bravada front axle shaft removal

You search PDF repair manual about bravada front axle shaft removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  bravada front axle shaft removal Direct Download speed 5432 Kb/s

  bravada front axle shaft removal Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, remove front diff bearing in navagator, remove rear axle on a 02 mustang, 2006 gmc envoy cv drive axles, remove right side axle on a 2001 toyota sienna, 2005 ford explorer rear axle nut size

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

1994 Nissan Maxima SE FWD Axle Shafts Removal And Installation Manual

0

Filed Under (Nissan Manuals) by admin on 21-05-2011

download
FWD AXLE SHAFT Removal 1. Raise and support vehicle. Remove wheel. Remove wheel bearing lock nut from end of drive axle. Remove disc brake caliper and suspend out of way. DO NOT allow caliper to hang by hydraulic hose. 2. Separate tie rod end from steering knuckle. Remove axle shaft from steering knuckle hub using a soft mallet. On models with ball and cage type right axle shaft, remove support bearing retainer-to-block bolts. See Fig. 4 . 3. On all models, pry right axle shaft from transaxle using screwdriver. See Fig. 1 . On M/T models, pry left axle shaft from transaxle using screwdriver. On A/T models, insert screwdriver through right axle shaft hole in differential, and drive out left axle shaft. See Fig. 2 1. Place axle shaft in soft-jawed vise with inner joint facing up. Remove boot clamps. See Fig. 4 . Mark slide joint housing and inner race in relation to axle shaft for reassembly reference. 2. Remove and discard snap ring “A”. See Fig. 3 and Fig. 4 . Remove slide joint housing. Remove snap ring “C”. Remove cage, inner race and balls as an assembly. Remove snap ring “B”. Cover axle shaft splines with tape. Remove boot. 3. To disassemble support bearing and retainer assembly on right axle shaft, remove dust shield and snap ring “D”. See Fig. 4 . Press axle shaft out of support bearing and retainer assembly. Remove snap ring and dust shield from retainer. Using bearing driver and hammer, drive support bearing out of retainer.

TOYOTA AND LEXUS HIGHLANDER HYBRID REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-03-2012

download
Engine and Vehicle Identification Chart………………………………………..4-2 General Engine Specifications………4-2 Engine Tune-Up Specifications……..4-2 Capacities ………………………………….4-3 Valve Specifications …………………….4-3 Crankshaft and Connecting Rod Specifications……………………..4-3 Camshaft and Bearing Specifications ……………………………4-4 Piston and Ring Specifications……..4-4 Torque Specifications………………….4-4 Wheel Alignment ………………………..4-5 Tire, Wheel and Ball Joint Specifications ……………………………4-5 Brake Specifications ……………………4-5 Scheduled Maintenance Intervals……………………………………4-6 STEERING AND SUSPENSION ………………4-28 A Air Bag…………………………………….4-28 Disarming ……………………………4-28 Precautions ………………………….4-28 Alternator …………………………………..4-7 B Brake Caliper ……………………………4-30 Removal And Installation……….4-30 C Camshaft and Valve Lifters…………4-14 Inspection ……………………………4-16 Removal & Installation…………..4-14 CV-Joints………………………………… 4-24 Overhaul ……………………………..4-24 Cylinder Head …………………………..4-10 Removal & Installation…………..4-10 D Disc Brake Pads………………………..4-32 Removal And Installation……….4-32 E Engine Assembly ………………………..4-7 Removal & Installation…………….4-7 Exhaust Manifold ………………………4-12 Removal & Installation…………..4-12 F Front Crankshaft Seal………………..4-14 Removal & Installation…………..4-14 Front Halfshaft………………………….4-23 Removal & Installation…………..4-23 Front Strut ……………………………….4-28 Removal & Installation…………..4-28 Front Wheel Bearing………………….4-29 Fuel Filter ………………………………..4-21 Fuel Injector……………………………..4-22 Removal & Installation…………..4-22 Fuel Pump ……………………………….4-21 Removal & Installation…………..4-21 Fuel System Pressure………………..4-21 Relieving ……………………………..4-21 H Heater Core………………………………..4-7 Removal & Installation…………….4-7 Hybrid Transaxle Assembly…………4-22 Removal & Installation…………..4-22 I Ignition Timing ………………………….. 4-7 Adjustment…………………………….4-7 Intake Manifold …………………………4-11 Removal & Installation…………..4-11 L Lower Ball Joint………………………..4-29 Removal & Installation…………..4-29 Lower Control Arm……………………4-29 Removal & Installation…………..4-29 O Oil Pan…………………………………….4-18 Removal & Installation…………..4-18 Oil Pump …………………………………4-18 Removal & Installation…………..4-18 P Pinion Seal ………………………………4-27 Removal & Installation…………..4-27 Piston and Ring………………………..4-21 Positioning ………………………….4-21 Power Rack And Pinion Steering Gear…………………………..4-28 Removal & Installation…………..4-28 R Rear Halfshaft………………………….. 4-24 Removal And Installation……….4-24 Rear Main Seal…………………………4-19 Removal & Installation…………..4-19 Rear Strut…………………………………4-28 Conventional Strut Overhaul…..4-28 Removal And Installation……….4-28 Rear Traction Motor…………………..4-22 Removal & Installation…………..4-22 Rear Wheel Bearing…………………..4-29 Removal And Installation……….4-29 T Timing Belt ………………………………4-19 Removal & Installation…………..4-19 V Valve Lash ……………………………….4-17 Adjustment…………………………..4-17 W Water Pump ……………………………..4-10 Removal & Installation………..

Related Content:

how to install running boards on honda pilot, nissan ka20 16 valve cyl head gasket replacement, 2002 highlander brake torque, 2001 chevrolet monte carlo radiator removal, 2006 sienna liftgate struts replacement video, zx2 vct replacement instructions, nissan ka20 timing marks, Toyota 14b engine torque specification for cylinder head big end and valve clearance, replace alternator on honda ridgeline, quicksilver isolators pdf

1994 Ford Explorer SPINDLE AND SHAFT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
Removal 1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub. See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION. 2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if equipped) and splash shield. 3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 . 4. Remove left shaft assembly (if required). On all applications, wrap spindle in protective cloth and place second step of spindle in soft-jawed vise. 5. On Explorer and Ranger, remove oil seal using slide hammer and Seal Remover (TOOL-1175-AC). Remove needle bearing from spindle. Press seal from shaft assembly. See Fig. 9 . 6. On Bronco and F150, remove needle bearing and oil seal using slide hammer and Cup Puller (T77F- 1102-A). Press seal from shaft assembly. Installation 1. Clean all dirt and grease from spindle bearing bore. Ensure bearing bore is free of nicks and burrs. On Explorer and Ranger, install seal on shaft assembly using press and Seal Installer (T83T-3132-A). 2. On Bronco and F150, install seal on shaft assembly, with seal lip toward spindle. On right side applications, install rubber boot and NEW keystone clamps on stub shaft. Install right shaft assembly into stub shaft, with stub shaft missing spline aligned with shaft assembly. 3. Ensure splines are fully engaged. Install rubber boot over assembly and tighten keystone clamps. On left axle applications, install shaft assembly through steering knuckle, and engage in splines. 4. Install needle bearing in spindle, with manufacturer identification mark facing away from spindle bore. For bearing installation, use Handle (T80T-4000-W), and Bearing/Seal Installer (T83T-3123-A for Explorer and Ranger; T80T-4000-S for Bronco and F150).

Related Content:

2005 f150 half wrap, how to replace a turbine speed sensor on a 1998 ford explorer, remove shaft 326rx service manual, spindle nut torque 2007 ford 150

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 15-06-2012

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

Toyota T50 5 Speed Transmission Electronic Speedo Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 19-04-2012

download
I have intentionally left the photos large, to try to clarify any detail I did not explain in the text. This modification DOES require the use of a lathe, I have tried to write it so as to allow you to go to your local machine shop, brother in law, mate or anyone with a lathe…and it will be done correctly Much thanks to John O’Rielly (PLAGER 7) in Brisbane for passing on the information and problems he had with this modification. Fig.1Standard Drive Assemblies T50 left and AE101 right T50 Speedo Drive Adaption Rev 1 Feb 2003 2 Step One:- Dissassembly T50 Drive:- Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime. Fig.2 T50 Drive Disassembled T50 Speedo Drive Adaption Rev 1 Feb 2003 3 AE101 Drive:- Disassembly is similar to T50, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing and shaft to remove oil, grease and road grime. Fig.3 AE101 Drive Disassembled T50 Speedo Drive Adaption Rev 1 Feb 2003 4 Step Two:- Shortening the Drive Shaft Drive Shaft:- The T50 drive shaft needs to be shortened to a similar length to the AE101. I reassembled the AE101 shaft and housing, and then measured from the top face of the AE101 housing down to the top of the AE101 drive shaft. ( Fig.4) Record this reference depth, (I got 17mm) . Fig.4 Drive Shaft Depth Std AE101 Shaft & Housing The T50 drive shaft will need to be shortened to give the same depth as measured in Fig.4. When I did mine, (and a few others), I found I needed the T50 shaft to be 68.0mm long. Fig.5 Fig.6 The drive shaft is hardened, so I used a belt linisher to shorten the shaft, it could as easily be done on a fine grinding wheel. Remember slowly does it, regular checks of depth in housing and do not let the shaft get too hot during grinding/linishing, this will affect the heat treatment and consequently affect the strength of the drive dogs on the shaft end. Carefully deburr and chamfer, end detail should be similar to original AE101

Related Content:

ax4n endplay specification, manually disengage 4 wheel drive in durango, 1997 dodge ram 1500 tailshaft diagram, 2008 ford f150 driveshaft, repairing rear pinion oil seal 2002 ford explorer sport trac 2wd, expidition drive shaft retaining bolts, drive cycle for toyota corolla 2001, Driveshaft for 2002 Ford F-150 diagram, toyota tundra 2000 4 wheel drive diagnosis, 08 KIA SORRENTO CENTER BEARING

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 25-01-2012

download
Repair Procedure 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. Production Change Information Parts Information Repair Procedure STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 3 of 4 3. Remove the No. 2 steering intermediate shaft assembly. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 7. Install the No. 1 steering column hole cover sub-assembly onto the steering gear with a NEW clamp. Repair Procedure (Continued) B A a No. 2 Steering Intermediate Shaft Intermediate Shaft STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 4 of 4 8. Install the No. 1 steering column hole cover sub-assembly by attaching clip B onto the body and installing the No. 1 hole cover onto the body with clip A. NOTE: Make sure that the lip of the No. 1 hole cover is NOT damaged. 9. Install the No. 2 steering intermediate shaft assembly. A. Align the matchmarks (“a”) on steering intermediate shaft and the steering sliding yoke and temporarily install them with bolt B. Torque: 35 Nm (360 kgfcm, 26 ftlbf) B. Ensure the wheels are straight. C. Install the No. 2 intermediate shaft and the intermediate shaft with bolt A. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 10. Install the column hole cover silencer sheet. A. Install the column hole cover plate with the 2 clips. B. Install the floor carpet. 11. Remove the steering wheel holder from the vehicle. 12. Road test the vehicle to verify the repair and confirm that the steering wheel is centered.

Related Content:

07 ford escape intermediate drive shaftpassenger side, 2003-2011 ford crown vic intermediate steering shaft removal, 3024 CAT Rocker Shaft Assembly, 91 Dakota Intermediate Steering Shaft, 92 Dakota Intermediate Steering Shaft, cruze cam cover crack, steering pitman shaft drawing 91 dodge dakota 2 wheel drive

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, remove front diff bearing in navagator, remove rear axle on a 02 mustang, 2006 gmc envoy cv drive axles, remove right side axle on a 2001 toyota sienna, 2005 ford explorer rear axle nut size