96 toyota tacoma timing removal

You search PDF repair manual about 96 toyota tacoma timing removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  96 toyota tacoma timing removal Direct Download speed 5432 Kb/s

  96 toyota tacoma timing removal Full Version speed 8172 Kb/s



TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 13-07-2012

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture

2002 Toyota Truck Tundra Access Cab SR5 2WD Timing Belt Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 09-06-2012

download
2002 Toyota Truck Tundra Access Cab SR5 2WD V6-3.4L (5VZ-FE) Copyright © 2008, ALLDATA 9.50 Page 2 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DISCONNECT UPPER RADIATOR HOSE 4. DISCONNECT PS PUMP FROM ENGINE a. Disconnect the 2 PS air hoses from the air intake chamber and resonator. b. Remove the bolt holding the PS pressure tube clamp to the frame. c. Remove the drive belt. d. Remove the bolt and nut, and disconnect the PS pump from the engine. 5. w/ A/C: DISCONNECT A/C COMPRESSOR FROM ENGINE a. Disconnect the A/C compressor connector. b. Remove the drive belt. c. Remove the 4 bolts, and disconnect the A/C compressor from the engine. 6. LOOSEN FAN WITH FLUID COUPLING AND FAN PULLEYS 7. REMOVE DRIVE BELT FOR GENERATOR 8. REMOVE NO.2 FAN SHROUD 9. REMOVE FAN WITH FLUID COUPLING AND FAN PULLEYS 10. w/ A/C: REMOVE A/C COMPRESSOR BRACKET Remove the 5 bolts and A/C compressor bracket. 11. DISCONNECT UPPER RADIATOR HOSE 12. REMOVE NO.2 TIMING BELT COVER a. Disconnect the camshaft position sensor connector from the No. 2 timing belt cover. b. Disconnect the 4 high-tension cord clamps from the No. 2 timing belt cover. c. Remove the 6 bolts and timing belt cover. 13. REMOVE FAN BRACKET a. Remove the nut and PS pump adjusting strut. b. Remove the bolt, nut and fan bracket. 14. SET NO. 1 CYLINDER AT TDC/COMPRESSION a. Turn the crankshaft pulley and align its groove with timing mark “0″ of the No. 1 timing belt cover. b. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°) . HINT: When re-using timing belt: Place the matchmarks on the timing belt and camshaft timing pulleys, and place matchmark on timing belt to match the end of the No. 1 timing belt cover. 15. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot. 16. REMOVE TIMING BELT

Related Content:

toyota tacoma 2000 REMOVE COMPRESSOR DRIVE BELT, 2002 ford ranger 2 3L timing tool, 2002 nissan altima changing camshafts, 2002 toyota tundra manual, Centurial Timing Module

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, toyota sienna grill removal, 4k carburetor manual, how to remove center console 2013 camry, 2005 tundra grill removal, toyota 4k carburetor service manual, how to check windshield wiper motor and arm on a 2007 malibut, how remove intake plenum on 1998 Toyota sienna

1994 Toyota Camry DX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 22-01-2012

download
Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of way. On Camry, remove coolant reservoir tank if it interferes with timing belt removal. Remove engine control (torque) rod from front of engine. 3. On all models, remove accessory drive belts. Using floor jack, slightly raise engine to remove weight from right (timing belt side) engine mount at timing belt cover. 4. Remove right (timing belt side) engine mount and bracket from front of engine. Remove spark plugs. Remove No. 2 timing belt cover and gaskets. See Fig. 1 . 5. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. 6. Ensure timing mark on crankshaft pulley aligns with “0″ mark on No. 1 timing belt cover. Ensure hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If hole in camshaft sprocket is not aligned with alignment mark, rotate crankshaft clockwise one full revolution. 7. Loosen No. 1 idler pulley bolt. See Fig. 1 . Move No. 1 idler pulley outward, away from timing belt as far as possible. Temporarily retighten No. 1 idler pulley bolt. Remove timing belt from camshaft sprocket. 8. Using Pulley Holder (SST 09213-54015) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. 9. Using gear puller, remove crankshaft pulley. Remove No. 1 timing belt cover and gasket. Note direction of timing belt guide installation. See Fig. 1 . Remove timing belt guide. 10. Loosen No. 1 idler pulley bolt. See Fig. 1 . Remove timing belt from crankshaft sprocket. Remove idler pulleys (if necessary).

Related Content:

96 Toyota Camry 3 0 Timing Marks, TOYOTA 4Y TIMING MARKS, toyota 7A-FE timing belt alignment marks, Toyota Camry Crankshaft Pulley Removal

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

0

Filed Under (Daewoo Manuals) by admin on 13-05-2011

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

Related Content:

2006 kia sedona 3 8 engine timing mark, 02 is 300 lexus tsib vvt-i pulley installation, 2002 jetta crank mark, 2003 eclipsed2 4 litre cranckshaft position sensor location, 3126 timing pin hole, 91 honda accord timing belt marks diagram, 98 eclipse rs service manual, changing timing belt 2004 kia optima EX 2 7 6 cylinder ?, how to adjust belt on 2001 kia optima, kia rio 5 2007 timming belt

TOYOTA AND LEXUS HIGHLANDER HYBRID REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-03-2012

download
Engine and Vehicle Identification Chart………………………………………..4-2 General Engine Specifications………4-2 Engine Tune-Up Specifications……..4-2 Capacities ………………………………….4-3 Valve Specifications …………………….4-3 Crankshaft and Connecting Rod Specifications……………………..4-3 Camshaft and Bearing Specifications ……………………………4-4 Piston and Ring Specifications……..4-4 Torque Specifications………………….4-4 Wheel Alignment ………………………..4-5 Tire, Wheel and Ball Joint Specifications ……………………………4-5 Brake Specifications ……………………4-5 Scheduled Maintenance Intervals……………………………………4-6 STEERING AND SUSPENSION ………………4-28 A Air Bag…………………………………….4-28 Disarming ……………………………4-28 Precautions ………………………….4-28 Alternator …………………………………..4-7 B Brake Caliper ……………………………4-30 Removal And Installation……….4-30 C Camshaft and Valve Lifters…………4-14 Inspection ……………………………4-16 Removal & Installation…………..4-14 CV-Joints………………………………… 4-24 Overhaul ……………………………..4-24 Cylinder Head …………………………..4-10 Removal & Installation…………..4-10 D Disc Brake Pads………………………..4-32 Removal And Installation……….4-32 E Engine Assembly ………………………..4-7 Removal & Installation…………….4-7 Exhaust Manifold ………………………4-12 Removal & Installation…………..4-12 F Front Crankshaft Seal………………..4-14 Removal & Installation…………..4-14 Front Halfshaft………………………….4-23 Removal & Installation…………..4-23 Front Strut ……………………………….4-28 Removal & Installation…………..4-28 Front Wheel Bearing………………….4-29 Fuel Filter ………………………………..4-21 Fuel Injector……………………………..4-22 Removal & Installation…………..4-22 Fuel Pump ……………………………….4-21 Removal & Installation…………..4-21 Fuel System Pressure………………..4-21 Relieving ……………………………..4-21 H Heater Core………………………………..4-7 Removal & Installation…………….4-7 Hybrid Transaxle Assembly…………4-22 Removal & Installation…………..4-22 I Ignition Timing ………………………….. 4-7 Adjustment…………………………….4-7 Intake Manifold …………………………4-11 Removal & Installation…………..4-11 L Lower Ball Joint………………………..4-29 Removal & Installation…………..4-29 Lower Control Arm……………………4-29 Removal & Installation…………..4-29 O Oil Pan…………………………………….4-18 Removal & Installation…………..4-18 Oil Pump …………………………………4-18 Removal & Installation…………..4-18 P Pinion Seal ………………………………4-27 Removal & Installation…………..4-27 Piston and Ring………………………..4-21 Positioning ………………………….4-21 Power Rack And Pinion Steering Gear…………………………..4-28 Removal & Installation…………..4-28 R Rear Halfshaft………………………….. 4-24 Removal And Installation……….4-24 Rear Main Seal…………………………4-19 Removal & Installation…………..4-19 Rear Strut…………………………………4-28 Conventional Strut Overhaul…..4-28 Removal And Installation……….4-28 Rear Traction Motor…………………..4-22 Removal & Installation…………..4-22 Rear Wheel Bearing…………………..4-29 Removal And Installation……….4-29 T Timing Belt ………………………………4-19 Removal & Installation…………..4-19 V Valve Lash ……………………………….4-17 Adjustment…………………………..4-17 W Water Pump ……………………………..4-10 Removal & Installation………..

Related Content:

how to install running boards on honda pilot, nissan ka20 16 valve cyl head gasket replacement, 2001 chevrolet monte carlo radiator removal, zx2 vct replacement instructions, nissan ka20 timing marks, 2002 highlander brake torque, 2006 sienna liftgate struts replacement video, Toyota 14b engine torque specification for cylinder head big end and valve clearance, quicksilver isolators pdf, replace alternator on honda ridgeline

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to remove 2011 dodge durango grill, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

1994 Mitsubishi Expo LRV TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 30-04-2012

download
Removal 1. Remove radiator shroud, cooling fan and pulley. Remove all drive belts and crankshaft pulleys. Remove upper timing belt covers and gaskets. Note bolt length and location. 2. Remove crankshaft sprocket bolt and washer. Rotate crankshaft clockwise (as viewed from timing belt end of engine) until cylinder No. 1 is at TDC of compression stroke. Align timing mark on camshaft sprocket with mark on cylinder head. See Fig. 5 . 3. Loosen timing belt tensioner adjustment bolt, and move tensioner toward water pump. Tighten bolt to secure tensioner. Remove front timing belt and tensioner. DO NOT rotate crankshaft after timing belt has been removed. 4. Remove camshaft sprocket (if necessary). Remove oil pump sprocket access plug from cylinder block. See Fig. 4 . Insert a .31″ (8.0 mm) diameter Phillips screwdriver to block left silent shaft. 5. Remove oil pump sprocket nut, and remove sprocket. Remove front crankshaft sprocket and flange. Note direction and order of installation for reassembly reference. 6. Remove rear timing belt tensioner assembly. Remove rear timing belt. Remove right silent shaft sprocket with spacer (if necessary). Remove rear crankshaft sprocket with key Installation 1. Install rear crankshaft sprocket and flange. Install right silent shaft sprocket and spacer. Spacer should be installed with chamfered end into oil seal. Align timing marks. See Fig. 5 . 2. Install rear tensioner. Hold tensioner tightly against belt while tightening bolts. Ensure deflection is .20- .28″ (5.0-7.1 mm). See Fig. 6 . Install camshaft sprocket. Tighten camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS . 3. Install front timing belt tensioner, tension spring and spacer. Ensure spring is properly engaged against water pump case. Rotate tensioner toward water pump, and temporarily tighten bolts. Ensure timing marks are aligned. See Fig. 5 . Install timing belt on crankshaft. 4. Apply pressure on tension side of timing belt while installing belt (in order) on crankshaft, oil pump and camshaft sprockets. Loosen tensioner to apply spring pressure to timing belt. 5. To apply tension to belt, rotate crankshaft clockwise until camshaft sprocket timing mark is offset by 2 teeth. Tighten tensioner bolt. Tighten tensioner spacer nut

Related Content:

04 volvo s60 2 5t how to align cam shafts to cam sprockets, adjusting cam sprockets, chrysler sprocket removal tool, ej25d enigine TORQUE, what are torque values for 2 2ecotec cam sprokets

Related Content:

ford E250 rear vaporline to carben canester diagram, 2008 mazda 2 3 timing procedure, 1999 honda odyssey repair manual pdf, NTC350 drive gear remova, remove head timing cover on a 96 altima, remove timing cover 2005 Nissan Altima 2 5 L, removing pulleys timing belt cover 3000 gt, set timing on 2005 aveo, timing marks for 2005 nissan altima 2 5, Variable Camshaft Timing Solenoid Picture