ball joint manual

You search PDF repair manual about ball joint manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ball joint manual Direct Download speed 5432 Kb/s

  ball joint manual Full Version speed 8172 Kb/s



1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 13-06-2012

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, how to replace rear upper arm kia sedona, torqe for ball joint 2001 prizm, oem ball joint press, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, 08 silverado lower ball joint removal

2008 Honda Accord L4-2.4L Knuckle/ Hub Bearing Unit Replacement

0

Filed Under (Honda Manuals) by admin on 19-11-2011

download
Hub Bearing Unit Replacement 1. Raise the rear of the vehicle, and support it with safety stands in the proper locations. 2. Remove the wheel nuts, and the rear wheel. 3. Remove the brake hose mounting bolt (A). 4. Remove the brake caliper bracket mounting bolts (B), then remove the caliper assembly (C) from the knuckle. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper assembly from the undercarriage. Do not twist the brake hose excessively. 5. Remove the two washers (A). NOTE: During installation, make sure the washers are installed between the brake caliper bracket and the knuckle. 6. Remove the rear brake disc. 7. Remove the hub bearing unit (A) and O-ring (B). 8. Check the hub bearing unit for damage and cracks. 9. Install the hub bearing unit in the reverse order of removal, and note these items: * Use a new O-ring on reassembly. * After installing the brake caliper, make sure the clearance between lower arm B and the parking brake cable is more than 5 mm (3/16 in.). * Before installing the brake disc, clean the mating surfaces of the hub bearing unit and the brake disc. * Before installing the wheel, clean the mating surfaces of the brake disc and the inside of the wheel. * Check the wheel alignment, and adjust it if necessary. Knuckle Replacement 1. Remove the hub bearing unit. 2. Remove the splash guard (A). 3. Remove the lock pin (A) from the upper arm ball joint, then remove the castle nut (B). NOTE: During installation, install the lock pin as shown after tightening the new nut. 4. Disconnect the upper arm ball joint from the knuckle using the ball joint remover. NOTE: * Be careful not to damage the ball joint boot when installing the remover. * During installation, to connect the ball joint, raise the suspension with a jack. 5. Remove the wheel speed sensor (A) from the knuckle. Do not disconnect the wheel speed sensor connector. 6. Remove the self-locking nut (A) while holding the joint pin (B) with a hex wrench (C), then disconnect the stabilizer link (D) from the knuckle, and remove the brake hose bracket (E). NOTE: Use a new self-locking nut during reassembly. 7. Remove the damper lower mounting bolt (F). NOTE: Use a new mounting bolt during reassembly. 8. Remove the control arm mounting self-locking nut (A) and washer (B). NOTE: Use a new self-locking nut during reassembly 9. Remove the lower arm mounting bolt (A), and the lower arm B mounting bolt (B), then remove the knuckle (C). NOTE: Use new mounting bolts during reassembly. 10. Install the knuckle in the reverse order of removal, and note these items: * First install all the components, and lightly tighten the bolts and nuts, then raise the suspension to load it with the vehicle’s weight before fully tightening to the specified torque values. * Be careful not to damage the ball joint boot when connecting the knuckle. * Before connecting the ball joint, degrease the threaded section and tapered portion of the ball joint pin, the ball joint connecting hole, and the threaded section and mating surface of the castle nut.

Related Content:

2008 F250 STEERING GEAR PITMAN ARM NUT SIZE, bearing retaining nut for a 2004 Trailblazer, brake caliper dust boot honda 2007 accord coupe

Coil Spring Spacer Installation Instructions

0

Filed Under (More Manuals) by admin on 24-12-2011

download
1. Check to see that the spacer kit you purchased matches the year and model of your vehicle. Spacer kits two inches or taller may require a spring compressor to install. Ball joint and tie rod forks may also be useful. 2. A good portion of your front suspension will be disassembled so this would be a good time to replace any worn parts (i.e. tie rod ends, ball joints, idler arm and any bushings) Replace bushings with polyurethane replacement parts. 3. Jack up vehicle as high as possible using jack stands for support at all times. 4. With vehicle safely off the ground remove front tires. It is advisable to disassemble on side at a time so that you can use the other side as a reference for re-assembly in the event you get side tracked. 5. Remove the brake caliper from the rotor (attached with 2 bolts inside the caliper or with press-in clips depending on the vehicle). Do not remove the brake line from the caliper unless you intend to bleed the brakes at this time. Set the caliper aside or tie it up to the frame rail. Avoid pinching the brake line. 6. Remove the tie rod from the spindle using the proper tools. Do not hit the tie rod itself or the nut on the threaded portion of the tie rod or it may cause damaged and need replacing. 7. Remove the anti-sway bar from the lower control arm. This would be a good time to replace the end link bushings with polyurethane replacement bushings. 8. If your vehicle is equipped with anti-lock brakes you must now disconnect the front rotor sensor from the dust shield or spindle and set it aside. 9. Disconnect your shock absorber completely from the vehicle whether it is mounted inside the coil spring or not. 10. Support the lower control arm with jack just touching the arm. This will prevent it from dropping when the ball joint is disconnected. 11. The use of a coil spring compressor is recommended before the following steps are taken. 12. Disconnect the upper ball joint from the top of the spindle using the proper tools. Do not hit the ball joint or the threaded end of the ball joint. Once the ball joint is free the spindle should move easily. 13. Be careful when lowering the lower control arm. The coil spring is under high compression and may shoot out when released. Do not stand near the side of the truck during this step. Lower the jack so that the lower control arm swings down. If the coil spring has not fallen out on it’s own you may need to use a pry bar from the front of the vehicle to remove it. 14. Note which end of the coil spring is “bottom” for installation. Also note the depression in the lower control arm. It is important that the last winding of the coil spring fit into the indentation completely so that the vehicle will sit level. Do not switch coil springs from side to side as some vehicles have a specific “right” and “left” coil spring. 15. Check the coil spacer for proper fitment into the coil spring mount in the frame. The flat part of the spacer should face up and touch the top of the spring mount. Some vehicles have guiding tabs to center the coil spring in its top mount. These tabs may have become bent and need to be bent back to allow the spacer to properly fit in the mount. 16. Install the coil spring with the spacer on top of it. If used the coil spring compressor should still be on the spring in a compressed state. If it is not you may need to compress the spring before re-installing. Make sure the spacer is centered in the upper mount and the bottom of the spring is properly nested in the receptor groove on the lower control arm. If you are installing a two-inch or taller spacer you may need a spring compressor. Follow all safety rules when installing the coil spring as it will be under extreme compression. 17. Raise the lower control arm with a jack once the coil spring and spacer are properly lined up. Raise until the spindle is high enough to bolt on the upper ball joint. Before bolting on the upper ball joint make sure the brake caliper and brake line are where they need to be since some brake lines run inside the spindle and outside the coil spring. 18. With the upper ball joint tight and a cotter pin re-installed you may now remove the jack from under the lower control arm. 19. Assemble all of the components previously removed (sway bar with new polyurethane bushings, tie rod ends with polyurethane grease boot, brake caliper and anti-lock sensor). Don’t forget the shock with a new colored boot while it is off. 20. Repeat instructions for other side. 21. After properly installing both spacers you can install your front tires and lower vehicle back to the ground. 22. Your vehicle may sit too high at first because the suspension needs to settle. Carefully back the vehicle up and drive forward a few times using the brakes frequently. Park on level ground and check out your lift. 23. The vehicle will now require a front wheel alignment. Failure to do so may result in severe wear on your tires and may pull to one direction

Related Content:

1997 ford ranger coil spring spacer installation, 4L60E 3 4 Accumulator Assembly, how to replace rear coil spring on a buick rendezours, how to use evertough coil spring compressor, Jeep TJ coil spring perch, labor to replace control arms g6, metal clip on ow beam 2009 mazda 6, ranger coil spring replace, replace 2006 Impala control arm bushings, replacing rear springs for 2004 toyota sienna

Ball Joint Spacers for IFS Suspension

0

Filed Under (More Manuals) by admin on 20-12-2011

download
1) Block rear wheels, place front end of truck on jack stands supported on the frame and remove the front wheels. 2) Remove the original upper ball joint hardware. 3) Knock the studs out of the ball joint with a small hammer. This is done most easily if the joint is pressed against the arm supported with a floor jack. 4) Remove the factory shock. 5) Trim the lip. An angle grinder with a cut-off wheel or a small reciprocating saw works well. Trim enough to allow installation of the spacer. 6) Put the spacer in place, NOTCH FACING DOWNWARD and, using a floor jack to control arm height, align the ball joint and install the hardware. The notch acts as a weep hole to let any water that gets in from above drain out to prevent the ball joint from rusting out. 7) Tighten ball joint hardware using the provided nylon lock nuts. 8) Install new extended length shock. 9) Repeat for other side. 10) Re-install the wheels. 11) If the end of the upper control arm is too close to the tire at this point, there are a few options: • You can replace your wheels with a higher off-set. • You can add a 1/4″ wheel spacer to move the wheel/tire away from the suspension. 12) Put the vehicle back on the ground. 13) For low profile bump stops only: • Shim them approx. 1/2″ with some washers or use stock bump stops. • Failure to do so could result in damage to CV joints, shocks, or other components 14) Even with stock bump stops, you may experience some CV axle binding. • To check, let the suspension hang’ at full droop. • Rotate each CV axle shaft by hand and check for any binding at the CV joints. • If felt, several options to fix it are available: o Add some shims for the low profile bump stops. o Or install a front differential drop kit to lower the differential and thus lessen the CV joint angles.

Toyota Front Coil Spring Spacer Lift Kit Installation Manual

0

Filed Under (Toyota Manuals) by admin on 22-12-2011

download
INSTALLATION INSTRUCTIONS FRONT 1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, ball joint separator, jack stands, bench vise, and metric hand tools. 2. Jack the vehicle in the center of the front cross member. 3. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the ground. 4. Remove the front tires/wheels. 5. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut. 6. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool, be careful NOT to damage the ball joint boot) 7. Remove upper strut tower nuts holding strut assembly to strut tower (3) on each side of vehicle. 8. Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle. (Note the direction of the bolt for reinstallation) 9. Compress the coil spring on the strut assembly with a suitable coil spring compressor so that the coil spring has about 3/8″ play in the strut and remove the upper strut isolator mount nut. 10. Remove the coil spring isolator from the upper strut mounting plate. 11. Replace the upper strut mounting plate studs with the supplied studs with a bench vise and a deep well socket. (3 on each side) 12. Reinstall the factory coil spring isolator to the upper strut mounting plate. 13. Reinstall the compressed coil spring onto the strut assembly and reattach the upper strut mount plate using the stock hardware. See diagram. Torque upper strut mounting plate nut to 18 foot-pounds. 14. Decompress the coil spring in the strut assembly. Make sure that the spring is seated correctly into the strut assembly alignment indentation at the bottom of the strut and the top isolator. 15. Slide the coil spring spacer onto the top of the strut assembly over the 10mm studs. 16. Install the strut assembly into the strut tower and start the upper three 10mm lock nuts. (Make sure that the bottom of the strut is aligned as well) 17. Install the lower strut bolt in the original position and torque to 100 foot- pounds. (Step 8) 18. Using the floor jack, raise the lower control arm and connect the upper ball joint on the upper control arm to the spindle. Torque nut to 80 ft lbs. and make sure that you replace the cotter pin. (Not supplied) 19. Install the front tires/wheels. 20. Lower the vehicle onto the ground and tighten the upper strut tower 10mm nuts. Torque to 35 foot-pounds. (3 on each side) 21. RETORQUE ALL BOLTS AFTER 500 MILES.

Related Content:

what checks would you carry out before and after fitting a macpherson strut, sienna manual powered struts open manually, how man ft lbs for cadilla dts strut, how to replace upper strut mounts on a 2002 buick, how to replace front strut assembly 06 dakota, how to install lift support struts on 2006 Toyota Sienna, How to install lift gate struts, how to change out hatch struts on a toyota sienna, honda pilot strut replacement, Front strut replacement 1997 Ford Thunderbird

Toyota IFS Ball Joint Spacer Installation

0

Filed Under (Toyota Manuals) by admin on 04-11-2011

download
Ball Joint Spacer Installation Put the spacer in place, NOTCH FACING DOWNWARD and, using a floor jack to control arm height, align the ball joint and install the hardware. The notch acts as a weep hole to let any water that gets in from above drain out to prevent the ball joint from rusting out. Tighten ball joint hardware to 25 ft.lb. or 35 N.m. Note: Apply this torque to the allen head bolt and the Grade 10.9 nut only, then install the 2nd nylon lock nut and tighten it down snugly in order to lock the first nut in place. No need to toque the nylon lock nut to 25 ft.lb. value, it may strip. If you wish, you can spray the exposed head and threads of the bolts with some paint, as the black oxide coated hardware may tend to rust over time. Extend the shock to see if it needs shimming. (it likely will) Place the appropriate number of washers to ensure the shock does not limit down travel. Tighten shock hardware. Repeat for other side. Re-install the wheels. If the end of the upper control arm is too close to the tire at this point, there are several options: You can try and grind off part of the outer lip of the control arm (area at the left edge of the red circle in the photo above) You can add a 1/4″ wheel spacer to move the wheel/tire away from the suspension. You can swap to a narrower tire, for example changing from a 33×12.50 to a 33×10.50 tire will move the inner edge of the tire away from the control arm since it’ll have less sidewall bulge on the same wheel. You can swap to a wheel with less back side spacing, for example going from a 4.75″ to a 4.5″ backspaced wheel will move the inner edge of the wheel and tire 1/4″ away from the control arm (stock wheels are ~4.75″ backspacing). Put the vehicle back on the ground. For low profile bump stops only: Shim them approx. 1/2″ with some washers or use stock bump stops. Failure to do so could result in damage to CV joints, shocks, or other components

2007-2009 Chevy GM Truck 6-LUG Models Installation Instructions

0

Filed Under (Chevy Manuals) by admin on 24-12-2011

download
1. Place the vehicle on a flat surface and using a floor jack and jack stands lift the front of the vehicle by the frame so the wheels are off the ground. 2. Remove the front wheel on the driver-side of the vehicle. 3. Remove the sway bar end link. 4. Loosen the three upper strut mounting nuts, but DO NOT REMOVE them. 5. Locate the ABS line and unhook it from the upper control arm. 6. Remove the two lower strut mounting bolts. 7. Loosen the nuts on the upper ball joint, but DO NOT REMOVE them. Note: A hammer may be needed to break the ball joint free. 8. Now remove the ball joint nut, the three upper mounting nuts and remove the strut from the vehicle. 9. With the strut removed from the vehicle, place the leveling spacer on top of the strut assembly, then reinstall the strut assembly in the stock location with the new nuts provided in the kit. 10. Reinstall the upper ball joint nut and sway bar end link. Note: It may be necessary to use a pry bar to aid installation of the strut assembly. It may also be necessary to use a floor jack to raise the lower A-arm to get the ball joint nut installed. 11. Verify that all fasteners have been torqued to factory specs. 12. Reinstall the wheel, and torque to OEM specs. 13. Repeat the above steps on the passenger-side of the vehicle. 14. Adjust your headlights and get the vehicle aligned by a Certified Alignment Technician that is experienced with lifted vehicles. PROFESSIONAL INSTALLATION BY A CERTIFIED MECHANIC IS RECOMMENDED

Related Content:

Ball Joint Torque Specifications Guide, sway bar end link torque

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques, how many foot lbs torque on lower control arm bolt lincoln ls, ford e450 wheel torque, ford 4 0 sohc oil pan inserts torque specs

2007-Up Toyota Tundra 2WD/4WD ADJUSTABLE UPPER STRUT FRONT LIFT/ LEVELING KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Step 1: Measure current front ride height. Take a measurement from the bottom of the wheel/rim to the lip of the fender on each side of the vehicle. Write down measurements to help in determining ride height after new kit is installed. (Figure A) Step 2: Position vehicle on a flat surface or automotive lift. Suspend front wheels , lifting by the frame with a floor jack or lift jack. Secure using jack stands and wheel chocks. Be sure engine is turned OFF and vehicle is in PARK. Remove tire/wheel assembly on ONE side of vehicle . Step 3: Support Spindle to protect ABS system and brake lines! LOOSEN, but don’t completely remove upper ball joint nut, outer tie rod nut and sway bar link nut at the lower control arm. Step 4 : Break Outer tie rod and ball joint from their tapers using tools specific to this procedure. CAREFULLY, while supporting the spindle assembly, completely remove upper ball joint nut & tie rod nut, leaving the loosened sway bar link nut in place. ( Figure B) Step 5: Remove strut assembly from the vehicle. Remove LOWER strut bolt first, followed by the three (3) upper strut nuts. CAUTION! BE EXTREMELY CAREFULL TO SUPPORT STRUT ASSEMBLY WHEN REMOVING UPPER STRUT NUTS! The Strut/Spring assembly is heavy and can cause injury to technician or damage to other components if released too quickly! (Figure C) Step 6: Apply 50% of the INCLUDED Synthetic Grease to the TOP of the THREADED INNER ADJUSTMENT SCREW, as illustrated. (Figure D) Step 7: Using the original OEM stud nuts , secure new Adjustable Upper Strut Kit to OEM upper strut studs and torque to manufacturer’s specifications. (Figure E) IMPORTANT! Be sure the Threaded Adjustment Screw Rotates FREELY after securing kit to OEM top of strut! If not, slightly loosen the three upper stud nuts and reposition Threaded Adjuster Screw UPWARD slightly. Retorque upper stud nuts to manufacturer’s specifications and recheck that Inner Adjuster Screw rotates freely. Step 8: Install the Top Connection Plate ONLY, studs directed UPWARD, into position in the strut tower, and secure with the NEW Nylock stud nuts supplied with this kit. Torque stud nuts to OEM specifications. (Figure F) Step 9: Reinstall strut assembly . Be sure the new Adjustable Upper Strut Kit is THREADED DOWN in the MOST COMPACT POSITION for easiest reassembly, then pass exposed threaded area of the kit THROUGH the center of the Top Connection Plate already installed. HINT: The use of a pry bar or breaker bar may simplify reinstallation of the Strut Assembly. (Figure G) Step 10: Install Large 1-1/4-12 Adjustment Locking Jam Nut included with this kit and tighten until snug to Top Connection Plate. Install Snap Ring included with kit.

2006-2009 Dodge Ram 1500 4×4 Installation Instructions

0

Filed Under (Dodge Manuals) by admin on 22-12-2011

download
2006-2009 Dodge Ram 1500 4×4 1. Jack the truck up and support with jack stands. 2. Remove the wheels 3. Remove the sway bar link from below the control arm, remove the tie rod end, and the upper ball joint. 4. Remove the strut 5. Install the leveling kit on the strut 6. Reinstall the strut into the truck 8. Re-attach the tie rod end before the upper ball joint. 9. Using a floor jack, apply pressure to the lower ball joint and reattach the upper ball joint Align and adjust headlights

Related Content:

instructions todissassemble hvac from dash omn 2009 dodge ram, remove strut how to remove radio from 2006 dodge ram

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, how to replace rear upper arm kia sedona, torqe for ball joint 2001 prizm, oem ball joint press, peugeot 306 front lower arm removal, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000, 08 silverado lower ball joint removal