Skip to content

arvin meritor rear axle

You search PDF repair manual about arvin meritor rear axle, if there are search results will appear below. If search results do not exist, please search by others keyword.

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

2002 Ford Truck Ranger Brakes – Rear Brakes Grabbing Condition Repair Manual

download
SERVICE PROCEDURE To service, reduce/minimize moisture intrusion into the rear drum brake assemblies by applying Motorcraft® Silicone Gasket and Sealant to the brake backing plate . WARNING Do not breathe dust or use compressed air to blow dust from storage containers or friction components. Remove dust using government-approved techniques. Friction component dust may be a cancer and lung disease hazard. Exposure to potentially hazardous components may occur if dusts are created during repair of friction components, such as brake pads and clutch discs. Exposure may also cause irritation to skin, eyes and respiratory tract, and may cause allergic reactions and/or may lead to other chronic health effects. If irritation persists, seek medical attention or advice. Failure to follow these instructions may result in serious personal injury. 1. Place vehicle on hoist and remove the rear wheels. 2. Remove the rear brake drums and replace the rear linings. Refer to Workshop Manual (WSM), Section 206-02. 3. Inspect the rear brake assemblies for damaged, missing and/or improperly seated adjuster plug or parking brake cable . 4. Inspect and clean the lining contact area of the brake drum ; machine if necessary. 5. Reinstall the rear brake drums and adjust the lining to drum clearance per WSM, Section 206-02. 6. Thoroughly clean the backside of the rear drum brake backing plate to promote proper adhesion of sealant. Zoom Sized for Print 7. Apply Motorcraft(R) Silicone Gasket and Sealant to the backside of the rear drum brake backing plate at the following inter[ace areas (Figure 1): ^Axle Flange ^ Wheel Cylinder ^ Parking Brake Cable ^Hold Down Pins 8. Reinstall the rear wheels and torque lug nuts per Workshop Manual, Section 204-04.

Sidekick / Tracker Solid Axle Suspension 2 Door Installation Instructions

download
1. Lift vehicle and support by frame & remove wheels. 2. Remove rear portion of exhaust behind cat . 3. Drain transfer case, front and rear diffs. Remove front and rear driveshafts. Remove e-brake handle cover (console) & back-off tensioner. 4. Remove rear brake drums. Disconnect e-brake cables from arm & backing plates & remove rubber cable looms from control arm & frame. 5. Support rear housing. Disconnect lower control arms, upper A-arm, breather, brake hose and shocks from the chassis. 6. Support front A-arm. Remove three nuts from the top of the strut. 2 7. Disconnect sway bar from A-arms. Separate tie rod ends at the spindles. On drivers side, disconnect brake hose at the inner fender & remove clip at the frame. Remove 3 bolts from axle flange and the lower A-arm bolts. 8. On passenger side, disconnect brake hose at the frame. Remove A-arm bolts. The axle pulls straight out of the differential. 9. Remove sway bar from frame. Separate center link from pitman arm and unbolt idler arm from frame. 10. Remove front differential with its vent and rubber isolators. ** Use of the stock front and rear bumpers will cause serious tire clearance issues. We recommend Trail Tough bumpers and nerf bars. 11. Remove outer and inner rear bumpers. 12. Remove outer and inner front bumpers. Some trimming may be done to the ends of the grill. Removal of the grill may make this easier. 3 13. The second frame cross member from the front must be removed. In preparation, unclamp the fuel and brake lines from inside the right frame rail and tie them out of harms way (Towards the motor). 14. Using a sawzall, torch, plasma or cut-off disc, remove the second frame cross member (The one under the engine oil pan) completely. Be careful not to damage the frame rails. See next 2 photos below. 14. Continued 14. Continued 15. Removal of the front A-arm brackets (on the foreward most cross member) is optional. If you choose to remove them, be sure not to damage the cross member (shown NOT removed).

2003 Volvo S40 L4-1.9L Rear Brake Pads Removal And Installation Manual

download
the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective. NOTE: If the dirt guard is defective, dirt may have penetrated the cylinder. Therefore the brake caliper must be reconditioned. Checking the rear brake disc Check the brake disc surface. Check the lateral runout of the brake disc if the disc is uneven. Replace the brake disc if it is worn or grooved. NOTE: Minimum disc thickness = 8.4 mm . If installing new brake pads, the minimum disc thickness must be at least 8.9 mm . Checking the locating pins for the rear brake calipers Check the rubber sleeves on the locating pins. Replace if necessary. If necessary, lubricate the locating pins using Volvo silicon grease (P/N 1161325-4). Insert the locating pins in the rubber sleeves. The locating pins must slide into the sleeves easily. Rotating the brake piston backwards Block the brake caliper against the brake disc. Use special tool 999 5782. * Turn the plate (A) forward over the shaft and insert the tool * Install the lugs (B) in the cut-out in the brake piston * Turn the shaft (C) so that the plate (A) presses against the brake caliper * Turn the axle (D) to the right and press the piston back while turning the shaft (C) to the right so that the plate (A) is in contact with the brake caliper * Turn the brake piston back fully and remove the tool Install the wear indicator (A) on the under side of the inner installed brake pads. Install the brake pads. Position the brake caliper . Install the new locking bolt. Tighten to 33 Nm . Install the brake hose in the support. Install the retaining clip. NOTE: Secure adhesive foil onto the steel plates to prevent the rear brake pads from rattling. Installing the wheels Install wheels. Checking the brake fluid level WARNING: Always depress the brake pedal repeatedly before test driving the car. Check the brake fluid level