air brake repair manual

You search PDF repair manual about air brake repair manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  air brake repair manual Direct Download speed 5432 Kb/s

  air brake repair manual Full Version speed 8172 Kb/s



2004 Toyota Camry Disc Brake System Service/ Repair Manual

0

Filed Under (Toyota Manuals) by admin on 13-04-2012

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram

2002 Ford Truck Ranger Brakes – Rear Brakes Grabbing Condition Repair Manual

0

Filed Under (Ford Manuals) by admin on 24-04-2012

download
SERVICE PROCEDURE To service, reduce/minimize moisture intrusion into the rear drum brake assemblies by applying Motorcraft® Silicone Gasket and Sealant to the brake backing plate . WARNING Do not breathe dust or use compressed air to blow dust from storage containers or friction components. Remove dust using government-approved techniques. Friction component dust may be a cancer and lung disease hazard. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Exposure may also cause irritation to skin, eyes and respiratory tract, and may cause allergic reactions and/or may lead to other chronic health effects. If irritation persists, seek medical attention or advice. Failure to follow these instructions may result in serious personal injury. 1. Place vehicle on hoist and remove the rear wheels. 2. Remove the rear brake drums and replace the rear linings. Refer to Workshop Manual (WSM), Section 206-02. 3. Inspect the rear brake assemblies for damaged, missing and/or improperly seated adjuster plug or parking brake cable . 4. Inspect and clean the lining contact area of the brake drum ; machine if necessary. 5. Reinstall the rear brake drums and adjust the lining to drum clearance per WSM, Section 206-02. 6. Thoroughly clean the backside of the rear drum brake backing plate to promote proper adhesion of sealant. Zoom Sized for Print 7. Apply Motorcraft(R) Silicone Gasket and Sealant to the backside of the rear drum brake backing plate at the following inter[ace areas (Figure 1): ^Axle Flange ^ Wheel Cylinder ^ Parking Brake Cable ^Hold Down Pins 8. Reinstall the rear wheels and torque lug nuts per Workshop Manual, Section 204-04.

Related Content:

Motorcraft Service Owners Manual, 2002 ford ranger svc manual

1990 TOYOTA SUPRA REPAIR MANUAL DOWNLOAD

0

Filed Under (Toyota Manuals) by admin on 17-06-2011

download
INTRODUCTION MAINTENANCE ENGINE MECHANICAL wi EXHAUST SYSTEM TURBOCHARGER SYSTEM EMISSION CONTROL SYSTEMS EFI SYSTEM COOLING SYSTEM LUBRICATION SYSTEM IGNITION SYSTEM STARTING SYSTEM CHARGING SYSTEM CLUTCH MANUAL TRANSMISSION AUTOMATIC TRANSMISSION PROPELLER SHAFT FRONT AXLE AND SUSPENSION REAR AXLE AND SUSPENSION BRAKE SYSTEM STEERING SRS AIRBAG BODY ELECTRICAL SYSTEM BODY AIR CONDITIONING SYSTEM he procedures are presented in a step-by-step format: 0 The illustration shows what to do and where to do it. 0 The task heading tells what to do. 0 The detailed text tells how to perform the task and gives other information such as specifications and warnings. Example: , Task heading: what to do r’ 21. CHECK PISTON STROKE OF OVERDRIVE BRAKE (a) Place SST and a dial indicator onto the overdrive brake piston as shown in the figure. SST 09350-30020 (09350-06 1 20) Set pah No. Component part No. I I /’ Detailed text: how to do task I I (b) Measure the stroke applying and releasing the compressed air (4 – 8 kg/cm2, 57 – 114 psi or 392 – 785 kPa) as shown in the figure. Piston stroke: 1.40 – 1.70 mm (0.0551 – 0.0669 in.) Specification This format provides the experienced technician with a FAST TRACK to the information needed. The upper case task heading can be read at a glance when necessary, and the text below it provides detailed information. Important specifications and warnings always stand out in bold type. REFERENCES References have been kept to a minimum. However, when they are required you are given the page to refer to. SPECIFICATIONS Specifications are presented in bold type throughout the text where needed. You never have to leave the procedure to look up your specifications. They are also found in Appendex A, for quick reference. CAUTIONS, NOTICES, HINTS: CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other people. NOTICES are also presented in bold type, and indicate the possibility of damage to the components being repaired. HINTS are separated from the text but do not appear in bold. They provide additional information to help you efficiently perform the repair

Related Content:

2007 chevy uplander vtd wiring

2001 Dodge Dakota CENTRAL TIMER MODULE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Dodge Manuals) by admin on 28-06-2012

download
1. Connect scan tool to Data Link Connector (DLC), under lower left side of instrument panel. Turn ignition on. Using scan tool, attempt to communicate with Air Bag Control Module (ACM) and Controller Antilock Brake (CAB) module. If scan tool is able to identify or communicate with ACM and CAB, go to next step. If scan tool is not able to identify or communicate with ACM and/or CAB, perform appropriate DTC or symptom test. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION and SYMPTOM IDENTIFICATION tables under SELF-DIAGNOSTIC SYSTEM. 2. Turn ignition off. Disconnect Gray 26-pin Central Timer Module (CTM) connector C1. CTM is located behind left side kick panel. Ensure interior lights are off. Using DVOM, measure resistance between ground and Gray 26-pin CTM connector C1 terminals No. 1 and 16 (Black/Light Green wires) and No. 2 (Black wire). See Fig. 5 . If resistance is 10 ohms or less on each ground circuit, go to next step. If resistance is more than 10 ohms on any ground circuit, check for an open between appropriate CTM connector terminal and ground. See GROUND DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 3. Disconnect Gray 12-pin CTM connector C3. Using test light connected to ground, probe Gray 12-pin CTM connector C3 terminals No. 1 (Red/Tan wire) and No. 6 (Red/Light Green wire). See Fig. 8 . If test light illuminates on both circuits, go to next step. If test light does not illuminate on both circuits, check for open in appropriate circuit between power distribution center and CTM. See POWER DISTRIBUTION article in WIRING DIAGRAMS. Repair as necessary. 4. Turn ignition on. Using scan tool, ensure there is PCI BUS communication with other modules (besides the ACM and CAB). If scan tool is able to identify or communicate with all modules, go to next step. If scan tool is not able to identify or communicate with all modules, refer to appropriate communications symptom for diagnosis. See DIAGNOSTIC TROUBLE CODE IDENTIFICATION table under SELF-DIAGNOSTIC SYSTEM. 5. Connect Scope Input Cable (CH7058) to channel one connector on scan tool. Connect Cable-To-Probe Adapter (CH7062) and Black and Red test probes to scope input cable. Connect Black test probe to ground. Connect Red test probe to PCI BUS circuit at Gray 26-pin CTM connector C1 terminal No. 10 (Violet/Yellow wire). 6. Using scan tool, select PEP MODULE TOOLS, LAB SCOPE, LIVE DATA. Select 12 VOLT SQUARE WAVE. Press F2 for SCOPE. Press F2 and use DOWN arrow to set voltage scale to 20 volts. Press F2 again when complete. Turn ignition on. If reading on lab scope toggles between zero and 7.5 volts, go to next step. If reading on lab scope does not toggle between zero and 7.5 volts, repair open in PCI BUS circuit (Violet/Yellow wire). 7. Replace CTM. See CENTRAL TIMER MODULE under REMOVAL & INSTALLATION

Related Content:

2001 dodge ram central timer module location, can you repair a central timer unit?, 2000 mazda mpv p0755 code Broken wire, UT Scan Plan, scan tool will not communicate for air bag codes, programing a CTM, ct 20 turbo diagram, control time module rear bumper for 2002 dodge dakota, central timer module 2003 Dodge Dakota replacement, central time moduale dodge durango 2001

1997 Ford Explorer/ Mountaineer Intake Manifold Upper Repair Manual

0

Filed Under (Ford Manuals) by admin on 09-05-2012

download
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.

Related Content:

2000 mpv egr vacuum line, 1997 FORD EXPLORER VACUUM T SHAPPED HOSE, 2az fe intake manifold, 305 egr intke gasket, bad egr valve symptoms aveo chevrolet

Ford Sierra Service and Repair Manual Download

0

Filed Under (Ford Manuals) by admin on 20-05-2012

download
Puddles on the garage floor or drive, or obvious wetness under the bonnet or underneath the car, suggest a leak that needs investigating. It can sometimes be difficult to decide where the leak is coming from, especially if the engine bay is very dirty already. Leaking oil or fluid can also be blown rearwards by the passage of air under the car, giving a false impression of where the problem lies. Warning: Most automotive oils and fluids are poisonous. Wash them off skin, and change out of contaminated clothing, without delay. Identifying leaks The smell of a fluid leaking from the car may provide a clue to what’s leaking. Some fluids are distinctively coloured. It may help to clean the car carefully and to park it over some clean paper overnight as an aid to locating the source of the leak. Remember that some leaks may only occur while the engine is running. Sump oil Gearbox oil Brake fluid Power steering fluid Oil from filter Antifreeze Engine oil may leak from the drain plug… …or from the base of the oil filter. Leaking antifreeze often leaves a crystalline deposit like this. Gearbox oil can leak from the seals at the inboard ends of the driveshafts. A leak occurring at a wheel is almost certainly brake fluid. Power steering fluid may leak from the pipe connectors on the steering rack. 0•9 Roadside repairs When jump-starting a car using a booster battery, observe the following precautions: ? Before connecting the booster battery, make sure that the ignition is switched off. ? Ensure that all electrical equipment (lights, heater, wipers, etc) is switched off. ? Make sure that the booster battery is the same voltage as the discharged one in the vehicle. ? If the battery is being jump-started from the battery in another vehicle, the two vehcles MUST NOT TOUCH each other. ? Make sure that the transmission is in neutral (or PARK, in the case of automatic transmission). Jump starting will get you out of trouble, but you must correct whatever made the battery go flat in the first place. There are three possibilities: 1 The battery has been drained by repeated attempts to start, or by leaving the lights on. 2 The charging system is not working properly (alternator drivebelt slack or broken, alternator wiring fault or alternator itself faulty). 3 The battery itself is at fault (electrolyte low, or battery worn out). Connect one end of the red jump lead to the positive (+) terminal of the flat battery Connect the other end of the red lead to the positive (+) terminal of the booster battery. Connect one end of the black jump lead to the negative (-) terminal of the booster battery Connect the other end of the black jump lead to a bolt or bracket on the engine block, well away from the battery, on the vehicle to be started. 1 2 3 4 Make sure that the jump leads will not come into contact with the fan, drive- belts or other moving parts of the engine. 5 Start the engine using the booster battery, then with the engine running at idle speed, disconnect the jump leads in the reverse order of connection

Related Content:

2005 ford escape battery drain, ac leaking in chevy trailblazer, antifreeze for a 2013 chevy cruze, chevy cruze coolant leak

1992 Ford Taurus V6 Dashboard / Instrument Panel Service and Repair Removal and Installation

0

Filed Under (Ford Manuals) by admin on 08-06-2011

download
Removal and Installation 1. Position front wheels in the straight ahead position. 2. Disconnect positive battery cable. 3. Remove cluster finish panel, please refer to Body and Frame/Interior Trim/Dash Board/Service and Repair/ See 4. Disconnect all electrical connections from steering column switches. 5. Remove two bolts and reinforcement from under steering column. 6. Disengage insulator retainer and remove insulator. 7. Remove four nuts and absorber assembly from under steering column. CAUTION: Do not rotate steering column shaft. 8. Disconnect park brake release cable and wiring connector from park brake and ignition switch wiring connector. 9. Remove four nuts retaining steering column to support, disconnect PRNDL cable (column shift) and lower column on front seat. Cover front seat to protect from damage. 10. Install lock cylinder to ensure that steering column shaft does not turn. 11. Remove four retaining screws from cluster, disconnect wiring and remove. 12. Remove one bolt at steering column opening attaching instrument panel to brace 13. Remove one instrument panel brace retaining bolt (under the radio area). 14. Remove sound insulator under glove compartment by removing two pushnuts that secure insulator to studs on climate control case. 15. Remove three screws attaching glove compartment assembly to instrument panel and remove door assembly. 16. Remove air cleaner, battery and battery tray.

Related Content:

2008 ford taurus repair manual download, how to remove steeringwheel on 2003 taruas

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram