Skip to content

99 isuzu rodeo owners manual

You search PDF repair manual about 99 isuzu rodeo owners manual, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

1994 Chevy Truck C 1500 Truck 2WD Tune-up and Engine Performance Checks/ Ignition-Timing Connector Location Change Manual

download
SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1)

1981-1996 ISUZU Amigo/Pick-ups/Rodeo/Trooper Glow Plugs SYSTEM TESTING REMOVAL AND INSTALLATION MANUAL

download
SYSTEM TESTING See Figures 1, 2, 3 and 4 Fig. Fig. 1: Glow plug system schematic Fig. Fig. 2: Dropping resistor and glow plug relay locations Fig. Fig. 3: Thermo switch location Fig. Fig. 4: Dropping resistor check To test the dropping resistor, check for continuity across the terminals as described in the illustration. If no continuity exists, replace the unit. 1. To test the thermo switch, first remove the switch. Submerge the end of the switch in water and raise the temperature gradually. The switch should be off at 126-140°F (53-60°C) or lower. The switch should be on at 134-145°F (57-63°C) or higher. If not, replace the switch. 2. REMOVAL & INSTALLATION See Figure 5 Fig. Fig. 5: Location of the glow plugs The glow plugs are located under the injection nozzles, and are threaded into the cylinder head. Disconnect the negative (-) battery cable. 1. Disconnect the glow plug and unscrew it from the engine. 2. To install: Lubricate with anti-seize compound before installing the plug. 3. Install and tighten the plug to 65 ft. lbs. (88 Nm). 4. Reconnect the plug wiring. 5. Connect the battery cable and check operation. 6.

Chrysler 413-426 CH- 6 B CHRYSLER 6 -PACK INTAKE MANIFOLD INSTALLATION MANUAL

download
NOTE: Please refer to Edelbrock Performer Series Carburetor Owner’s Manual for detailed tuning procedures. 1. Due to design, the fuel/air mixture and cylinder charging are very efficient with the CH-6B intake manifold. Generally speaking, the stock jetting for the recommended aftermarket carburetors will not need changing. Specific applications may show an increase in performance through further tuning. 2. Aftermarket distributor curve kits may be used with this intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM. 4. The compression ratio should be at least 9.5 to 1 to work properly with Performer RPM camshafts. 5. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this occur, recalibrate with a richer jet INSTALLATION: 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Use a factory style valley pan along with the recommended gaskets. 4. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 5. Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs.