Skip to content

at oil temp light on 1992 toyota pick up

You search PDF repair manual about at oil temp light on 1992 toyota pick up, if there are search results will appear below. If search results do not exist, please search by others keyword.

TOYOTA DAYTIME RUNNING LIGHT DISABLING PROCEDUR / REPAIR MANUAL

download
Use the locking pick tool from the wire harness repair kit and back out the terminal from the appropriate connector for the DRL Relay or Body ECU. See the Reference Chart on Page 1 of this bulletin for pin and connector information. 3. Insulate the removed terminal using vinyl electrical tape. 4. Secure the wire and terminal to the outside of the wire harness using vinyl electrical tape. NOTE: For the 2000 MY Avalon, proceed to Step 5. For all remaining models, proceed to Step 6. 5. For 2000 model year Avalon: A. Order a new terminal with lead that is the same size and type as the terminal previously removed from the connector. (PN 82998-12690) B. Securely attach a 45 cm/ 18 in wire with an outside diameter of 2.0 mm or larger to the tail of the new terminal. Repair Procedure DRL Relay or Body ECU W/H Insulate Terminal Tape insulated terminal to outside of wire harness. P.N. 82998-12690
DAYTIME RUNNING LIGHT DISABLING PROCEDURE – EL011-00 October 6, 2000 Page 3 of 3 C. Securely attach an eyelet with a hole size of 7 mm to the end of the new wire. D. Insert the new terminal with lead into the Body ECU Connector B5, previously vacated by the original terminal. E. Properly attach and route the new wire to the exterior of the existing wire harness in a manner that will not allow it to become damaged or come into contact with any other circuits. F. Securely attach the eyelet to the existing ground point located in the left kick panel area. (Ground Point IF) 6. Check that the Daytime Running Light (DRL) operation has been disabled. 7. Reassemble any interior panels that were removed to gain access to components, connectors, etc.

TOYOTA 4RUNNER A750E (F) AUTOMATIC TRANSMISSION SERVICE MANUAL

download
The ATF level gauge (dip-stick) has been discontinued, and the ATF inspection method and the oil level inspection method have been changed. This mechanism consists of a refill plug, overflow plug, ATF temperature sensor No.2, and A/T OIL TEMP temperature warning light. ATF Filling procedures using SST (09843-18020): When a large amount of ATF needs to be filled (i.e. after removal and installation of oil pan or torque converter), perform the procedure from step 1. When the small amount of ATF is required (i.e. removal and installation of the oil cooler tube, repair of oil leak), perform the procedure from step 7. 1) Raise the vehicle keeping it level. 2) Remove the refill plug and overflow plug. 3) Fill ATF from the refill plug until it overflows from the overflow plug. 4) Install the overflow plug. 5) Fill the specified amount of ATF determined by procedure and install the refill plug. Example 6) Lower the vehicle down. 7) Use the SST (09843-18020) to short the terminals Tc and CG of the DLC3 connector: 8) Start the engine and allow it to idle. A/C switch must be turned OFF. 9) Move the shift lever slowly through each of the positions from the P to the L position, and move it back to the P position. 10) Move the shift lever from the D position, and quickly move then back and forth between N and D (once per less than 1.5 seconds) for at least 6 seconds. This will activate the oil temperature detection mode. Standard: The A/T OIL TEMP warning light remains illuminated for 2 seconds and it goes off. 11) Return the shift lever to the P position and disconnect the terminal Tc. 12) Idle the engine to raise the oil temperature. 13) Immediately after the ATF OIL TEMP warning light turns on, lift the vehicle up. The A/T OIL TEMP warning light will indicate the ATF temperature according to the following table. (Insert table here) 14) Remove the overflow plug and adjust oil quantity. If the ATF overflows, go to step 17, and if the ATF does not overflow, go to step 15. 15) Remove the refill plug. 16) Fill ATF to the refill plug until it flows out from the overflow plug. 17) When the ATF flow slows to a trickle, install the overflow plug. 18) Install the refill plug (only if the refill plug has been removed). 19) Lower the vehicle down. 20) Turn the ignition switch OFF to stop the engine. For details about the ATF Filling procedures, see the 2004 4Runner Repair Manual (Pub. No. RM1059U)

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

1992 Toyota Truck Pickup 2WD Cooling and Exhaust Engine Ignition Timing Adjustments Manual

download
1. Connect a tachometer test probe to terminal IG of the check connector, Fig. 211 2. NOTE: Never let the tachometer lead touch ground as this could cause damage to the igniter and/or coil. Be sure to check that your tachometer is compatible with this ignition system. Consult the operating manual for your instrument. Service Check Connector 3. Fig. 223 Ignition Timing (10) Check idle speed . 4. Idle Speed : 800 rpm Using a timing light, verify that the timing mark on the timing cover is aligned with the mark on the crankshaft pulley, Fig. 223 5. Ignition Timing: 10°BTDC at idle Tighten the distributor bolt and recheck the ignition timing. 6. Remove service wire. 7. Check idle advance timing with service wire removed. 8. Ignition Timing: 8°BTDC at idle Check idle speed and adjust if necessary, COMPUTERIZED ENGINE CONTROLS. 9. Disconnect tachometer and timing light from engine. 10. Timing Belt Removal Notes Fan Shroud Removal & Installation Remove radiator fan upper and lower shrouds. 1. Installing Power Steering Pump And Belt Remove power steering pump drive belt and pump. 2. Disconnect No. 2 and No. 3 air hoses from air pipe. 3. 4. Fan Removal Remove alternator drive belt , cooling fan, belt guide and fan pulley. 5. Remove No. 2 timing belt cover. 6. Fig. 6 Aligning Timing Marks Place No. 1 cylinder at TDC of compression stroke by turning the crankshaft pulley and aligning pulley groove with the “0” mark on the No. 1 timing belt cover. Ensure alignment marks on the camshaft timing sprockets and the No. 3 timing belt cover are correctly aligned, Fig. 6. 7. If not, turn the crankshaft pulley one complete revolution. 8. Crankshaft Pulley Removal

Installing the Cyron HT-1506 LED footwell light kit in a Toyota Prius

download
Begin by removing the lower glove compartment. Release the glove compartment latch, the squeeze both sides to release the catches and drop the box out of the dash. Disconnect the damper shock on the right hand side of the box by popping the shock arm from the plastic peg. Then press together on each side of the glove compartment and pull towards you. Remove the box and set it aside. Now, remove the silver passenger air vent to the left of the glove compartment. You can do this by grabbing it from the top and bottom and pulling straight back. Alternatively, you can curl your hand around inside the glove box opening and push the assembly out from the inside. It is helpful to push it from the inside to get it started and makes it easier to remove from the outside. Now is a good time to clean out the cabin air filter. It is located in the top part of the white box shown in the center of the above picture. If it’s really dirty it’s best to replace it. They are less than $20 at the dealer, or you can make your own from a household air conditioner filter. I like to vacuum mine every 4-6 months to keep it clean, and it will probably won’t need to be replaced for a long time.
Continue disassembly of the dash to allow for routing the power and signal wires. Plan your installation as far as the routing for Cyron controller and hub wiring. At this point, you must decide where to store the controller during normal use / driving. I chose to install my controller in the “secret drawer” on the lower front part of the center console, which means running wiring underneath the carpeting between the center console and the curved panel. The simpler option that requires less wire routing is to store it in the glove box. To remove the curved panel, begin by removing the plastic Christmas tree push pin from the passenger side of the curved panel. You can remove it with a flat screwdriver or gently pull the panel straight back and the pin will come loose. The driver’s side of the curved panel is held by a metal post with a plastic catch. Once the push pin is removed, pull the panel straight back and it will pop loose. The panel is fairly easy to remove and it will pop back in place on re-assembly. Once the curved panel is loose, remove the connector from the 12v accessory socket and set the panel aside. The connector is polarized so it will only fit the accessory socket in one orientation, so there is no need to mark it.
Remove the curved panel by gently pulling straight back. It will pop lose from the dash