bleeding brakes buick park avenue ultra

You search PDF repair manual about bleeding brakes buick park avenue ultra, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bleeding brakes buick park avenue ultra Direct Download speed 5432 Kb/s

  bleeding brakes buick park avenue ultra Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, 99 buick park ave radiator installation, Rav 4 steering rack dismantle and refit procedure, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle

2000 Chrysler Town Ans Country Limited BLEEDING BRAKE SYSTEM

0

Filed Under (Chrysler Manuals) by admin on 15-06-2011

download
MANUAL BLEEDING 1. Fill master cylinder. Install clear vinyl bleed hose onto left rear bleed screw. Place other end of hose in clean transparent container. 2. Partially fill a container with clean brake fluid. Submerge end of hose in fluid. Pump pedal 3-4 times and hold. Open bleed screw at least one turn. 3. Close bleed screw. Release pedal. Repeat procedure until flow of brake fluid is clear and free of bubbles. Proceed to next bleed screw of brake bleeding sequence. See BLEEDING SEQUENCE table. BLEEDING SEQUENCE PRESSURE BLEEDING Ensure pressure bleeding equipment reservoir is kept at proper level during bleeding. Follow proper bleeding sequence. See BLEEDING SEQUENCE table. Follow equipment manufacturer’s instructions for bleeding. DO NOT exceed manufacturer’s recommended pressure specifications for bleeding. Ensure master cylinder reservoir is full when finished bleeding 1. Ensure all hydraulic brake system components are properly installed and all connections are tight. Using scan tool, check Controller Anti-Lock Brake (CAB) for faults. If any faults are stored, clear CAB faults. 2. Bleed base brake system. See MANUAL BLEEDING or PRESSURE BLEEDING . After bleeding base brake system, using scan tool, select ANTILOCK BRAKES followed by MISCELLANEOUS, then BLEED BRAKES. Follow scan tool screen prompts. When scan tool displays TEST COMPLETED, disconnect scan tool. Bleed base brake system again. Top off brake fluid reservoir and verify proper brake operation before moving vehicle.

Related Content:

02 buick century overheating and top radiator hose is hot bottom hose cold, how to put radiator support in 2013 chevy cruze, how to properly bleed cooling system 1997 chevy lumina, how to bleed my 2005 by, how to bleed brakes chrysler town and country, how to bleed 2001 durango radiator, how to bled chevy monte carlo 2004, cooling system on 1999 saturn sl1, bleeding the air from 05 monte carlo cooling system, avaitor 2005 overheats

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, 2005 buick century code p0455, hunter 9700 user manual, 2000 buick lesabre custom manual, how to change the lower control arms on a 2005 Titan pdf, hunter lift L401, integrated wheel end FOR F150, location of fuses and relays 2003 buick park avenue, Rear Tire wear Mecury Mariner, repair manual on 2001 cadi deville on motor mount

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 saturn sl1 owners manual, 2000 buick century service manual free, 560sl repair 1988, 2000 buick lesabre service manual pdf, 2000 buick lesabre repair manual free pdf download, diagrama buick century 2002 pmc, Diagram of us system old mobile intrigue, park avenue ac control schematic

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Related Content:

4t65e documentation pdf

1994 Cadillac DeVille Concours Procedure to Disable Illumination of Service Indicator AFTER the Installation of Passive Struts/Shocks

0

Filed Under (Cadillac Manuals) by admin on 11-06-2011

download
Run a wire from a switched ignition (hot in Run) source to relay pin 85. 1992-1993 Oldsmobile Achieva with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1992-1994 Buick Skylark with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1993-1996 Buick Park Avenue with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1991-1995 Oldsmobile Ninety Eight with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1994-1999 Pontiac Bonneville with Computer Command Ride (CCR) The feedback strut/shock assemblies are still available for these vehicles. However, if the customer desires to reduce the repair expense, the following steps may be taken to allow installation of non-feedback assemblies and the disabling of the malfunction indicator lamps. This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. Parts Information The following parts are required to make the correction on the 1993 Eldorado/Seville and the 1994-1995 DeVille. Parts are currently available from GMSPO

Related Content:

1993 cadallic deveal service manuel, 1992 park avenue repair manual, 1993 cadillac deville no pressure, 1994 buick century repair manual pdf, 1999 buick park avenue repair manual free pdf, buick park avenue 1992 repair manual, fix ac in 1995 sudan deville, program vin to computer 1999 cadillac deville, where is the vats computer on a 1994 cadillac deville

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 2007 kia rio service manual, 200lolds aleroraditor system, schematic for front brakes on 2005 Buick Rendezvous, 4t65e service manual online, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, pontiac 2007 g6 remove radiator cover

ALL INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 23-04-2012

download
SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. Groan noise during stopping: • Usually caused by glazing of the rotor’s surface as a result of heavy or frequent braking. • Refer to technical bulletins specific to the model of vehicle regarding this issue. • Replace the brake pads, then resurface the rotors and finish them with sand paper. Refer to Brake Service on page 5 for additional detail. Single clunk noise from front suspension when applying the brakes: • The noise is a result of the brake pads shifting in the direction of rotor rotation when the brakes are applied. Can be duplicated by lightly touching the brake pedal. • • If the brake pedal is pushed hard, the noise is less likely to occur. Make sure the brake pads and pad hardware (shims, springs, clips, etc) are installed correctly. Refer to ASIST for vehicle specific brake service information. Refer to Brake Service on page 5 for additional detail. Mull e he engine is started: • st er models, the self check occurs the first aches 5 mph after the engine is started. ors or drums. • WARNING: Brake dust may be hazardous if inhaled. Refer to the Service Manual (ESM) for brake • n and lubrication of brake pads, CAUTION: Do not get grease on the brake pad friction surface. A • Brake Judder is caused by rotor thickness variation and/or rotor run out.

Related Content:

manual for 1993 bmw 325i, Free 98 Honda Accord service Repair Manual, titan 5500 generator manual, lexus engine 2gr-fe chirping squeak noise sb0010-09, free 06 tacoms service repair manual, 2012 f-150 service manual, 94 nissan pickup diagnose repair, h22a service manual, Motorcraft Service Manual Download, motorcraftservice com

1999 GMC Truck Yukon PRNDL Display Inaccurate or Inoperative PRNDL Inaccurate Repair Manual

0

Filed Under (GMC Manuals) by admin on 15-02-2012

download
Did you perform the Instrument Cluster System Check? — Go to Step 2 Go to Instrument Cluster System Check 2 1. Disconnect the Transmission Range (TR) Switch connector C2. 2. Turn the ignition switch to the RUN position. 3. Conduct the PRNDL Logic Input Test by connecting fused jumper wires between ground and the appointed cavities of the TR Switch connector. Refer to PRNDL Logic Input Test PRNDL Logic Input Test . 4. Repeat for each transmission range. Do all ranges illuminate? — Go to Step 3 Go to Step 4 3 Adjust the transmission range switch. Refer to Park/Neutral Position Switch Adjustment (4L60E); Park/Neutral Position Switch Adjustment (4L80E) Automatic Transmissions. Replace the PNP Switch. Refer to Park/Neutral Position Switch Replacement (4L60E); Park/Neutral Position Switch Replacement (4L80E) in Automatic Transmissions. Is the repair complete? — Go to Instrument Cluster System Check — 4 1. Remove the I/P Cluster. 2. Connect a J 39200 DMM (continuity) between the I/P Cluster connector and connector C2 of the TR Switch to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 6 Go to Step 5 5 Locate and repair the open in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 6 Connect a J 39200 DMM (continuity) between the I/P Cluster connector and ground to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 7 Go to Step 8 Locate and repair the short to ground in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring 7 Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 8 Replace the I/P Cluster. Refer to Instrument Panel Cluster (IPC) Replacement . Is the repair complete?

Related Content:

07tahoe dashboard repair kit, 1996 buick instrument cluster problems, 1999 yukon radiator removal instructions, GM IPC CIRCUIT BOARDS

1997 Buick Century Limited 3.1/ 3.4L COLD ENGINE TICK OR RATTLE AFTER START-UP (REPLACE PISTON/ PIN ASSEMBLY)

0

Filed Under (Buick Manuals) by admin on 03-01-2012

download
Some customers may comment on a ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. CAUSE Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur. This level of noise does not affect the reliability or durability of the product. CORRECTION If piston-to-pin noise is detected and the customer desires the condition to be corrected, replace all six pistons with pin assemblies. The new piston sets have a minimal piston-to-pin clearance. Remember, piston-to-pin noise occurs in both park and drive at engine idle rpm and it varies in intensity depending on the number of pistons involved. A ticking sound means one piston is affected whereas a rattle or diesel type sound indicates more than one piston affected. The following should also be checked: 1. On W-Cars, make sure the right side engine splash shield is not contacting the engine crankshaft balancer. This condition usually happens cold and is caused by the shield curling when cold. 2. Reference Service Bulletin 57-71-06 for transmission rattle noise often confused for engine rattle noise. 3. Reference Service Bulletin 47-61-36 for Accessory Drive Belt Tensioner noise. 4. Check cylinder bore diameter and piston diameter as outlined in the Service Manual. Use the procedure in the appropriate Service Manual for piston replacement. Service Bulletin 57-61-24 (Section 6 – Engine). NOTE: Excessive cylinder bore to piston diameter clearance can cause a similar type noise. NOTE: When installing the new piston and pin assembly onto the existing rods, use extreme care to avoid damage to either the pin or piston bore. If damage to these areas occurs, the noise will return because the damage will cause wear and excessive clearance

Related Content:

toe reference diameter, 07 FUSO P0560, 08 escalade esv lifter noise, 1999 Buick Century rattleing noise, 2000 buick park ave making ratting car makes rattling, gm 3800 noises, popping niose front on 1997 buick lesabra, what could cause a ticking in an 1993 buick regal engine

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, 99 buick park ave radiator installation, Rav 4 steering rack dismantle and refit procedure, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle