Skip to content

99 ranger 4 by 4 axel removal

You search PDF repair manual about 99 ranger 4 by 4 axel removal, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

1994 Ford Explorer SPINDLE AND SHAFT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

download
Removal 1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub. See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION. 2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if equipped) and splash shield. 3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 . 4. Remove left shaft assembly (if required). On all applications, wrap spindle in protective cloth and place second step of spindle in soft-jawed vise. 5. On Explorer and Ranger, remove oil seal using slide hammer and Seal Remover (TOOL-1175-AC). Remove needle bearing from spindle. Press seal from shaft assembly. See Fig. 9 . 6. On Bronco and F150, remove needle bearing and oil seal using slide hammer and Cup Puller (T77F- 1102-A). Press seal from shaft assembly. Installation 1. Clean all dirt and grease from spindle bearing bore. Ensure bearing bore is free of nicks and burrs. On Explorer and Ranger, install seal on shaft assembly using press and Seal Installer (T83T-3132-A). 2. On Bronco and F150, install seal on shaft assembly, with seal lip toward spindle. On right side applications, install rubber boot and NEW keystone clamps on stub shaft. Install right shaft assembly into stub shaft, with stub shaft missing spline aligned with shaft assembly. 3. Ensure splines are fully engaged. Install rubber boot over assembly and tighten keystone clamps. On left axle applications, install shaft assembly through steering knuckle, and engage in splines. 4. Install needle bearing in spindle, with manufacturer identification mark facing away from spindle bore. For bearing installation, use Handle (T80T-4000-W), and Bearing/Seal Installer (T83T-3123-A for Explorer and Ranger; T80T-4000-S for Bronco and F150).

1997 Mercedes Benz SL 500 Hydraulic Cylinder For Soft Top Bow Removal And Installation Manual

download
NOTE: It is necessary to plug the hydraulic lines immediately with plugs 129 589 91 07 and the connections with plugs 129 589 00 91 11. Hydraulic cylinder remove on main bracket from inside of vehicle and lay down in soft top compartment (fig. 8) Hydraulic lines on hydraulic cylinder remove (fig. 8) NOTE: Plug the hydraulic lines immediately with plugs 129 589 00 91 07, the connections on the distributors and hydraulic cylinders with plugs 129 589 00 91 11. Screws screw out (fig. 8, item 8) and remove limit switch (item 9) from hydraulic cylinder NOTE: Check limit switches after completing vehicle and adjust, if required. Reinstall in opposite order (observe installation note) Check for proper function and leakage Special too Installation note When installing the hydraulic cylinder pay attention to the code numbers on hydraulic lines as well as the position of the lines in the B-pillar. Line positioning and code numbers Removal & Installation of Hydraulic Cylinder For Top Actuation Notes Removal & Installation of Hydraulic Cylinder For Top Actuation Preliminary jobs: Remove coupe roof (operating instructions). Remove baggage shelf. See: Interior Moulding / Trim\Service and Repair Remove coverings in rear. Remove occasional seats. See: Seats\Service and Repair

TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION MANUAL

download
TIMING BELT REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE ENGINE UNDER COVER 3. REMOVE AIR CLEANER DUCT 4. REMOVE DRIVE BELT, FAN WITH FLUID COUPLING AND WATER PUMP PULLEY (See step 5 in water pump removal in Cooling System) 5. REMOVE RADIATOR ASSEMBLY (See steps 5 and 6 in radiator removal in Cooling System) 6. REMOVE NO.3 TIMING BELT COVER (a) Remove the oil filler cap. (b) Using a 5 mm hexagon wrench, remove the 6 bolts and belt cover. 7. REMOVE NO.2 TIMING BELT COVER Using a 5 mm hexagon wrench, remove the 3 bolts, belt cover and gasket. If you are unable to loosen the bolt on the right because the PS pump pulley interferes with the hexagon wrench, first remove the pulley as follows. (a) Using SST to hold the pulley, remove the nut. SST 09960-10010 (b) Remove the pulley. 8. REMOVE DRIVE BELT TENSIONER Remove the 3 bolts and tensioner. – ENGINE ENGINE MECHANICAL EG-19 9. SET NO.1 CYLINDER TO TDC/COMPRESSION (a) Turn the crankshaft pulley, and align its groove with timing mark “0″ of the No.1 timing belt cover. NOTICE: Always turn the crankshaft clockwise. (b) Check that the timing marks of the camshaft timing pulleys are aligned with the timing marks of the No.4 timing belt cover. If not, turn the crankshaft 1 revolution (360?). 10. REMOVE TIMING BELT FROM CAMSHAFT TIMING PULLEYS HINT (Re-using timing belt): Place matchmarks on the timing belt and camshaft timing pulleys as shown in the illustration. (a) Alternately loosen the 2 bolts, and remove them, the tensioner and dust boot. (b) Disconnect the timing belt from the camshaft timing pulleys. 11. REMOVE CAMSHAFT TIMING PULLEYS Using SST, remove the bolt for the timing pulley. Remove both timing pulleys. SST 09960-10010 (09962-01000, 09963-01000) 12. REMOVE CRANKSHAFT PULLEY (a) Using SST, loosen the pulley bolt. SST 09213-70010, 09330-00021 (b) Remove the SST and pulley bolt

1999 Dodge Intrepid PRIMARY TIMING CHAIN And SPROCKETS REMOVAL AND INSTALLATION MANUAL

download
Removal 1. Remove upper radiator crossmember. Disconnect fan assembly connector. Remove fan assembly. Remove drive belts. Using Crankshaft Pulley Holder (8191), hold crankshaft pulley and remove center bolt. Using a 3-jaw puller, remove crankshaft pulley. 2. Remove upper intake manifold. See INTAKE MANIFOLD . Remove electrical and vacuum harness retaining clips from valve cover studs. Remove ignition coils. Remove valve covers. Remove power steering pump and set aside. Remove drive belt tensioner pulley and bracket. Remove timing chain cover. 3. Align crankshaft sprocket timing mark to mark on oil pump housing. Mark on oil pump housing is 60 degrees ATDC of number one cylinder. See Fig. 10