Skip to content

adjusting throttle position sensor on 2004 kia sedona

You search PDF repair manual about adjusting throttle position sensor on 2004 kia sedona, if there are search results will appear below. If search results do not exist, please search by others keyword.

Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

1996 Ford Taurus Camshaft Position Sensor removal and installation manual

download
REMOVAL CAUTION: Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block INSTALLATION CAUTION : A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement CMP sensor. Failure to follow this procedure will result in improper sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. 1. Attach Syncro Positioning Tool T95T-12200-A as follows: a. Engage CMP sensor housing vane into the radial slot of the tool. b. Rotate tool on CMP sensor housing until tool boss engages notch in sensor housing. 2. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly. 3. Install sensor housing so that drive gear engagement occurs when arrow on ocator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate CMP sensor electrical connector in the pre-removal position. 4. Rotate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear. 5. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees. 6. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14- 22 lb ft)

2003-2004 Accord V6 MIL Comes On With DTC P2195 or P2197 REPAIR PROCEDURE

download
Before you update an ECM/PCM, make sure the battery in the vehicle is fully charged. •To prevent ECM/PCM damage, do not operate anything electrical (audio system, brakes, A/C, power windows, moonroof, etc.) during the update. 1. If not already done, load the May 2004 or later i N CD onto the i N master terminal. Loading instructions are included with the CD. 2. Update the ECM/PCM software with the HIM. For updating instructions, refer to Programming the HIM and Updating an ECM/PCM With a Programmed HIM in Service Bulletin 01-023, Updating Control Units/Modules . 3. Warm up the engine to operating temperature, then shut if off. 4. Do the ECM/PCM RESET and the CKP PATTERN CLEAR with the HDS. OP# Description FRTTemplate ID 123503Retrieve the DTC(s), and clear the codes with the HDS. 0.3 04-038A 125517Update the ECM/PCM software with the Honda Interface Module. 0.3 122505Do the CKP pattern learn. 0.32 of 2 04-038 5. Do the ECM/PCM idle learn procedure: •Make sure all electrical items (A/C, audio, rear window defogger, lights, etc.) are off. •Turn the ignition switch to the ON (II) position for 30 seconds. •Start the engine, and let it idle (throttle closed and all electrical items off) for 10 minutes. 6. Do the low-rpm CKP pattern learn: •Test-drive the vehicle on a level road: With the A/T in second gear, or the M/T in second or third gear, decelerate (with the throttle fully closed) from 2,500 rpm down to 1,000 rpm . •Stop the vehicle, and put the transmission into Park or Neutral. Set the parking brake. Do not turn off the ignition switch. 7. Connect the HDS to the DLC, and check the status of PULSER F/B LEARN: •On the Selection Menu , select PGM-FI . •On the Mode Menu , select Data List . •Check the value of PULSER F/B LEARN . •If the value is Completed , go to step 7. •If the value is Not Completed , be sure the engine is at normal operating temperature (the ECT SENSOR (1) value is 176 or higher), and return to step 5. 8. Do the high-rpm CKP pattern learn: NOTE: The low-rpm CKP pattern learn must be completed before you do the high-rpm CKP pattern learn. •Test-drive the vehicle on a level road: With the A/T in first gear, or the M/T in first gear, decelerate (with the throttle fully closed) from 5,000 rpm down to 3,000 rpm . •Stop the vehicle, and put the transmission into Park or Neutral. Set the parking brake. Do not turn off the ignition switch. 9. Connect the HDS to the DLC (if not already connected), and do this: •On the Selection Menu , select PGM-FI . •On the Mode Menu , select Data List . 10. Check the value of PULSER F/B LEARN (HIGH RPM) •If the value is Completed , you are finished. Disconnect the HDS. •If the value is Not Completed , be sure the engine is at normal operating temperature (the ECT SENSOR (1) value is 176 or higher), and repeat steps 5 thru 8

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models: