audi a6 2001 front bumper removal instructions

You search PDF repair manual about audi a6 2001 front bumper removal instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  audi a6 2001 front bumper removal instructions Direct Download speed 5432 Kb/s

  audi a6 2001 front bumper removal instructions Full Version speed 8172 Kb/s



TOYOTA FJ CRUISER – FRONT BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 05-02-2011

download
Front Bumper Installation – TOYOTA FJ CRUISER Step 1 Very Important Before beginning installation, assure that vehicle has been pulled forward into work-area with the wheels straight and that the ground is level. The clearances around the FJ bumper are critical to proper installation and fitment. Moving vehicle with wheels turned causes slight frame twist preventing ease of removal of OE bumper and installation of new bumper without issue. Make sure you have plenty of room to work around front of vehicle. Open the hood at this time, you will need to see down through the inner-body core-support while removing your OE bumper and installing your Body Armor FJ Bumper. Step 2 a. Unpack bumper using staple puller to remove staples. Save all packing materials and take care not to tear cartons. b. Remove hardware and misc.parts. Check parts/hardware list to confirm all parts and necessary hardware are included. c. It’s a good idea to spray all OE attaching hardware at this time with penetrating oil before beginning removal of OE bumper. This will ease removal as well as to help assure that none of the bolts’ / nuts’ threads are damaged during removal. Use extra caution when working with the bumper mounting studs & nuts. Step 3Prep bumper for install: You may install your auxilary lights in the light pockets. The light tab is slotted to allow for adjustment for adjustment for light grilles. You may also attach a second set of lights on the top deck . Also attach the grill guard at this time. Step 4 a. Begin removing OE bumper following instructions and photos on the following page for detailed descriptions and references. When done, proceed to Step 4 here. Step 5 a. If equipped, remove OE chassis skid plate and set aside for install after new bumper is installed. Save OE hardware to re-install the skid plate once new bumper is installed (3 upper bolts and 2 lower bolts, lowers have spacers between frame & skid plate). b. Remove the (3) outer hold-down hex nuts holding bumper to frame-caps on both passenger and driver sides. Un-clip the outer ends of the bumper from the outer bumper support clips (see Photo 5 on following page) by pulling bumper fascia down and out of clip on driver and passenger sides. Next, while a helper holds the bumper in place, loosen and remove the inner hold-down hex nuts on both passenger and driver sides. Reference Photo 1 on the last page for stud locations. The bumper should now slide off the front of the locating / mounting studs in the frame-caps. Remove slowly prevent paint damage. Save hold-down nuts. c. Remove the outer bumper support clips from both driver and passenger sides (see Photo 5 on following page) Step 6 a. If you bought a winch, skip to Step 6b. If you did not purchase a winch, you can mount the winch cover plate / lower bumper fascia, and fairlead slot cover plate to the bumper now, using (6) 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer, and (1) hex nut on each bolt. See photos 4 & 5 on the last page for reference. b. If you purchased a winch for your FJ, now is the time to mount it in the bumper. The winch will bolt down using the fairlead mounting bracket and 10mm bolts to secure winch & fairlead bracket to bumper. The roller fairlead bolts to the fairlead bracket using the 1/2″ hex nuts supplied. See photo 3 on the last page for reference. Be sure to mount with the correct side of winch to passenger side for solenoid pack installation / clearance. Once the winch is bolted in, you can mount the winch cover plate / lower bumper fascia to the bottom of the bumper using (4) of the 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer and (1) hex nut on each bolt. If you purchased lights, mount them to the light tabs. It the lights have a protective grille you should be able. to use the cover. Important: Follow winch mfr’s directions for cable to winch / solenoid / battery connections. Use caution to assure clearance of any and all bumper / winch / mounting surfaces at all cable end connections. Coil cables and lay in winch mount plate to protect against damage while installing bumper onto vehicle. Place coiled cables in winch mount plate to assure no interference with the radiator, a/c line and / or inner body core support during bumper installation. Cables to be run in Step 7. Step 7 Along with your helper, one person on each side, guide your Body Armor FJ Bumper onto the the frame-cap mounting studs. Use caution guiding the bumper on slowly and evenly to prevent paint damage. Locating / mounting studs and bumper mounting plates can be seen down through inner-body core support while guiding bumper into place. Make sure the bumper does not contact grill or fascia while installing bumper as this can cause paint damage. While you or your helper hold the bumper in place, thread the OE hold-down nuts onto mounting studs to hold the bumper in place, hand tighten at this time. Step 8 Confirm bumper is even side-to-side, torque hold-down nuts to 80 ft.lbs. Again confirm bumper is even and there are no clearance issues between the bumper and any part of the body and / or inner-body core-support. You can now run the winch cables through the inner-body core support to the battery. If you purchased a set of lights to be used with your bumper, you can now wire them up, please follow the detailed light manufacturer instructions. **Body Armor is not responsible for any issues with respect to the wiring, operation or warranties to the lights Step 9 a. Fit the wheel well inner-liner end-caps to the bottom of the bumper at each corner and bolt up with supplied 1/4″ x .75″ phillips- head machine screws, (2) each side, into drilled / threaded holes in bottom corners of bumper. See photos 6 & 7 on the last page. b. Next, using the OE hardware and spacers, re-install your chassis skidplate, making sure it’s straight before tightening. c. Using the (2) remaining 1/4″ x .75″ phillips-head machine screws, mount your license plate to threaded holes in the bumper face. d. Re-install the grill by snapping onto clips and using the OE push-pins and screws to hold down in OE locations. ** trimming off the front inner fender is a customer option, it is not required. We recommend you check the torque of all bolts after about two weeks, and after every off-road / trail run thereafter to assure tightness

Related Content:

how to remove chevy sonic front bumper, INSTALLING A FRONT BUMPER ON THE TOYOTA RAV 4, replacing front bumper end cap on 2012 Toyota FJ cruiser, 2004fordf150frontbumperdiagram, 2000 4runner step bumper rear chrome install instructions, remove back bumper on kia sedona, remove 2006 toyota matrix rear bumper, remove back bumper on kia sedona cover, rear fender for 2008 camry, prius steering wheel pad removal instructions

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to change evaporator core on 1998 blazer, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, Ford Expedition heater core instructions, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, how replace alternator in 2006 honda odessey, toyota sienna grill removal, jaguar fuel hose removal, 4k carburetor manual, how to check windshield wiper motor and arm on a 2007 malibut, how to remove center console 2013 camry, toyota 4k carburetor service manual

TOYOTA AND LEXUS HIGHLANDER HYBRID REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-03-2012

download
Engine and Vehicle Identification Chart………………………………………..4-2 General Engine Specifications………4-2 Engine Tune-Up Specifications……..4-2 Capacities ………………………………….4-3 Valve Specifications …………………….4-3 Crankshaft and Connecting Rod Specifications……………………..4-3 Camshaft and Bearing Specifications ……………………………4-4 Piston and Ring Specifications……..4-4 Torque Specifications………………….4-4 Wheel Alignment ………………………..4-5 Tire, Wheel and Ball Joint Specifications ……………………………4-5 Brake Specifications ……………………4-5 Scheduled Maintenance Intervals……………………………………4-6 STEERING AND SUSPENSION ………………4-28 A Air Bag…………………………………….4-28 Disarming ……………………………4-28 Precautions ………………………….4-28 Alternator …………………………………..4-7 B Brake Caliper ……………………………4-30 Removal And Installation……….4-30 C Camshaft and Valve Lifters…………4-14 Inspection ……………………………4-16 Removal & Installation…………..4-14 CV-Joints………………………………… 4-24 Overhaul ……………………………..4-24 Cylinder Head …………………………..4-10 Removal & Installation…………..4-10 D Disc Brake Pads………………………..4-32 Removal And Installation……….4-32 E Engine Assembly ………………………..4-7 Removal & Installation…………….4-7 Exhaust Manifold ………………………4-12 Removal & Installation…………..4-12 F Front Crankshaft Seal………………..4-14 Removal & Installation…………..4-14 Front Halfshaft………………………….4-23 Removal & Installation…………..4-23 Front Strut ……………………………….4-28 Removal & Installation…………..4-28 Front Wheel Bearing………………….4-29 Fuel Filter ………………………………..4-21 Fuel Injector……………………………..4-22 Removal & Installation…………..4-22 Fuel Pump ……………………………….4-21 Removal & Installation…………..4-21 Fuel System Pressure………………..4-21 Relieving ……………………………..4-21 H Heater Core………………………………..4-7 Removal & Installation…………….4-7 Hybrid Transaxle Assembly…………4-22 Removal & Installation…………..4-22 I Ignition Timing ………………………….. 4-7 Adjustment…………………………….4-7 Intake Manifold …………………………4-11 Removal & Installation…………..4-11 L Lower Ball Joint………………………..4-29 Removal & Installation…………..4-29 Lower Control Arm……………………4-29 Removal & Installation…………..4-29 O Oil Pan…………………………………….4-18 Removal & Installation…………..4-18 Oil Pump …………………………………4-18 Removal & Installation…………..4-18 P Pinion Seal ………………………………4-27 Removal & Installation…………..4-27 Piston and Ring………………………..4-21 Positioning ………………………….4-21 Power Rack And Pinion Steering Gear…………………………..4-28 Removal & Installation…………..4-28 R Rear Halfshaft………………………….. 4-24 Removal And Installation……….4-24 Rear Main Seal…………………………4-19 Removal & Installation…………..4-19 Rear Strut…………………………………4-28 Conventional Strut Overhaul…..4-28 Removal And Installation……….4-28 Rear Traction Motor…………………..4-22 Removal & Installation…………..4-22 Rear Wheel Bearing…………………..4-29 Removal And Installation……….4-29 T Timing Belt ………………………………4-19 Removal & Installation…………..4-19 V Valve Lash ……………………………….4-17 Adjustment…………………………..4-17 W Water Pump ……………………………..4-10 Removal & Installation………..

Related Content:

how to install running boards on honda pilot, nissan ka20 16 valve cyl head gasket replacement, 2001 chevrolet monte carlo radiator removal, zx2 vct replacement instructions, 2006 sienna liftgate struts replacement video, 2002 highlander brake torque, nissan ka20 timing marks, replace alternator on honda ridgeline, quicksilver isolators pdf, whats the piece that connects to lower control arm on 1997 Buick le sabre

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

2007 TOYOTA FJ CRUISER HEAVY DUTY WINCH BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
INSTALLATION 1. Remove the screws from the rear corners of the bumper, two in each side. Figure 2 Figure 2 Bumper mounting screws, left side 2. Remove the eight screws along the bottom of the bumper. Figure 3 Figure 3 Lower bumper mounting screws Remove 2 screws in rear of bumper Remove 8 screws in bottom of bumper (4 per side) WARN INDUSTRIES PAGE 4 73465 A0 3. Lift the hood and remove the two screws from the top of the grille. Retain the hardware for use later. Figure 4 Figure 4 Grille fasteners 4. Remove the two plastic fasteners from the top of the grille. Retain the hardware for use later. Carefully pry the center pins up before removing the fasteners. Figure 5 Figure 5 Left grille fastener removal 5. Pull the grille free of the retaining clips with a “sharp” pull. Remove 2 screws Remove 2 plastic fasteners (1each side) Lift center pin then pry fastener out WARN INDUSTRIES PAGE 5 73465 A0 6. Remove five plastic fasteners from the top of the bumper. Two are behind the upper bumper support. Figure 6 Figure 6 Bumper fasteners 7. Pull the bumper corners free by pulling the ends rearward and out. The top of the bumper is snapped into plastic clips just below the fender corners, in front of the flares. Pull the bumper free. Figure 7 Figure 7 Left bumper end removal Remove 5 plastic fasteners (2 behind bumper not shown) WARN INDUSTRIES PAGE 6 73465 A0 8. Remove the two screws that hold each plastic mounting block in place and remove the blocks. Figure 8 Figure 8 LH bumper mounting block 9. Remove the three screws and remove the upper bumper support. Figure 9 Figure 9 Upper bumper support Remove 2 screws and remove plastic block Remove 3 screws Do not remove the nuts on top Bumper mounting block Upper bumper support WARN INDUSTRIES PAGE 7 73465 A0 10. Remove the 8 hex flange nuts and remove the bumper beam. Retain the hardware for bumper installation. Figure 10 Figure 10 Bumper beam, left side shown 11. Remove the four screws and remove the skid pan. Retain the hardware for reinstallation of the skid pan. Figure 11 Figure 11 Skid pan 12. Remove the molded plastic inner fender extensions by clipping or drilling out the rivets holding them to the bottom of the inner fenders. Figure 12 Remove 4 fasteners to remove skid pan Remove 4 flange nuts per side Bumper beam WARN INDUSTRIES PAGE 8 73465 A0 Figure 12 Left side fender extension 12. Locate the 1″ hole in the side of the frame behind the body mount. Drill a 1/2″ hole through the center into the inner wall. The Spacer Tube may be used as a centering tool. Repeat for opposite side. Figure 13 Figure 13 Outside left frame rail 13. Hold the Lower Frame Bracket in position and insert a 12mm bolt with 1/2″ lock washer and flat washer through the bottom hole in the Bracket and into the threaded hole in the frame. Do not tighten yet. Figure 14 Drill ½” hole through center of existing hole into inner frame wall Clip or drill rivets to remove fender extension Fender extension WARN INDUSTRIES PAGE 9 73465 A0 14. Slide a 1/2″ flat washer and Spacer Tube over a 1/2 x 4″ bolt and insert through the Lower Frame Bracket and Frame. Install 1/2″ lock washer and hex nut. Do not tighten yet. Figure 14 15. Slide an Upper Frame Bracket above the frame rail along the inside of the Lower Frame Bracket. Align the holes and insert two 7/16 x 1 1/2″ bolts through the holes and install a lock washer and hex nut on each. Do not tighten yet.

Related Content:

how to remove 03 sequoia rere bumper, fj cruiser front bumper removal, romoving rear bumper on mazda 6, removed 2012 mazda 3 bumper, remove rear bumper 2005 camry, remove lower bumper r350, removal of rear bumper 2003 ford explorer, removal of fj cruiser lower grill, rear bumper of 07 corolla removal, plasitic piece under carraige nissal altima

1996 Nissan Altima GLE TIMING CHAIN REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Nissan Manuals) by admin on 24-02-2011

download
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables. 2. Remove front exhaust tube. Remove intake manifold collector supports, and intake manifold. Remove exhaust manifold with catalytic converter. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. Remove injectors and fuel rail as an assembly. Remove distributor cap and spark plugs. 3. Set cylinder No. 1 at TDC of compression stroke, ensuring marks on crankshaft pulley and front cover align, and distributor rotor points to spark plug wire No. 1 on cap. Remove cylinder head cover. Remove distributor. 4. Prevent camshafts from turning, and remove camshaft sprocket bolts. Remove camshaft sprocket. See Fig. 13 . Mark and remove camshaft bearing caps in reverse order of installation. See Fig. 16 . Remove camshafts. 5. Loosen cylinder head bolts in 2 or 3 steps, in reverse order of tightening sequence. See Fig. 11 . Remove camshaft sprocket cover. Remove outer (upper) chain tensioner and guide. Remove outer timing chain. Remove idler sprocket bolt. Remove cylinder head. 6. Remove oil pan and oil strainer. See OIL PAN. Remove accessory drive belts. Remove A/C compressor idler pulley (if equipped). Remove crankshaft pulley. Remove front cover. Remove chain tensioner, tensioner arm and chain guides. Remove inner (lower) timing chain and idler sprocket. Remove oil pump drive spacer and crankshaft sprocket. Inspection 1. Inspect chain roller links. Replace chain if roller links are cracked or worn. Inspect cylinder head and cylinder block mating surfaces for warpage. If warpage exceeds specification, machine cylinder head. See CYLINDER HEAD under ENGINE SPECIFICATIONS. 2. If machining reduces cylinder head height to less than specification, replace cylinder head. After machining, rotate camshaft by hand. Replace cylinder head if camshaft does not rotate freely.

Related Content:

1997 altima cam timing, cummins n14 cylinder heads, 03 2az-fe head dowel pins, how to disable child licks on 2013 GMC terrain, how to install cylinder head on c-15cat engine, how to replace cilinder head in1 8 toyota, how to top overhaul peugeot 206, is timing set on compresson stroke 2000 2 0 vw beetle, procedure on removal fo cv axle in 2005 volvo s40 2 4i, removing ih1066 cylinder liners

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, how to replace wheel bearings on a 08 silverodo, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, snap ring assemble, Need to torque specifications 1999 GMC 1500 wheel hub bearings, 1977 ford f-350 rear wheel diagram, 2009 impala hub mounting bolt torque, removing rear wheel bearing race on 06 ford f-250, removing wheel bearing off a 2009 ford ranger rear axle

1995-1999 TOYOTA TACOMA BODY LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 21-10-2011

download
1. Read all warnings and instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part’s list and the picture diagrams). NOTE: This kit is designed to fit Tacoma models only, 95 1/2 -97 models equipped with air conditions will require modification to the low pressure A/C line at the firewall. It will need to be bent or in some cases the line may need to be lengthened. The vehicle will need to be taken to a certified A/C service technician to have the system evacuated. The line can then be lengthened between four and five inches. It is crucial that the procedure is done properly to avoid damage to the A/C system. If at anytime during the installation you encounter something different from what is outlined in the instructions, call technical support. (928) 636-7080. www.PerformanceAccessories.com . 2. Park the vehicle on a clean, dry, flat, level surface. Block the tires so the vehicle cannot roll in either direction. WARNING The Supplemental Restraint System (SRS, or air bag) must be deactivated during lift kit installation to avoid accidental air bag deployment while working near SRS sensors and wiring. Do not allow anyone near the air bag during lift kit installation. Accidental deployment can result in serious personal injury or death. Refer to your factory service manual/owner’s manual for the recommended procedure to disable the SRS. The SRS must be reactivated before driving the vehicle. 3. Disconnect both battery cables. Be sure to disconnect the negative cable first, then the positive cable. Remove the airbag fuse from the fuse box. 4. Remove the wire loom that runs from under the alternator to the battery from the mounting brackets. One bracket is on top of the frame. The other bracket is on the fender well. The plastic mounting-collar will slide off the bracket by pushing on the tab on the collar. 5. Remove the fuse that controls the air bag system from the fuse box (refer to the owners manual for the exact location). 6. Remove the ground wire that runs from the back of the engine to the top of the firewall. Remove the wire loom from the mounting bracket on the firewall. Remove the bracket from the firewall. Turn the bracket upside down. Insert the mounting bolt through the ground wire removed from the firewall, Then through the bracket. Tighten securely. Reinstall the bolt that mounted the ground wire to the firewall. Tighten the bolt securely. Do not attach the wire loom at this time. 7. Gently pull out the plastic clips that mount the front fender well skirts to the frame. NOTE: Be very careful with the plastic clips. They will break easily. 8. 4 wheel drive models only. Remove the front axle vent hose from the mounting bracket on the driver’s side fender well. The hose should remain in the frame bracket. 9. Remove the vacuum hose from the bracket that holds it to the drivers side fenderwell. This should allow enough slack to not damage the hose during lifting. 10. Remove the front bumper. Remove the light bulbs and wires from the light housings on each side of the bumper. There are two holes in the fender wells to access the outside bumper mounting bolts. Remove the nuts that mount the outside of the bumper to the body. Remove the bolts that mount the bumper to each side of the frame. Remove the bumper from the vehicle. 11. Remove the grill assembly. Remove the turn signal housing from the body. Disconnect the wiring attached to the housing. The grill is mounted to plastic tabs that have a lever in the middle. This lever is locked into place when the grill is mounted. To remove the grill, unlock the tabs and slide the grill off. Be sure that all of the mounting tabs are released before attempting to remove the grill

Related Content:

2002 leganza cmp pins, brakes for 97 636 pettibone, fuse layout 1999 tacoma, leveling kit tacoma 1999, om 636 repair manual, reinstall a grill on a 2009 toyota tacoma, srs electrical connector for 2008 toyota tacoma

1999 Ford Windstar Instrument Panel and Console REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals, Uncategorized) by admin on 23-04-2012

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Remove the steering wheel. Refer to Section 211-04 . 2. Remove the passenger side air bag module. Refer to Section 501-20B . 3. Disconnect the antenna in-line connector. 4. Remove the RH instrument panel reinforcement bolt. 5. Close the glove compartment. 6. Remove the utility compartment. 1. Remove the four two part pin type retainers. 2. Remove the utility compartment. * Disconnect the power point electrical connector. 7. If equipped, disconnect the compact disc changer electrical connector. 8. Release the compact disc changer electrical connector locator. 9. Remove the LH and RH scuff plates. 10. Remove the LH and RH A-pillar lower trim panels. 11. Position the LH and RH front door weatherstrip seals aside. 12. Remove the RH ground bolts. 13. If equipped, remove LH and RH instrument panel lower insulators. 14. Remove the instrument panel lower steering column opening cover. 1. Remove the screws. 2. Remove the instrument panel lower steering column opening cover. 15. Remove the instrument panel opening cover reinforcement. 1. Remove the bolts. 2. Remove the instrument panel opening cover reinforcement. 16. Disconnect the LH wiring harness electrical connectors. 17. Disconnect the electronic crash sensor (ECS) electrical connector. 1. Release the locking clip. 2. Disconnect the ECS electrical connector 18. Disconnect the automatic transmission shift cable. 1. Disconnect the cable from the steering column shift tube lever. 2. Disconnect the cable from the steering column bracket. 19. Separate the intermediate shaft from the steering column. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column. 20. Disconnect the climate control harness electrical connector. 21. Disconnect the climate control vacuum harness connector. 22. Disconnect the fuse junction panel electrical connectors. 23. Remove the LH instrument panel reinforcement bol 4. Remove the four instrument panel center support bolts. 25. Remove the instrument panel defroster opening grille. * If equipped, disconnect the sunload sensor electrical connector. 26. Remove the cowl top bolts. 27. Remove the RH cowl side bolts. 28. Remove the LH cowl side bolts. 29. NOTE: Two technicians are required to carry out this step. Remove the instrument panel. Installation CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. NOTE: Two technicians are required to carry out this step

Related Content:

2000 Isuzu 5 7 NPR Repair Manual lower intake manifold, charging system on 1999 isuzu npr not charging gas engine, ford five hundred instrument panel, remove ac panel from ford five hundred

Related Content:

how to remove chevy sonic front bumper, INSTALLING A FRONT BUMPER ON THE TOYOTA RAV 4, replacing front bumper end cap on 2012 Toyota FJ cruiser, 2004fordf150frontbumperdiagram, 2000 4runner step bumper rear chrome install instructions, remove back bumper on kia sedona, remove 2006 toyota matrix rear bumper, remove back bumper on kia sedona cover, rear fender for 2008 camry, prius steering wheel pad removal instructions