Skip to content

99 grand prix transmission diagram

You search PDF repair manual about 99 grand prix transmission diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.

1999 Jeep Grand Cherokee Limited AUTOMATIC TRANSMISSIONS Chrysler 45RFE Electronic Controls Repair Manual

download
INTERNAL TCM Circuit Description The TCM is reporting internal errors. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Remove transmission control relay. Measure resistance between ground and relay ground circuit (Black/Yellow wire) in relay connector. If resistance is greater than 5 ohms, repair open circuit. If resistance s not greater than 5 ohms, go to next step. 2. The TCM has an internal problem and must be replaced. P0715: INPUT SPEED SENSOR ERROR Circuit Description DTC P0715 will set if an excessive change in input RPM has been detected in any gear. Possible Causes * Intermittent wiring and connector problems. * Faulty input speed sensor. * Input speed sensor circuits shorted to ground, shorted to voltage, or open. * Faulty TCM. Diagnostic Procedure 1. Place gear selector in “P” position and start engine. Using scan tool, monitor input speed sensor value. If value is less than 400 RPM, go to next step. If value is not less than 400 RPM, go to step 9. 2. Turn ignition switch to LOCK position. Install Transmission Simulator (8333). Turn ignition on. Using transmission simulator, turn rotary knob to middle (1000/3000) position. Turn INPUT/OUTPUT switch on. Using scan tool, monitor input and output speed sensor values. If input speed sensor value is 2950- 3050 RPM and output speed sensor value is 950-1050 RPM, replace input speed sensor. If speed sensor values are not as specified, go to next step. 3. Turn ignition switch to LOCK position. Disconnect TCM harness connector. Remove transmission control relay. Using fused jumper wire, jumper fused B+ circuit (Red/White wire) and transmission relay output circuit (Red wire) together at relay connector. Turn ignition on. Measure voltage between ground and input speed sensor signal circuit (Red/Black wire) at TCM harness connector. If voltage is greater than 3 volts, repair circuit for short to voltage. If voltage is not greater than 3 volts, remove jumper wire, install relay and go to next step. 4. Turn ignition switch to LOCK position. Disconnect input speed sensor harness connector. Measure resistance of input speed sensor signal circuit (Red/Black wire) between TCM and input speed sensor. If resistance is greater than 5 ohms, repair open circuit. If resistance is not greater than 5 ohms, go to next step. 5. Measure resistance of input speed sensor ground circuit (Dark Blue/Black wire) between TCM and input

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

1996 Pontiac Grand Am DTC P0502 Vehicle Speed Sensor (VSS) Circuit Low Input (3.1L VIN M) Service Manual

download
Action Taken When the DTC Sets Conditions for Clearing the MIL/DTC Diagnostic Aids Test Description The numbers below refer to the step numbers on the diagnostic table. 2. This step verifies that the PCM is receiving a signal from the vehicle speed sensor. 3. This step verifies that there are no opens in the circuitry from the vehicle speed sensor to the PCM connector. 7. This step performs a resistance test on the VSS circuits from the PCM connector. • The transmission defaults to 3rd gear. • The PCM inhibits TCC operation. • The PCM illuminates the Malfunction Indicator Lamp (MIL). • The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported. • A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. • The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. • Check for PRNDL DTC P0705. DTC P0705 affects transmission operation. This may set DTC P0502 falsely. • Check for Electromagnetic Interference (EMI) in circuits 400 and 401. EMI may be induced if the harness is routed along the spark plug wires. • Inspect the wiring for poor electrical connections at the PCM. Inspect the wiring at the TCC brake switch. Look for the following conditions: – A bent terminal – A backed out terminal – A damaged terminal – Poor terminal tension – A chafed wire – A broken wire inside the insulation • When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. • Ensure that the VSS is securely tightened to the case extension. DTC P0502 Vehicle Speed Sensor Circuit (VSS) Low Input