Skip to content

96 honda civic left front door wiring harness

You search PDF repair manual about 96 honda civic left front door wiring harness, if there are search results will appear below. If search results do not exist, please search by others keyword.

1996-2000 Honda Civic Door Panel REMOVAL And INSTALLATION Manual

download
Honda Door Panel 96-00 Civic REMOVAL & INSTALLATION Remove the screw from behind the interior door handle Slide out the door handle trim as shown Removing the door panel from the passenger side door View of the inside of the door, panel removed 1. Remove the screw from the door handle trim. 2. Slide the handle assembly forward and out to access the lock rod clip. 3. Release the clip 4. Disconnect the door lock switch 5. Remove the door opener handle assembly. 6. Carefully pry at the small opening on the bottom of the speaker grill. 7. Remove the speaker grille. 8. Remove the speaker mounting screws. 9. Detach the electrical connector and remove the speaker. 10. Remove the screws in the armrest. 11. Remove the center from the trim clip at the upper front of the door panel and remove the clip. 12. Using a suitable trim panel removal tool, unsnap the door panel from the door frame. 13. Carefully lift the door panel up and away from the door frame. To install: 14. Installation is the reverse of the removal procedure. Honda Civic/Del Sol 1996-2000 Electric Window Motor REMOVAL & INSTALLATION 1. Remove the regulator from the door assembly. 2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7/ 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized. 3. Drill out the ends of the motor attaching rivets using a 1/ 4 in. (6mm) bit. 4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly. Regulator and motor assembly—except rear doors Secure the rivets by collapsing the rivet ends using a ball peen hammer To install: 5. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer. 6. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle’s window motor harness) to rotate the regulator, providing access to the remaining rivet. 7. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet. 8. Install the regulator to the door assembly.

1996 – 2000 Civic 2-door Front Windows Bind or Have Come Out of the Run Channel Repair Manual

download
REPAIR PROCEDURE 1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual. 2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator. 3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot. 4. Check the year and VIN. If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5. If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8. 5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts. 6. Disconnect the power window motor connector, and detach the harness clip (if applicable); then lift and remove the regulator through the opening in the door. 7. Install the new regulator in the door, then loosely install the two rear mounting bolts and the two roller guide bolts. Do not tighten the two front mounting bolts yet. Go to step 9. 8. Loosen the window regulator’s two rear mounting bolts, two front mounting bolts, and two roller guide bolts

2009 HONDA CIVIC 4-DOOR FLOOR MATS INSTALLATION INSTRUCTIONS

download
INSTALLATION NOTE: Floor mat anchors are required for the driver’s side of the vehicle; these anchors prevent the front floor mat from sliding forward and possibly interfering with the pedals. If you remove the front floor mat, make sure you reanchor it when you put it back in your vehicle. If you replace the floor mat, use factory floor mats designed to be used with the floor mat anchors. If you use a non-factory floor mat in the driver’s footwell, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional mats on top of the anchored mat. Additional mats may slide forward and possibly interfere with the pedals. Identify each floor mat by the marks on the back of each mat: the floor mats marked “R” or “Passenger’s side” go on the right side of the vehicle; the floor mats marked “L” or “Driver’s side” go on the left side

2009 HONDA CIVIC 2-DOOR (DX, LX) BASS SPEAKER SYSTEM INSTALLATION INSTRUCTIONS

download
INSTALLATION 1. Make sure you have the anti-theft codes for the audio unit, then write down the audio presets. 2. Disconnect the negative cable from the battery. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 871504AH BASS SPEAKERS BASS UNIT 3. Open the trunk lid. Pull the release handle on the bottom of the rear shelf to tilt the rear seat to the front. 4. Remove the trunk spring protector (four clips). 871505AH RELEASE HANDLE FRONT REAR SEAT 871506AH REAR SHELF TRUNK SPRING PROTECTOR 4 CLIPS FRONTIn the trunk, unplug the vehicle 2-pin connector from the high-mount brake light. 6. Remove the rear speaker tray (10 clips and four tabs) while lightly pulling up the end of the rear speaker tray as shown. •Attach clips left on the vehicle panel onto the rear speaker tray. 871507AH FRONT HIGH-MOUNT BRAKE LIGHT 2-PIN CONNECTOR TRUNK LIGHT REAR SHELF 871508AH REAR SPEAKER TRAY FRONT 10 CLIPS 4 TABS Installing the Bass Speakers 7. Remove the right and left vehicle speakers (two tabs and one screw for each speaker). 8. Install the right and left bass speakers using the screws removed in step 7

2009 HONDA CIVIC 2-DOOR EX-L FOG LIGHTS INSTALLATION INSTRUCTIONS

download
Illustration of Fog Lights Installed on the Vehicle EX-L model 851302AK RELAY SUB HARNESS SWITCH HARNESS COMBINATION LIGHT SWITCH LEFT FOG LIGHT FOG LIGHT HARNESS RIGHT FOG LIGHT 20 A FUSE INSTALLATION 1. Make sure you have the anti-theft codes for the audio system and navigation system (if equipped), then write down the radio presets. 2. Disconnect the negative cable from the battery. 3. Remove the radiator cover (two expansion clips and two clips). Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.