Skip to content

ac actuator for 2003 gmc yukon xl

You search PDF repair manual about ac actuator for 2003 gmc yukon xl, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

2003 Mazda 6 V6-3.0L DOHC Airflow Mode Actuator Manual

download
AIRFLOW MODE ACTUATOR INSPECTION Full-auto Air Conditioner 1. Connect battery positive voltage to terminal E or F and ground to terminal F or E of the airflow mode actuator. 2. Verify that the airflow mode actuator operates as shown. * If not as specified, replace the airflow mode actuator 3. Verify that the resistance between the terminals of the airflow mode actuator is as shown in the graph. * If not as specified, replace the airflow mode actuator. Manual Air Conditioner Operating inspection 1. Turn the fan switch to OFF. 2. Turn the mode dial to VENT. 3. Turn the ignition switch to ON position, (engine ON) 4. Turn the fan switch 4th position. 5. Turn the mode dial from VENT to DEFROSTER. 6. Verify that the airflow mode actuator moves smoothly. * If not as specified, inspect the airflow mode main link and sub link for clogging and deformity. * If the actuator cannot move at all, go to voltage inspection. Voltage inspection 1. Disconnect the airflow mode actuator connector. 2. Turn the ignition switch to ON position, (engine OFF) Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 3. Verify that the voltage between the terminals of airflow mode actuator (harness-side) is as shown in the table. * If not as specified, perform the harness inspection and mode switch inspection. (See CLIMATE CONTROL UNIT INSPECTION, Manual Air Conditioner.) * If as specified, replace the airflow mode actuator

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

2003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 2003 F-Super Duty 250-550/Excursion Workshop Manual 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plat 2003 F-Super Duty 250-550/Excursion Workshop Manual 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed