Skip to content

battery drain pontiac bonneville

You search PDF repair manual about battery drain pontiac bonneville, if there are search results will appear below. If search results do not exist, please search by others keyword.

Battery Electrical Drain/ Parasitic Load Test Repair Manual

download
1. Disconnect the battery negative cable 2. Install the male end of the J 38758 to the negative battery terminal. 3. Turn OFF the test switch. 4. Install the negative battery cable to the female end of the test switch. 5. Install the Scan Tool (or equivalent) or wait for 20 minutes. 6. Turn ON the test switch. 7. Road test the vehicle while activating all accessories, including the radio and the air conditioning. 8. Lower the door glass, then exit the vehicle. Do not move the door handle after closing the door. 9. Open the hood. Important The power down timer will reset to 20 minutes if any wake up inputs are received by a Class 2 device (after the scan tool has put all Class 2 devices to sleep). 10. Put all of the Class 2 devices into the sleep mode. 11. Turn OFF the ignition switch. Remove the key. Important From this point on, electrical continuity must be maintained in the ground circuit of the battery through the Test Switch J 38758 in the ON position or through the ammeter J 39200 . 12. Components such as PCM, VCM, Automatic Air Conditioning, and the Truck Body Control Module have timers that draw several amps of current while they cycle down. This can give a false parasitic drain reading. Wait 20 minutes for these components to power down before continuing this test (or use the scan tool to put all Class 2 devices to sleep). 13. Connect a jumper wire with a 10 A fuse J 36169-A to the terminals of the test switch. 14. Turn the test switch to the OFF position. 15. Wait ten seconds. If the fuse does not blow, the current is less than 10 A. The ammeter can be used safely. 16. Before the fused jumper wire is removed, turn the test switch to the ON position. Important If an ammeter other than the J 39200 is used, ensure that the vehicle does not have a high current drain that would damage the ammeter when connected to the circuit. 17. Perform the following procedure in order to detect a high current drain: A. Set the ammeter J 39200 to the 10 A scale. B. Connect the ammeter to the test switch terminals. C. Turn OFF the test switch. This allows the current to flow through the ammeter. D. Wait one minute, then inspect the current reading. Ñ When there is a current reading of 2 A or less, turn ON the test switch, this maintains continuity in the electrical system. Ñ Then, switch the meter down to the 2 A scale, for a more accurate reading, when the test switch is reopened. E. Open the test switch. F. Take the reading in milliamps. G. Note the battery reserve capacity. Refer to Battery Usage . Ñ Divide this number by 4. Example: 90/4 = 22.5 Ñ Compare this to the ammeter reading. Ñ The current drain in milliamps should not exceed this number. Ñ Example: if a battery has a reserve capacity of 90 minutes, the current drain should not exceed 22 milliamps. H. When the current draw is too high, remove the electrical system fuses one at a time until the draw returns to a value less than or equal to specifications. Ñ Start with the fuses that are hot all the time. Ñ To remove the fuse, you must first open the door, which causes a high enough current flow to damage the ammeter. Ñ Protect the ammeter, without disturbing the electrical continuity, by turning ON the test tool before opening the door. Ñ Remove the courtesy lamp fuse. Ñ Note the ammeter reading. Ñ If the parasitic load is still excessive, start removing the remaining fuses one at a time. Ñ Keep the courtesy lamp fuse out during diagnosis, so the door can remain open. Ñ Perform Steps 11 through 13 each time a fuse is removed. I. Removing the PCM or VCM fuse should cause a drop of less than 10 milliamps. A drop greater than 10 milliamps indicates a possible short to ground. J. Check the orange wires along with the components connected to the orange wires. No drop in the milliampere reading indicates the PCM or VCM is not drawing current. K. Repeat the parasitic current drain test procedure after any repair has been completed. L. When the cause of the excessive current draw has been located and repaired, remove the ammeter and the parasitic draw test switch.

Battery Electrical Drain/ Parasitic Load Test

download
1. Disconnect the battery negative cable. 2. Install the male end of the J 38758 to the negative battery terminal. 3. Turn OFF the test switch. 4. Install the negative battery cable to the female end of the test switch. 5. Install the Scan Tool (or equivalent) or wait for 20 minutes. 6. Turn ON the test switch. 7. Road test the vehicle while activating all accessories, including the radio and the air conditioning. 8. Lower the door glass, then exit the vehicle. Do not move the door handle after closing the door. 9. Open the hood. Important The power down timer will reset to 20 minutes if any wake up inputs are received by a Class 2 device (after the scan tool has put all Class 2 devices to sleep). 10. Put all of the Class 2 devices into the sleep mode. 11. Turn OFF the ignition switch. Remove the key. Important From this point on, electrical continuity must be maintained in the ground circuit of the battery through the Test Switch J 38758 in the ON position or through the ammeter J 39200 . 12. Components such as PCM, VCM, Automatic Air Conditioning, and the Truck Body Control Module have timers that draw several amps of current while they cycle down. This can give a false parasitic drain reading. Wait 20 minutes for these components to power down before continuing this test (or use the scan tool to put all Class 2 devices to sleep). 13. Connect a jumper wire with a 10 A fuse J 36169-A to the terminals of the test switch. 14. Turn the test switch to the OFF position. 15. Wait ten seconds. If the fuse does not blow, the current is less than 10 A. The ammeter can be used safely. 16. Before the fused jumper wire is removed, turn the test switch to the ON position. Important

2001 Pontiac Sunfire L4-2.2L VIN 4 Cylinder Head Removal And Installation Manual

download
Cylinder Head Replacement * Tools Required * J28467-360 Engine Support Fixture * J36660-A Torque Angle Meter. Removal Procedure 1. Disconnect the negative battery cable. 2. Relieve the fuel system pressure. 3. Drain cooling system . 4. Remove the alternative fuel module assembly. Remove the drive belt . 5. Remove the air cleaner outlet duct and resonator assembly. 6. Support engine using floor jack and block of wood. 7. Remove the engine mount . 3. Remove the intake manifold . 9. Remove the exhaust manifold 10. Disconnect the Engine Coolant Temperature Sensor ( ECT ) electrical connection. 11. Remove the valve rocker arm cover. Important: When removing valve train components keep them in order. Do this to ensure that the components are installed in the same locations and with the same mating surfaces as when removed. 12. Remove the rocker arms and pushrods. 13. Remove the generator. 14. Remove the generator rear brace. 15. Remove the power steering pump. Position the pump aside with the lines attached. 16. Remove the radiator inlet pipe. 17. Remove the ignition coil assembly. 18. Remove the accessory bracket. 19. Disconnect the secondary ignition wires from the spark plugs . 20. Remove the cylinder head bolts. 21. Remove the cylinder head. 22. Clean the following components: * Head gasket surface * Valve rocker arm cover gasket surface * Threads Installation Procedure Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin Important: Install the cylinder head gasket with the words THIS SIDE UP showing. Do not use sealer on the gasket. 1. Install the cylinder head gasket to the block. 2. Use a socket in order to push the cylinder head gasket over the rear dowel pin

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Diagnostic Information for Intermittent Vehicle No Crank/ Dead Battery

download
Diagnostic Information for Intermittent Vehicle No Crank/Dead Battery – (Feb 5, 2004) When diagnosing a concern regarding an intermittent vehicle no crank or dead battery, technicians should remove and reinstall the ignition switch using the Ignition Switch Replacement procedure in the Steering Wheel and Column section of SI. The ignition switch may have been misindexed in the steering column during a previous replacement . If the ignition switch is misindexed in one direction, the ignition switch circuits will not be completely open when the ignition switch is in the OFF position with the key removed. This may result in lights remaining on or instrument panel lights illuminating, which will drain the battery. If the ignition switch is misindexed in the opposite direction, the ignition circuits will open correctly but the ignition switch may not close the crank circuit properly when the ignition key is turned to the crank position. This will result in a no crank concern.