buick lucerne 2007 drain plug coolant

You search PDF repair manual about buick lucerne 2007 drain plug coolant, if there are search results will appear below. If search results do not exist, please search by others keyword.



  buick lucerne 2007 drain plug coolant Direct Download speed 5432 Kb/s

  buick lucerne 2007 drain plug coolant Full Version speed 8172 Kb/s



1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

0

Filed Under (Saturn Manuals) by admin on 19-05-2012

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, crank sensor location on 6 7 power stroke, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how to drain radiator on 2007 ford fusion 2 3 L, hino j500 pump timing marks

2001 Ford Taurus/ Sable Cooling System Draining Filling and Bleeding Workshop Manual

0

Filed Under (Ford Manuals) by admin on 19-02-2011

download
CAUTION: Vehicle cooling systems are filled with Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or an equivalent meeting Ford specification ESE-M97B44-A. NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle. For additional information, refer to Section 100-02 . 3. Remove the front splash shield. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding With RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling Without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants may degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolant unless it meets the requirement of specification ESE-M97B44-A. Not all coolant recycling processes meet this specification. Use of such a coolant may harm the engine and cooling system components. 1. Install the front splash shield. 2. Lower the vehicle. 3. Fill the degas bottle with the correct engine coolant mixture. 4. Install the pressure relief cap. 5. Move the temperature blend selector to the full warm position. 6. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Run the engine until it reaches operating temperature. 7. Add the correct coolant mixture to the degas bottle until the coolant level is between the COOLANT FILL LEVEL marks. 8. Turn off the engine and allow the cooling system to cool. Recheck the coolant level and fill the cooling system to the FULL mark on the degas bottle. 9. WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Repeat Steps 3 through 8 until the reservoir level is OK. Bleeding Without RADKITPLUS 1. Bleed the cooling system as follows: * Select the maximum heater temperature and blower motor speed settings. Position the control to discharge air from the A/C vents in the instrument panel. * WARNING: Do not stand in line with or near the engine cooling fan blade when revving the engine. Start the engine and allow it to idle. While the engine is idling, feel for hot air from the A/C vents. * CAUTION: If the air discharge remains cool and the engine coolant temperature gauge does not move, the engine coolant level is low in the engine and must be filled. Stop the engine, allow it to cool and fill the cooling system. Start the engine and allow it to idle until the normal operating temperature is reached. Hot air should discharge from the A/C vents. The engine coolant temperature gauge should maintain a stabilized reading in the middle of the NORMAL range and the upper radiator hose should feel hot to the touch. * Shut the engine off and allow it to cool. * Check the engine for coolant leaks. * Check the engine coolant level in the degas bottle and fill it as necessary.

Related Content:

4D35 engine repair manual, 6m70 wiring diagram, 2000 Nissan sentra 1 8 engine bolt torque diagram, so5d engine repair manual, so5d engine, TOYOTA SO5D SERVICE MUNAL, what causes damage to a flywheel on a 2004 yukon, SO5D OBD ll Code, 2005 chevy impala motor diagram, Position of sensors in mitsubishi 4m 51 engine

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 2007 kia rio service manual, schematic for front brakes on 2005 Buick Rendezvous, 4t65e service manual online, 2007 Chevy Colorado Gas Tank Seal replace, w584a lincoln, 200lolds aleroraditor system, pontiac 2007 g6 remove radiator cover

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, how to check radiator fluid level pontiac grand prix, Low coolant light olds intrigue, evap sensor on 2002 suburban, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 2002 mercury sable cooling system, 2006 Envoy low idle

2003 Buick Truck Rendezvous Draining and Filling Cooling System Repair Manual

0

Filed Under (Buick Manuals) by admin on 08-06-2012

download
Draining and Filling Cooling System Notes Draining and Filling Cooling System Draining Procedure Important: Do NOT add any engine coolant supplement sealant pellets to the cooling system. Drain and refill the engine cooling system every 5 years or 240 000 km, (150,000 ml) , whichever occurs first. 1. Park the vehicle on a level surface. 2. Remove and clean the coolant recovery reservoir. Caution: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap its removed while the engine and radiator are still hot. 3.1. Slowly rotate the cap counterclockwise to the detention tab. Do not press down while rotating pressure cap. 3.2. Wait until any residual pressure, indicated by a hissing sound, is relieved. 3.3. After all hissing stops, press down on the radiator cap and rotate the cap counterclockwise in order to remove the cap. Important: Recover and store used coolant in a used coolant holding tank and submit the used coolant for recycling on a regular basis. Do NOT pour used coolant down the drain. Ethylene glycol antifreeze is very toxic. Disposing of ethylene glycol into the sewer system or ground water is both illegal and ecologically unsound. 4. Place a drain pan under the radiator drain cock in order to collect all of the used coolant. 5. Open the radiator drain cock. If only partial cooling system draining is required, drain enough coolant to perform the procedure 6. Open the air bleed valve on the thermostat housing 2 full turns. 7. Open the air bleed valve above coolant pump 2 full turns. 8. Place a drain pan under the engine block drains in order to collect the used coolant. Important: Allow the coolant to drain completely

Related Content:

how install a coolant tank on 2005 Jaguar xj8L, how to drain radiator on 2003 suburban, instructions for using COOL SURGE cooler

2007 TOYOTA TUNDRA SUPERCHARGER FIT KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 20-03-2012

download
1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 3, save this coolant as it will be reused. CAUTION: To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause the hot engine coolant and steam to blow out from the radiator. (h) All parts that are removed and not reused should be saved for the customer, i.e., “discard” means to save for the customer 2. Cover Removal. (a) Remove the engine V-bank cover by Lifting the front of the cover and pulling away from the firewall (Fig 2-1). Discard these parts. (b) If installed, remove the No. 1 engine under cover (Fig 2-2) by removing the 3 screws and 5 bolts. Save these parts for reuse. 3. Drain Engine Coolant. CAUTION: Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns. (a) Loosen the radiator drain cock plug (Fig. 3-1). (b) Remove the radiator cap. Then drain the coolant from the radiator into a clean container so it can be reused (Fig. 3-1). (c) Loosen the 2 cylinder block drain cock plugs (Fig.3-1). Then drain the coolant from the engine and save for reuse. (d) Tighten the 2 cylinder block drain cock plugs. Torque: 13 Nm (10 ft lbf) 4. Fan and Shroud Removal. (a) Remove the upper radiator hose. Mark the radiator end of this hose with a marker or tape. This hose will be re-installed inverted and the mark will help identify the ends. (b) Loosen the 4 nuts holding the fluid coupling fan (Figs. 4-1). (c) Remove the fan/generator V-rib belt. Discard this belt as it will be replaced by a new belt. (d) Disconnect the reservoir hose from the upper radiator tank. (e) For vehicles with Trailer Towing System: Detach the claw to open the No. 1 hose clamp on the side of the fan shroud (Fig 4-2). (f) Remove the 2 bolts holding the fan shroud (Figs 4-3). Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan. Retain these parts for reuse. Temporarily re-install the 4 nuts to keep the pulley in place (reference Fig 4-1). Do not tighten. CAUTION: Be careful not to damage the radiator core. It is helpful to protect the radiator core with a piece of cardboard to prevent damage during subsequent steps. 5. Air Cleaner Lower Box Replacement. (a) Remove the air cleaner hose by disconnecting the vacuum and ventilation hoses and loosening the 2 clamps. (Fig 5-1). Discard this hose and clamps

Related Content:

location of draincock on 2007 ford fusion, 05 monte carlo radiator drain, thumb screw missing on 2004 4 3 silverado to drain coolant, procedure for replacing radiator liquid on 2009 Buick Lucerne, picture of 1996 cadillac sedan deville radiatot and hose, is the radiator in 2007 mountaineer one piece, instructions on how to install a radiator in a 2006 Buick LaCrosse, install lowere radiator hose 2007 pontiac g6 3 5, diagram radiator drain plug 3 1 lt jeep, 2007 honda odyssey a/c not working

1993-2002 Volkswagen Golf, Jetta, GTI, Cabrio A/C controls and mechanical components service manual

0

Filed Under (Volkswagen Manuals) by admin on 09-07-2012

download
1 – . Dust and pollen filter Where applicable 2 – . Plenum cover Removing/installing – -”> 3 – Evaporator water drain valve Located behind bulkhead insulation Removing/installing Fig. 2 Removing and installing evaporator water drain valve 4 – . Heater core connections and vacuum hose guide 5 – . Fresh Air/Recirculating Flap Two-Way Valve N63 Valve open when voltage applied Vacuum hose layout Vacuum hose layout 6 – . Coolant Fan Control (FC) Control Module J293 With fuse Fuse Strip S88 (1993 m.y.) With fuses Coolant Fan Second and Third Speed Fuse S107 and Coolant Fan First Speed and A/C Clutch Fuse S108 (1994 m.y. micro ) Connector terminal identification: micro 09.93 Fig. 5 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 ( 09.93) 10.93 micro Fig. 6 Connector terminal identification of Coolant Fan Control (FC) Control Module J293 (10.93 ) 7 – . Vacuum reservoir Insert vacuum hose 30 mm (1.2 in.) into reservoir Removing/installing Fig. 7 Removing and installing vacuum reservoir A/C and heating system components, engine compartment Vacuum hose Vacuum hose layout Vacuum hose layout 9 – . A/C Cut-Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 A/C Cut-Out Thermal Switch F163 only on vehicles with engine codes AAA, AAZ, ABA, ACC A/C Cut-Out Thermal Switch F163 switches A/C Clutch N25 off at high engine coolant temperature; OFF (switch open) above 119 degree C (246 degree F); ON (switch closed) below 112 degree C (234 degree F) Third Speed Coolant Fan Control (FC) Thermal Switch F165 only on vehicles with 3- speed coolant fan motor Third Speed Coolant Fan Control (FC) Thermal Switch F165 switches radiator coolant fan to 3rd speed as engine coolant temperature increases; 3rd speed ON (switch closed) above 112 degree C (234 degree F); OFF (switch open) below 108 degree C (226 degree F) Removing and installing (engine code AAA) Fig. 3 Removing and installing A/C Cut- Out Thermal Switch F163 and Third Speed Coolant Fan Control (FC) Thermal Switch F165 (2.8 liter VR6 engine code AAA) Removing and installing (engine code ABA) Fig. 4 Removing and installing A/C Cut- Out Thermal Switch F163 (2.0 liter engine code ABA) 10 – . Condenser* 11 – . Pressure relief valve*

Related Content:

wiring diagram for the drivers side front electric window switch on a 1998 ford contour, 02 Jetta Fan Control Module, 2002 lincoln ls cooling system diagram, fan fuse for 1995 chevy lumina, fan sensor vw beetle how to change, how to replAce mounting on evap canister on 2001 f150 to truck body, Mazda MPV Fan Control Module 2002

2004 Chevrolet Aveo SPARK PLUG REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 12-06-2012

download
Courtesy of GENERAL MOTORS CORP. 2. Loosen the 4 bolts and remove the engine cover. Fig. 117: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. 3. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Courtesy of GENERAL MOTORS CORP. 2. Loosen the 4 bolts and remove the engine cover. Fig. 117: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. 3. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Fig. 118: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. NOTE: Be sure plug threads smoothly into cylinder head and is fully seated. Use a thread chaser if necessary to clean threads in cylinder head. Cross- threading or failing to fully seat spark plug can cause overheating of plug, exhaust blow-by, or thread damage. Follow the recommended torque specifications carefully. Over or under-tightening can also cause severe damage to engine or spark plug. 2. Install the spark plugs to the engine. Tighten: Tighten the spark plugs to 25 N.m (18 lb ft). 3. Install the spark plug wires to the spark plugs. Refer to Spark Plug Wire Replacement . Fig. 119: Identifying Cover Screws Courtesy of GENERAL MOTORS CORP. 4. Install the engine cover and tighten the 4 bolts. Tighten: Tighten the engine cover bolts to 3 N.m (31 lb in).

Related Content:

ISX 12 drain plug thred, changing spark plugs on 2008 avalon, 2004 chevy aveo spark plug wire replacement, Ford 500 Spark Plug Change, how to change spark plugs in 2009 Aveo, spark plug calibration, manual shifter not working on 2008 nissan titan, loctite spark plug, is 1999 pontiac grand am obd2, intermitant misfire in morning 2008 torrent

TOYOTA 4RUNNER A750E (F) AUTOMATIC TRANSMISSION SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 02-04-2012

download
The ATF level gauge (dip-stick) has been discontinued, and the ATF inspection method and the oil level inspection method have been changed. This mechanism consists of a refill plug, overflow plug, ATF temperature sensor No.2, and A/T OIL TEMP temperature warning light. ATF Filling procedures using SST (09843-18020): When a large amount of ATF needs to be filled (i.e. after removal and installation of oil pan or torque converter), perform the procedure from step 1. When the small amount of ATF is required (i.e. removal and installation of the oil cooler tube, repair of oil leak), perform the procedure from step 7. 1) Raise the vehicle keeping it level. 2) Remove the refill plug and overflow plug. 3) Fill ATF from the refill plug until it overflows from the overflow plug. 4) Install the overflow plug. 5) Fill the specified amount of ATF determined by procedure and install the refill plug. Example 6) Lower the vehicle down. 7) Use the SST (09843-18020) to short the terminals Tc and CG of the DLC3 connector: 8) Start the engine and allow it to idle. A/C switch must be turned OFF. 9) Move the shift lever slowly through each of the positions from the P to the L position, and move it back to the P position. 10) Move the shift lever from the D position, and quickly move then back and forth between N and D (once per less than 1.5 seconds) for at least 6 seconds. This will activate the oil temperature detection mode. Standard: The A/T OIL TEMP warning light remains illuminated for 2 seconds and it goes off. 11) Return the shift lever to the P position and disconnect the terminal Tc. 12) Idle the engine to raise the oil temperature. 13) Immediately after the ATF OIL TEMP warning light turns on, lift the vehicle up. The A/T OIL TEMP warning light will indicate the ATF temperature according to the following table. (Insert table here) 14) Remove the overflow plug and adjust oil quantity. If the ATF overflows, go to step 17, and if the ATF does not overflow, go to step 15. 15) Remove the refill plug. 16) Fill ATF to the refill plug until it flows out from the overflow plug. 17) When the ATF flow slows to a trickle, install the overflow plug. 18) Install the refill plug (only if the refill plug has been removed). 19) Lower the vehicle down. 20) Turn the ignition switch OFF to stop the engine. For details about the ATF Filling procedures, see the 2004 4Runner Repair Manual (Pub. No. RM1059U)

Related Content:

when do plugs need change 2005 kia sorento, 1999 f-150 draining torque converter drain plug, 2004 toyota 4runner owners manual, 3rd gen 4Runner transmission cooler install, digital 2004 toyota 4runner setvice manual, fit glow plugs in 04 rodeo, procedure for filling atf on ford explore w/o dip stick, toyota transmission manuals pdf download

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, schematic for 99 taurus power steering, how to change power steering pump 2009 acada, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, how to replace 2003 impala power steering pump

Related Content:

yhs-sgm_fb, wiring diagram for 2005 kia sedona engine cooling fan temperature sensor, bye pass c15 timming sensor, replacing s radiator 2001 silhouette oldsmobile, crank sensor location on 6 7 power stroke, 2001 oldsmobile intrique coolant system diagram, location of air temp sensor on 2001 toyota celica, 2001 mitsubishi montero limited head gasket repair procedure pdf download, how to drain radiator on 2007 ford fusion 2 3 L, hino j500 pump timing marks