use the bridge connector to connect RED wire to BROWN wire. You may need to cut RED wire to proper length. STEP 5.2 • Remove. STEP 5.3 • Replace with fog lamp switch. STEP 6.2 • Insert coat hanger or welding rod through punctured hole. Push rod far enough into engine compartment so you can retrieve it. STEP 6.3 • Bend tip or rod with needle nose pliers. STEP 6.4 • Insert hook end into bullet connector making sure black tubing is close to rod. V-channel Ground 3 of 4 01-25-2010 STEP 6.5 IMPORTANT! Wrap electrical tape around connector, tubing and rod. It is important that all three be secured as one unit so not to rip connector from wiring. You want tubing to take as much of the pull force as possible. STEP 6.6 • Apply soapy water to the entire length of black tubing and from the inside of the vehicle pull rod until wire breaks through grommet. 2.5-3ft of wiring should be sufficient. STEP 6.7 • Run wiring along side the black tube indicated until it meets female end of the WHITE fog lamp wire switch. STEP 6.8 • Connect both ends together and tie strap wiring to black tube. STEP 6.9 • On the top left corner of the fuse box (to the right of the brake fluid reservoir) locate silver ECU mounting bracket. STEP 6.10 • Remove 10mm bolts and attach BLACK ground and relay as indicated. STEP 6.11 • Attach harness connector to relay. STEP 6.12 • Run wire harness between ECU and fuse box. Run RED power wire along the same path as WHITE power wire in fuse box. Connect RED power wire to 12V power source directly above WHITE cable. STEP 7.0 Connecting wire harness to fog lamps • Run wiring for driver and passenger side lamps down toward driver side fog lamp. • Connect shortest harness to driver side fog lamp. Run wire harness alongside turn signal harness. • Use the supplied tie straps to secure passenger side wire harness along the radiator support frame shown. • Connect harness to fog lamp • END of installation

Related Content:

2010 prius fuse locations, Toyota Prius 2010 service manual, removing starter from 2005 crv, REMOVE AND REPLACE 2005 HONDA CRV STARTER, prius 2010 fuel pump fuse, kia rip radiator hose, ignition wire set 8MM Kia Sportage 2010 LX, how to change thermostat c arcadia, How do I remove the starter on a Chevy Cobalt 2006, Honda malfunction reset button location

Toyota Celica 1.8L 16v VVTi INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
1. Disconnect the negative terminal from the vehicle battery. 2. Unclip & remove the plastic trim from the front slam panel. (Fig. 1) 3. Unclip & remove the electrical harness plug from the MAS (Mass Air Sensor). (Fig. 2) 4. Unclip the MAS harness from the side of the air box. (Fig. 3) 5. Unclip & remove the intake hose from the MAS / air box lid. (Fig. 4) 6. Remove the vacuum hose from the inlet manifold (small rubber hose between the air box & manifold. (Fig. 5) 7. Fit the rubber blanking plug to the vacuum pipe located on the inlet manifold (ensure an air tight seal. (Fig. 6) 8. Unclip & remove the CFSV (carbon filter solenoid valve) from the air box lid. (Fig. 7) 9. Remove the 2 bolts securing the air box assembly & carefully lift out the assembly (Do not fully remove at this time). (Fig. 8&9) 10. From underneath the air box assembly unclip the blue electrical harness plug from the VSV (Vacuum solenoid valve). Now fully remove the air box assembly. (Fig.10) 11. Refit the plastic trim to the slam panel. 12. Remove the plastic ducting from between the fan cowling & ECU cover. (Fig.11&12) 13. Unclip & remove the intake hose from the throttle housing. (Fig.13) 14. Remove the bolt securing the relay unit to the chassis leg as shown. (Fig.14) 15. Secure the new mounting bracket to the relay mounting point located on the chassis leg using the M8 bolt & washer supplied. (Fig.15) 16. Clip the edge trim to the outside edge of the heat shield, cut away any excess trim. (Fig.16) 17. Attach the heat shield to the mounting bracket & secure using the M6 allen head bolts, nylock nuts & washers supplied. (Fig.17) 18. Unscrew & remove the bracket from the CFSV. (Fig.18) 19. Fit the new ‘L’ mounting bracket to the CFSV using the original screw. (Fig.19) 20. Secure the CFSV / mounting bracket to the side of the heat shield using the M5 bolt, nylock nut & washers supplied. (Fig.20) 21. Carefully unscrew & remove the MAS from the air box assembly. (Fig.21) 22. Stick the foam gasket to the hole located on the new molded intake pipe. Fit the MAS to the hole in the molded intake pipe & secure using the screws supplied. (Fig.22&23) 23. Assemble the new molded intake pipe using the silicone adaptor hose & rubber filter adaptor. (Fig.24) 24. Fit the new K&N filtercharger to the rubber filter adaptor & secure using the hose clamp supplied. (Fig.25) 25. Secure the new intake pipe assembly to the throttle housing using the stepped silicone hose & hose clips supplied (align the notch on the intake pipe with the notch on the throttle housing). (Fig.26) 26. Reconnect the electrical harness plug from the MAS. (Fig.27) 27. Secure the coolant hose & any excess harnesses using the plastic ties supplied. 28. Reconnect the negative battery terminal. 29. Carry out a final check of the alignment / fitment of the K&N induction system. Make any adjustments utilizing the slotted holes on the brackets & shield. Installation is now complete. (Fig.28

Related Content:

drawing mounting between intake manafold and block toyota 22R-E motor, heat sheilds on 2000 celica location, how to remove ecu 1992 toyota celica

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 2005 honda crv malfunction indicator lamp reset, 2003 buick lesabre lose power for instrument panel and a/c controls, 1995 accord repair manual pdf, 1989 corvette climate control panel, replacement instructions cruise control module civic, honda intergrated control unit tail lights, honda accord cooling fans, honda accord code 61-1

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, 99 eldorado fuel pump relay test, where is the relay switch for liftgate in 2005 esclade, where is the washer relay located in a 2009 chevy impala, 1993 corvette power seat and power window shorting out breaker, sensor switch on rear beam axle of 2005 saturn relay, g5 sunroof relay