buick reatta dash problems

You search PDF repair manual about buick reatta dash problems, if there are search results will appear below. If search results do not exist, please search by others keyword.



  buick reatta dash problems Direct Download speed 5432 Kb/s

  buick reatta dash problems Full Version speed 8172 Kb/s



1999 Toyota Corolla Radio Replacement

0

Filed Under (Toyota Manuals) by admin on 12-05-2011

download
The radio is secured to the frame of the vehicles dash with screws located behind the plastic dash panel surrounding the radio. This plastic dash panel unsnaps from the body of the vehicles dash. STEP 2 : The bottom of the plastic dash panel, just below the bottom of the radio, can be lifted up. Look up from the below the radio and you will notice rectangular openings or insertion points where a flat tool can be inserted to pry out the bottom of the plastic dash panel. With a flat head screwdriver or other flat object, pry out the bottom of the plastic dash panel STEP 3 : Once the bottom edge of the plastic dash panel has been pulled out, the sides of the plastic dash panel will begin to separate from the body of the vehicles dash. You will now be able to put your fingers into the openings on the sides of the plastic dash panel. Gently pull the plastic dash panel until it unsnaps from the body of the vehicles dash. Remove Factory Radio Move to: Wire New Radio Section Wiring The New Radio Move to: Mounting New Radio Section The Install Doctor STRONGLY recommends purchasing a ‘DIN’ radio for this vehicle. ‘DIN’ radios are a direct replacement for the Toyota radio in this vehicle. More information is available in the Mounting New Radio section. Mounting The Radio Options STEP 4 : Once all the clips on the plastic dash panel have been unsnapped, the dash can be pulled out. The top of the plastic dash panel will have wires attached to the clock, hazard and defrost switches. You do NOT need to unplug the connectors plugged into them. Move the plastic dash panel up and set it on top of the body of the dash. STEP 5 : The radio is held in with four (4) phillips screws / 8 mm bolts . Remove the screw/bolts. Pull the radio forward. Unplug the antenna cable, and 2 white connectors from the rear of the radio

Related Content:

toyota venza dashboard repair manual, Plastic Bezel Watch Instructions, 1995 ford 555d backhoe dashboard warning light, tsb #00-25-6, set hino dashboard clock, plastic bezel 1011 watch manual, no sienna dash lights, how to renove upper dah panel 2013 avalon, how install 2001 camaro dash panel, hino 268 dash warning lights

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

Related Content:

kia besta electrical wiring diagram pdf, mercedes benz actros wiring manual, 1983 monte carlo window wiring, vp44 9 pin connector, toyota alphard wiring diagram, PIN DATA 2005 скачать, mercedes actros 2540 owners manual pdf, kia besta wiring diagram, elect repair for cadillac dashboard replacement, actros dash bourd wire daigram

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering

2004 Toyota Prius EV (Electric Vehicle) Button Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Time and Difficulty: I found the install to be moderately difficult and pretty time-consuming (about 3 hours) ; others have found it simple and report they have done it in as little as 30 minutes. Your experience will depend on your familiarity with the tools and electronics. I, personally, found insertion of the connection pin into the HV ECU plug to be difficult and almost got the first pin irrevocably stuck in the slot. I spent quite a bit of time with that part alone. I also found threading the wire behind the dash to be fairly tricky. I think the average person, not encountering any problems, could do this job in about 1-1½ hours. Procedure in Brief: 1) Remove bottom cover of steering wheel 2) Locate and unplug flasher plug 3) Open plug and remove 1-3 unused connector pins 4) Reattach steering wheel cover 5) Dismantle part of dash (vents) and remove lower glove box 6) Locate HV ECU (gray plugs) and remove lower plug 7) Solder wire to connector pin and insert into ECU plug (#27) 8) Splice EV button ground wire into ECU plug ground wire (#1) 9) Plug ECU plug back into the ECU 10) Thread wire behind dash to opening near dimmer switch 11) Attach switch to cover and solder wires in place 12) Reassemble the dash 13) Test Procedure in Detail: *Review ALL steps before proceeding and be sure you understand all terms used and you’ve looked at all diagrams and pictures. 1) Remove the bottom cover of the steering wheel by releasing the steering wheel adjustment handle and unscrewing the silver screw in that recess. 2004_prius_evv2.doc Page 4 of 20 Last updated March 13th, 2004 Then, turn the steering wheel 90 degrees right and remove the black screw that becomes visible on the right side of the steering column. Then turn the wheel 180 degrees left (90 degrees from normal position) and remove the black screw on the left side of the steering column. Carefully pull down on the lower portion of the steering column cover until it releases. Mine was a bit stiff/stuck to the upper part and you may need to carefully use a butter knife or screwdriver to start prying them apart. 2004_prius_evv2.doc Page 5 of 20 Last updated March 13th, 2004 2) Locate and unplug the white flasher plug visible just on the left side of the bottom of the steering column. 3) 2 little clips keep a cover locked in place. Pull those apart and remove the cover. Inside you’ll see lines of silver connector pins–some with wires attached, some without. You should remove between 1 and 3 of those pins–2 is probably safe, 3 might be better, since if you plan to install an OEM button at some point, you’ll probably need more pins for that. (You need one pin for the procedure, but it’s handy to have a back-up.) To remove the pins, you can use your paper clip to start the process of sliding them out, and then they just pull right out. 2004_prius_evv2.doc Page 6 of 20 Last updated March 13th, 2004 Stick them to a piece of tape or put them somewhere secure so you can find them later. Snap the cover back into place, and plug the flasher plug back in. 4) Replace the steering wheel cover by reversing the process. Be sure everything’s aligned properly and that there are no gaps. 5) Now you’ll need to dismantle part of the dash to get access to the ECU and other areas. First, open the top and bottom glove box doors. Squeeze the inside sides of the lower glove box together to get the catches past the portion of the dash frame that keeps the door from falling all the way open. Then pull the entire door straight toward you – it will unclip from the hinges at the bottom of the glove box. 2004_prius_evv2.doc Page 7 of 20 Last updated March 13th, 2004 You may also need to unclip the little hydraulic piston that keeps the door from falling open too quickly. Next, grasp the bottom of the silver vent piece next to the glove box. Pull it toward you firmly. It should unclip at the bottom first. Then pull the whole unit straight out

Related Content:

2004 3 5 isuzu rodeo repair manual pdf no registration, 2004 Chevrolet Malibu Classic Manual Free, 2004 Sienna Fuse Box Diagram, reset security on 2004 maxima, 2004 mazda 3 headlight adjustment, diagram firing orden to freelander 2003 4wd, how to reset computer on 2004 chevy impala, 2004 gto repair manual, all air vents open on 2004 ford explorer, 2004 sienna thermostat replacement

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 buick century service manual free, 2000 saturn sl1 owners manual, 560sl repair 1988, 2000 Chevy Impala Passkey Bypass is there a fuse, diagrama buick century 2002 pmc, park avenue ac control schematic, is it hard to replace the ac compressor on a 2001 mercury cougar 2 5l 12valve car, 2000 chevrolet suburban haynes

2005 TOYOTA AVALON TVIP V4 (REMOTE ENGINE STARTER) INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 2 of 33 pages Issue: C 02/02/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Visassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly if equipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process. FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Step g) NOTE: Do not perform this step if the vehicle has Smart Entry. (g) Remove the driver’s step cover. (Fig. 1-7) Screw Fig. 1-5 10mm Wrench, Phillips Screwdriver Bolt Glove Box Assembly Cowl Cover Fig. 1-4 Nut Fig. 1-6 Nylon Panel Removal Tool, Phillips Screwdriver Screws (x3) Glove Box Assembly Trunk Opener Cancel Switch Connector Fig. 1-7 Step Cover Nylon Panel Removal Tool
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 4 of 33 pages Issue: C 02/02/05 FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Steps h-l) NOTE: Do not perform this step if the vehicle has Smart Entry. (h) Remove the driver’s cowl cover. (Fig. 1-8) (1) Remove the one nut securing the cowl cover. (i) Remove the hood release cable. (Fig. 1-9) (1) Do not bend the hood release cable. (j) Open the screw cover on the lower dash cover. Insert the tip of a Nylon Panel Removal Tool in the upper slot to loosen it. (Fig. 1-9) (1) Remove one screw and one bolt securing the lower dash cover. (k) Remove the lower dash cover. (Fig. 1-10) (1) Disconnect the temperature sensor (connector and aspirator hose) from the lower dash cover if equipped. (l) Carefully remove the driver side airbag assembly. (Fig. 1-11) (1) Remove four bolts securing the driver side airbag assembly. (2) Be careful not to get cut by the sharp metal edges. (3) Do not disconnect the airbag assembly. (4) Use the empty V4 kit box to support the airbag assembly on the floor

Related Content:

Prius upper glovebox door hinge, Prius repair glovebox door, toyota venza glove compartment box, how to take the back off a blu dask 3 5, colbalt where is the strarter located, 2005 toyota tacoma airbag fuse location, 2005 toyota corolla under carriage, clicking noise by glove box 2008 chevy impala, loud clicking noise in glove box impala, PICTURE OF GLOVE BOX LOWER BRACE ON CHEVY UPLANDER

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

w584a lincoln, 2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, how to change intake gasket 2007 grandprix, schematic for front brakes on 2005 Buick Rendezvous, 200lolds aleroraditor system, 2007 Chevy Colorado Gas Tank Seal replace, 2007 kia rio service manual, pontiac 2007 g6 remove radiator cover

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, 2005 buick century code p0455, hunter 9700 user manual, 2000 buick lesabre custom manual, how to change the lower control arms on a 2005 Titan pdf, hunter lift L401, integrated wheel end FOR F150, location of fuses and relays 2003 buick park avenue, Rear Tire wear Mecury Mariner, repair manual on 2001 cadi deville on motor mount

2009-2010 Toyota Venza DIN Head Unit Provision With Pocket Installation Manual

0

Filed Under (Toyota Manuals) by admin on 26-02-2012

download
Toyota Venza 2009-2010 1 D isconnect the negative battery terminal to prevent an accidental short circuit. 1 Unclip and remove the trim panel to the right of the shifter. ( Figure A) 2 Remove (1) Phillips screw from the bottom of the climate control then unclip and remove the climate control. (Figure B) 3 Remove (4)10 MM bolts securing the radio. Note: You will need a universal swivel head socket adapter to get to the bottom left bolt. (Figure C) 4 Remove (4) Phillips screws securing the factory radio to the a/c vent panel. ( Figure D) 5 A B C REAR VIEW-RADIO AND A/CVENT PANEL RADIO D Continue to kit assembly . 99-8225G KIT ASSEMBLY 2 REAR VIEW-A/C VENT PANEL A B C D Secure the Radio Housing into the factory a/c vent panel using the factory hardware. (Figure A) 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the aftermarket head unit into the cage and secure. (Figure C) 4 * Note: Refer also to the instructions included with the aftermarket radio. DIN HEAD UNIT PROVISION WITH POCKET Reassemble remaining radio and dash assemblies in reverse order of disassembly. 5 6 Snap the factory vent panel/Radio Housing over dash cavity. (Figure D) 99-8225G KIT ASSEMBLY 3 REAR VIEW-A/C VENT PANEL A B C D Secure the Radio Housing into the factory a/c vent panel using the factoryhardware. (Figure A) 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 2 Slide the head unit into the radio opening until the side clips engage. (Figure C) 3 Snap the Trim Plate into the Radio Housing. (Figure C) 4 * Note: Refer also to the instructions included with the aftermarket radio. ISO DIN HEAD UNIT PROVISION WITH POCKET 5 Snap the factory vent panel/Radio Housing over dash cavity. (Figure D) Reassemble remaining radio and dash assemblies in reverse order of disassembly

Related Content:

metra bbbpc wiring diagram, code fortuner head unit, metra bbbpc, toyota venza 2009 manual

1994 Cadillac DeVille Concours Procedure to Disable Illumination of Service Indicator AFTER the Installation of Passive Struts/Shocks

0

Filed Under (Cadillac Manuals) by admin on 11-06-2011

download
Run a wire from a switched ignition (hot in Run) source to relay pin 85. 1992-1993 Oldsmobile Achieva with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1992-1994 Buick Skylark with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1993-1996 Buick Park Avenue with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1991-1995 Oldsmobile Ninety Eight with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1994-1999 Pontiac Bonneville with Computer Command Ride (CCR) The feedback strut/shock assemblies are still available for these vehicles. However, if the customer desires to reduce the repair expense, the following steps may be taken to allow installation of non-feedback assemblies and the disabling of the malfunction indicator lamps. This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. Parts Information The following parts are required to make the correction on the 1993 Eldorado/Seville and the 1994-1995 DeVille. Parts are currently available from GMSPO

Related Content:

1993 cadallic deveal service manuel, 1992 park avenue repair manual, program vin to computer 1999 cadillac deville, fix ac in 1995 sudan deville, buick park avenue 1992 repair manual, 2002 cadillac deville dts passkey 3 reset, 1999 buick park avenue repair manual free pdf, 1994 buick century repair manual pdf, 1993 cadillac deville no pressure, where is the vats computer on a 1994 cadillac deville

Related Content:

toyota venza dashboard repair manual, Plastic Bezel Watch Instructions, 1995 ford 555d backhoe dashboard warning light, tsb #00-25-6, set hino dashboard clock, plastic bezel 1011 watch manual, no sienna dash lights, how to renove upper dah panel 2013 avalon, how install 2001 camaro dash panel, hino 268 dash warning lights