98 monte carlo 3400 engine diagram

You search PDF repair manual about 98 monte carlo 3400 engine diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  98 monte carlo 3400 engine diagram Direct Download speed 5432 Kb/s

  98 monte carlo 3400 engine diagram Full Version speed 8172 Kb/s



2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

2000 Nissan sentra 1 8 engine bolt torque diagram, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, 6m70 service manual obd codes pdf, 2005 chevy impala motor diagram, Position of sensors in mitsubishi 4m 51 engine, mitsubishi 4m51 engine wiring diagram, TOYOTA SO5D SERVICE MANUAL, perodua engine overhall pdf, 4EFE engine manual

1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, crank sensor location on 6 7 power stroke, 2001 saturn fluid light comes on, Replace 2011 buick regal ambient temp sensor, 2002 rendezvous radiator repair

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, 2001 a4 oil cooler lines, 2012 kia srento a/c condensor drain line drawing, 2006 impala oil filter housing gasket, oil cooler on 3406 cat how to change, 2006 chevy trailblazer engine removal, removing the oil pan on a 2008 impala 3 5, 2005 ford escape 2 3liter oil dipstick housing seal, clips for blazer oil cooling lines, oil flow path for 5 3 chevrolet

EDELBROCK ENGINE MOUNT ADAPTER PLATES For Converting Small Block Chevy Applications to LS1 INSTALLATION INSTRUCTIONS

0

Filed Under (Chevy Manuals) by admin on 27-12-2011

download
PRE-INSTALLATION PROCEDURE General Motors vehicles came with many different engine and transmission combinations. This section is intended to verify that all the correct components are in place prior to installation. If the vehicle is currently equipped with a small block Chevrolet V8, then the engine isolator for the current application will work with the Edelbrock Adaptor plates. See the next page for further notes on various applications. A-BODY APPLICATIONS: 1964 – 1967: Vehicles that are being converted from six cylinder or a non-Chevrolet engine can use engine frame stands for the 283 to 327 from a salvage yard or reproduction suppliers such as OPGI and Yearone; engine isolators can be of the OEM rubber type from a parts supplier or polyurethane safety mounts from Energy Suspension: part #3.1114 (zinc plated), or #3.1115 (chrome). 1964 – 1967 applications will require mildly slotting the engine frame stand mounting holes, as shown in Figures 1 and 2. FIGURE 1 FIGURE 2 – 1968 – 1972: From 1968 to 1972, Chevrolet used two different frame stands with matching engine isolators. Type one is the 307 (and some early 1968 327′s), while type two includes all engines from the later 1968 327′s through to the 454, encompassing all engine sizes in-between. If you have obtained frame stands from another vehicle, use the following procedure to identify your mount system: measure the ears of the engine isolator where the engine mounting bolt goes, the inside dimension is 2 5/8″for the 307 cid (Figure 3) and 2 3/8″for the larger sized engine (Figure 4). Frame stands for the late 327,350 to 454 are also available from reproduction suppliers such as OPGI and Yearone, engine isolators can be of the OEM rubber type from a parts supplier or polyurethane safety mounts from Energy Suspension: part #3.1114 (zinc plated) #3.1115 (chrome) for the 307, part #3.1117 (zinc plated) or #3.1118 (chrome) for the late 327 to the 454. FIGURE 3 (307) FIGURE 4 (350 et al) F-BODY AND X-BODY APPLICATIONS: 1967 – 1969 F-body and 1968 – 1974 X-body: Vehicles that are being converted from six cylinder or a non-Chevrolet engine will require engine isolators that match the engine frame stand. There are a variety of styles depending on engine size and model year, so get the engine isolators and frame stands which are available from reproduction suppliers such as Classic Industries and Yearone. Engine isolators can be of the OEM rubber type from a parts supplier or polyurethane safety mounts from Energy Suspension. There are two basic types of engine isolators; to identify them measure the distance between the tab for the engine mount through bolt, if it is 2-5/8″use Energy Suspension #3.1114 (zinc plated) #3.1115 (chrome), if the distance is 2-3/8″use #3.1117 (zinc plated) #3.1118 (chrome).

Related Content:

what does the s stand for in jaguar s type

1999-2006 Volkswagen A4 Engine Speed Sensor G28 Checking

0

Filed Under (Volkswagen Manuals) by admin on 31-01-2011

download
Special tools, testers and auxiliary items required Multimeter . Wiring diagram. Test requirements The Motronic Engine Control Module (ECM) J220 fuses OK. Battery voltage at least 12.5 volts. All electrical consumers such as, lights and rear window defroster, switched off. Vehicles with automatic transmission, shift selector lever into position “P” or “N” . A/C switched off. Ground (GND) connections between engine/transmission/chassis OK. Ignition switched off. Test procedure Perform a preliminary check to verify the customers complaint. Refer to Preliminary Check Start diagnosis The Engine Speed (RPM) Sensor G28 detects RPM and reference marks. Without an engine speed signal, the engine will not start. If the engine speed signal fails while the engine is running, the engine will stop immediately Function test Connect the scan tool. Switch the ignition on. Using the scan tool, check the engine speed: End diagnosis and switch ignition off. If the specified value was not obtained: Checking internal resistance Disconnect the gray Engine Speed (RPM) Sensor G28 electrical harness connector 7 arrow 7 . Using a multimeter , check the Engine Speed (RPM) Sensor G28 terminals 2 to 3 7 see insert 7 for resistance. Specified value: 0.7 to 1000 kOhm Check Engine Speed (RPM) Sensor G28 terminals 1 to 2 and 1 to 3 for short circuits. Specified value: ? (infinity) If any of the specified values are not obtained: Replace the Engine Speed (RPM) Sensor G28 . Refer to Engine Mechanical, Fuel Injection and Ignition 7 Repair Group 13 . If the specified values are obtained: Checking wiring If the manufacturers test box is being used. Perform the following step. Install the test box Adapter F/VAG1598 (68 Pin) VAG1598/22 . If the manufacturers test box is not being used. Perform the following step. Remove the Motronic Engine Control Module (ECM) J220 . Refer to Motronic Engine Control Module J220, Replacing .

Related Content:

G28 Engine Speed Sensor where to buy, g28 resistance value bvk engine, G28 Sensor VW

2003 Mercedes Benz CLK 500 Engine Controls Cooling Fan Runs Continuously

0

Filed Under (Mercedes-benz Manuals) by admin on 12-05-2012

download
Engine Fan Runs Constantly If you receive customer reports in the above model vehicles of the engine fan running constantly with code P2073(004) Electric fan for engine & AC, open circuit; this may be caused by the wiring harness between the ECU and the engine fan or the engine control unit fan end stage malfunctioning. To resolve, perform the below procedure. Note: Only vehicles as outlined in Service Campaign Bulletin No. 2003110006 are affected, see vehicle range shown. When performing Service Campaign Bulletin No. 2003110006 only, the engine ECU does not need to be exchanged. All engine ECUs exchanged under warranty for the above condition must be accompanied by the freeze frame data for the respective DTC. Claims submitted without this information will be debited back to the dealer Remedy: 1) Check wiring harness between engine ECU connector (pin 39) and engine fan connector (pin 4) for continuity. IF OK, proceed as follows. 2) Replace engine control unit (AR07.08-P-7008P) 3) Install adapter harness a. Remove lower underbody panel b. Disconnect engine wiring harness plug from engine fan C. Connect adapter wiring harness between fan connector and engine wiring harness. d. Secure adapter wiring harness with loom ties (Figure 1). e. Secure adapter wiring harness plug to engine fan (Figure 2)

Related Content:

2002 aztek fuel pump harness connector, 2006 mack granite cv 713 ac pressure switche, 94 buick lesabre wiring diagram coolant fan, clk 500 engine fan removal, cooling fan installation 91 corvette

1998 Ford Escort ZX2 L4-2.0L DOHC Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures

0

Filed Under (Ford Manuals) by admin on 06-05-2012

download
PROCEDURE FOR 2003 ESCORT ZX2 PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER ^DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. Zoom Sized for Print 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)) 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1). 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4) 10. Remove original front and rear engine support cross-member bushings (Figure 3). Zoom Sized for Print a. Modify two (2) new Front-Upper Engine Support Cross-Member Bushings only (F7CZ-6A061-AA) by removing approximately 1/4″ (6 mm) of material from two (2) sides of the upper bushing. Use a utility knife or hack saw to achieve desired shape (Figure 2). b. Reinstall front attaching point of engine support cross-member with the original two (2) bolts, two (2) new Lower Bushings (F7CZ-6A061-BA), and two (2) new Upper Bushings (F7CZ-6A061-AA) that were modified in Step A (Figure 3). Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts. c. Reinstall rear attaching point of engine support cross-member using new Bushings (F7CZ-6A061-BA and F7CZ-6A061-AA) and original nuts (Figure 3). Both rear position upper bushings must be installed in “AS IS” condition (UNMODIFIED). d. Torque the retaining nuts and bolts to 64-89 N.m (47-65 lb-ft.). 11. Reinstall the front attaching points of the Belly Band with the original two (2) bolts. Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts (Figure 1). 12. Reinstall rear-attaching points of the Belly Band with original two (2) nuts (Figure 1). 13. Torque the retaining nuts and bolts to 64-89 N-m (47-65 lb-ft.)

Related Content:

2004 chevy colorado 3 5 camshaft actuator, 2002 ford escort manual pdf

1999 Volkswagen New Beetle GL timing belt replacement manual

0

Filed Under (Volkswagen Manuals) by admin on 21-06-2012

download
REMOVAL & INSTALLATION NOTE: For 2004, manufacturer does not provide a timing belt replacement interval. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Engine code AEG is stamped into machined pad on front of cylinder block above crankcase breather, near cylinder head mating surface. See Fig. 1 . For all other 2.0L engines, engine code is stamped on transmission mating flange at the rear of the engine. See Fig. 2 . For all engines, code can also be found on the vehicle data plate and on a sticker on the timing belt cover. Fig. 2: Locating Engine Identification Code (AVH, AZG, BDC & BEV) Courtesy of VOLKSWAGEN UNITED STATES, INC. TIMING BELT Removal (AEG, AVH, AZG, BEV & BDC Engine Codes) 1. Remove right hand insulation tray from engine compartment. Remove engine cover. Rotate serpentine belt tensioner clockwise to relieve belt tension. Remove serpentine belt. See Fig. 3 . Lock in place using Mandrel (T10060) or a drift. Fig. 3: Releasing Serpentine Belt Tensioner Courtesy of VOLKSWAGEN UNITED STATES, INC. 2. Remove serpentine belt tensioner assembly. See Fig. 4 . Turn crankshaft to TDC position. See Fig. 5 . Align TDC marks visible in bellhousing access hole. See Fig. 6 . Remove upper timing belt cover. Ensure camshaft sprocket timing mark aligns with mark on rear cover. See Fig. 5 . 3. Support engine from above or below with floor jack to take engine weight off of mounts. Remove coolant reservoir and set aside. On Golf and Jetta, remove power steering reservoir (hoses attached), and set aside. On New Beetle, pull off EVAP hoses at EVAP canister and throttle valve housing. 4. On all models, remove engine mount from timing belt end of engine. See Fig. 7 . Remove crankshaft pulley from crankshaft sprocket. It is NOT necessary to remove center bolt (center bolt is torque-to-yield type that must be replaced if removed). 5. Remove timing belt covers. Remove engine support from front of engine. See Fig. 4

Related Content:

2004 volkswagen jetta timing belt replacement interval

1998 Ford Escort Diagnose and repair idle vibration conditions by referring to the following idle vibration Service Procedures

0

Filed Under (Ford Manuals) by admin on 30-04-2012

download
PROCEDURE FOR 2003 ESCORT ZX2 PROCEDURES FOR 1997-2002 ESCORT, ESCORT ZX2 AND TRACER ^DRIVEABILITY – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY ^ENGINE – IDLE VIBRATION – VEHICLES EQUIPPED WITH 2.0L SPI OR ZETEC ENGINE ONLY 1. Neutralize engine mounts only. Refer to appropriate model year Noise, Vibration and Harshness (NVH) Workshop Manual Section 100-04. 1. Shift the transaxle into Neutral and apply the parking brake. 2. Remove battery and battery tray. 3. Support engine with Three-Bar Engine Support Tool (Rotunda 303-D063) and Lifting Brackets (Rotunda 303-050). 4. Raise vehicle. Refer to the appropriate model year Workshop Manual, Section 100-02. Zoom Sized for Print 5. Remove the rear lower cross-member (attached with four (4) bolts (Figure 1)) 6. Remove the engine support cross-member that runs from front to rear of the engine (Belly Band). This can be accomplished by removing the front two (2) attaching bolts, the rear two (2) attaching nuts and the four (4) Engine Mount # 1 and # 2 nuts (Figure 1) 7. Modify the Belly Band on the two rear attaching Engine Mount # 1 holes by slotting the holes approximately 1/4″ (6 mm) in a front to rear direction. Use a Drill Bit (Figure 7). 8. Loosen the center bolt on the # 1 (rear) lower Engine Mount (Figure 4). 9. Loosen the center bolt on the # 2 (front) lower Engine Mount (Figure 4) a. Modify two (2) new Front-Upper Engine Support Cross-Member Bushings only (F7CZ-6A061-AA) by removing approximately 1/4″ (6 mm) of material from two (2) sides of the upper bushing. Use a utility knife or hack saw to achieve desired shape (Figure 2). b. Reinstall front attaching point of engine support cross-member with the original two (2) bolts, two (2) new Lower Bushings (F7CZ-6A061-BA), and two (2) new Upper Bushings (F7CZ-6A061-AA) that were modified in Step A (Figure 3). Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts. c. Reinstall rear attaching point of engine support cross-member using new Bushings (F7CZ-6A061-BA and F7CZ-6A061-AA) and original nuts (Figure 3). Both rear position upper bushings must be installed in “AS IS” condition (UNMODIFIED). d. Torque the retaining nuts and bolts to 64-89 N.m (47-65 lb-ft.). 11. Reinstall the front attaching points of the Belly Band with the original two (2) bolts. Apply 2-3 drops of threadlocker (EOAZ-19554-AA) to the bolts (Figure 1). 12. Reinstall rear-attaching points of the Belly Band with original two (2) nuts (Figure 1). 13. Torque the retaining nuts and bolts to 64-89 N-m (47-65 lb-ft.).

1998 Chrysler Town And Country LX SERPENTINE BELT SLIPS OFF IDLER PULLEY REPAIR PROCEDURE

0

Filed Under (Chrysler Manuals) by admin on 12-01-2012

download
REPAIR PROCEDURE This repair is compatible with DaimlerChrysler’s Mobile Service Program and does not require hoists or other full service facility special equipment. 1. Remove the serpentine belt from around the idler pulley by rotating the tensioner clockwise ( Fig. 3 ). 2. Remove the purge duty cycle solenoid and wiring harness from the right side engine mount. 3. Remove the two right side engine mount insulator vertical fasteners and loosen the horizontal fastener. DO NOT remove the large nut in the center of the core of the insulator ( Fig. 4 ). 4. Remove the load on the engine mount by carefully supporting the engine with a floor jack. 5. Remove the vertical and horizontal fasteners from the engine side bracket. Remove the engine mount assembly. 6. Remove the idler pulley from the engine mounting bracket. ( Fig. 3 ). 7. Remove the engine mounting bracket. 8. Install a new engine mounting bracket. Torque the fasteners to 40-68 N.m (30-50 ft-lbs.). 9. Install the idler pulley to the engine mounting bracket. Torque the fastener to 40-68 N.m (30-50 ft-lbs.). 10. Properly route and position a serpentine belt onto all pulleys except the idler pulley (Use a new belt if there is any evidence of damage to the original one). 11. Rotate the belt tensioner clockwise until the belt can be installed onto the idler pulley. Slowly release the belt tensioner. 12. Install the engine mount; torque the assembly in the following order, engine mount to rail fasteners 68 N.m (50 ft-lbs.), vertical fastener 102 N.m (75 ft-lbs.), and horizontal fastener 150 N.m (111 ft-lbs.). 13. Install the purge duty cycle solenoid to the engine mount. 14. Start the vehicle and let it run for one minute then turn the engine off. 15. Verify the serpentine belt is properly aligned ( Fig. 1 ) 16. If the serpentine belt has moved toward the outboard edge of the idler pulley, further diagnosis will be required. WARRANTY INFORMATION POLICY: Reimbursable within the provisions of the warranty. LABOR OPERATION NO: 07-20-20-96 TIME ALLOWANCE: 0.7 Hrs. FAILURE CODE: P8 – New Par

Related Content:

1998 chrysler town and country, free 1KD FACTORY ENGINE REPAIR MANUAL

Related Content:

2000 Nissan sentra 1 8 engine bolt torque diagram, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, 6m70 service manual obd codes pdf, 2005 chevy impala motor diagram, Position of sensors in mitsubishi 4m 51 engine, mitsubishi 4m51 engine wiring diagram, TOYOTA SO5D SERVICE MANUAL, perodua engine overhall pdf, 4EFE engine manual