buick rendezvous dashboard light

You search PDF repair manual about buick rendezvous dashboard light, if there are search results will appear below. If search results do not exist, please search by others keyword.



  buick rendezvous dashboard light Direct Download speed 5432 Kb/s

  buick rendezvous dashboard light Full Version speed 8172 Kb/s



1993 Dodge Dakota FUSE PANEL IDENTIFICATION

0

Filed Under (Dodge Manuals) by admin on 24-05-2011

download
3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights. 9 – 15 Amp (Lt. Blue) Cigarette Lighter. 10 – 20 Amp (Yellow) Windshield Washers & Wipers. 11 – 20 Amp (Yellow) Turn Signals, Rear Wheel Anti-Lock Module. 12 – 10 Amp (Red) Radio. 13 – 4 Amp (Pink) Cluster Lights, A/C & Heater Controls, Cigarette Lighter Light & Ash Receiver Light, Radio Lights & Overdrive Switch Light. 14 – Not Used (1992-93); 15 Amp (Lt. Blue) (1994-95 Airbag Module, Speedometer, Gauges, Telltales. 15 – 2 Amp (Gray) Speed Control. 16 – 5 Amp (Tan) Gauges & Indicator Lights: Low Oil Light, Low Washer Light, Service Reminder Light, Transmission Oil Light, Brake Warning Light, Anti-Lock Brake Warning Light, Fuel Pacer Light, 4WD Indicator Light, Malfunction Indicator Light, Warning Buzzer, Overdrive Switch (1992-93); Transmission Oil Temperature Lamp, 4WD Lamp, Overdrive Module Seat Belt Warning Buzzer (1994-95). 17 – (Blank) Not Used. 18 – (Blank) Not Used. 19 – (Blank) Not Used. 20 – Not Used (1992-93); 25 Amp (Natural) (1994-95) Fog Lamps and Off Road Lamps. 21 – Turn Signal Flasher No additional definition. 22 – Time-Delay Relay No additional definition. 23 – Horn Relay No additional definition. 24 – Hazard Flasher No additional definition. 25 – Warning Buzzer

Related Content:

emission light on impala, 86 ford ranger emission sensors, 2011 dodge durango not charging, 1992 CHEVrolet silverado idle air control assembly calibration specifications, 1992 Grand Marquis Manual, mazda 3 transmission gear indicator light, service 4wd light on silverado, Isuzu NPR Warning Light Icons, slip light on nissan titan, how to reset washer fluid malibu 06

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, 98 amigo isuzu how to remove power steering pump

1989 Honda Accord LXi FUSES AND CIRCUIT BREAKERS IDENTIFICATION / REPAIR MANUAL

0

Filed Under (Honda Manuals) by admin on 19-05-2011

download
1 – 15 Amp Charge Warning Light, Voltage Regulator, Cooling Fan Timer Control Unit, Fuel Cut-off Relay, Speed Sensor, PGM-FI Main Relay, Fuel Pump, Control Solenoid Valves, Emission Control Unit, Speed Sensor (Automatic Seat Belts, 1988-89) 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda 1989 Honda Accord LXi FUSES & CIRCUIT BREAKERS’ ‘Fuses & Circuit Breakers 1986-89 Honda None Sunday, August 10, 2008 12:33:23 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. None Sunday, August 10, 2008 12:33:26 AM Page 1 © 2005 Mitchell Repair Information Company, LLC. ? 2 – 10 Amp Safety Indicator, Shift Lever Position Indicator, Clock & Gauges, Tachometer, Back-Up Lights, Turn Signal Relay & Lights, Integrated Control Unit, Warning Lights, Cruise Control Indicator, Light Dimming Circuit, Automatic Seat Belt Control Unit, Shift Lock Solenoid (1989) ? 3 – 20 Amp Wiper Motors, Washer Motors, Intermittent Wiper Relay, Sun Roof Relays, Power Window Relay ? 4 – 7.5 Amp Cruise Control Unit, Cruise Control Indicator Light ? 5 – 10 Amp Rear Window Defogger Relay, Rear Window Defogger Indicator Light, Heater Control Amplifier, Fan Motor, A/C Compressor Clutch & Relay, A/C Delay Unit, Heater Control Panel ? 6 – 10 Amp Right Headlight Low Beam ? 7 – 10 Amp Left Headlight Low Beam ? 8 – 15 Amp Left Headlight High Beam ? 9 – 15 Amp Right Headlight High Beam, High Beam Indicator Light ? 10 – 7.5 Amp Brake Warning Bulb Check Circuit, PGM-FI ECU, PGM-FI Main Relay, Emission Control Unit ? 11 – 15 Amp Headlight Retractor Control Unit (Up) ? 12 – 15 Amp Power Door Mirrors, EFE Heater Unit, Radiator Fan Relay, Cooling Fan Timer Unit ? 13 – 10 Amp Power Antenna Motor, Stereo Radio/Cassette Player, Power Amplifier (SEi Model) ? 14 – 15 Amp Vanity Mirror Light, License Plate Lights, Taillights, Rear Side Marker Lights, Dash Light Brightness Control Unit, Cigarette Lighter Illumination, Ashtray Light, Headlight Retractor Control Unit (Light-On), Dash & Switch Lights ? 15 – Blank

Related Content:

1981 chevrolet p30 motorhome brake replacement instructions, Honda service manual 1995 accord, 1995 accord repair manual pdf, 2003 buick lesabre lose power for instrument panel and a/c controls, 1989 corvette climate control panel, 2005 honda crv malfunction indicator lamp reset, fuse chart for 2002 chevy silverado 2500 no brake lights, honda accord 61-10 code, fuel circuit outputs on chevy s10, honda accord code 61-1

200-92010 Toyota Camry/ Corolla OE Fit Fog Light Install Instruction

0

Filed Under (Toyota Manuals) by admin on 28-04-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties. 2. Attach the ring terminal with 2 black wires to the 10mm bolt next to the relay 3. Connect the ring terminal from the relay (12v red wire) to the positive terminal of the battery 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector. Seal with 3M Silicone sealant (see picture 1) Picture 1 5. Run the fog light wire harness on the driver side of the car. Use wire ties as needed. 6. Remove dash panels 7. Mount switch into switch knockout on left side of dash 8. From inside the cabin, locate the small connector that were pushed through in step 4. It will be the grommet above the gas pedal 9. Install switch harness 10. T-tap green/black wire from fog light harness to connector E21 pin 11, light green wire (first pin on right). Connector E21 is located on the left side of the steering column (picture 2) Picture 2 11. T-Tap orange/black wire from fog light harness to connector ID pin 3, pink wire (middle third pin from left). Connector ID is left of steering wheel (picture 3) Picture 3 12. Secure with wire ties. 13. Reinstall dash panels 14. Route the fog light wire under car. 15. Remove fog light cover plates and lower splash shields on both sides 16. Insert one side of the fog light into the plastic sleeve and secure other side with supplied Phillip screws (see picture 4

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 200lolds aleroraditor system, 4t65e service manual online, 2007 kia rio service manual, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, schematic for front brakes on 2005 Buick Rendezvous, pontiac 2007 g6 remove radiator cover

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

Steering, Brake And Suspension Specialists Proportioning Valve Diagram

0

Filed Under (More Manuals) by admin on 01-10-2011

download
This diagram is the most common way to plumb a proportioning valve. In some cases, the right front line will be plugged off at the proportioning valve and the left front line will go to a “T” fitting. From the “T” fitting, the front lines then split off and go to the left and right wheels. Our proportioning valve has a warning light switch built in (this is not a stop light switch.) The warning light will detect any loss of pressure, for example, a leaky wheel cylinder. We recommend you wire this light into your system. Any two wire light socket will work. One wire goes to the accessory power and the other goes to the warning light. Our proportioning valves provide four functions: 1. Proportion pressure front and rear 2. 10 psi. residual check valve 3. Metering valve to apply pressure to the rear brakes before the front brakes 4. A brake warning light to detect a loss in pressure Proportioning Valve Plumbing Diagram: There are two proportioning valve lines that connect to the master cylinder provided in our kits. The first is a 90 degree bend with one leg longer than the other. This line must be oriented with the long leg connected into the front top hole of the proportioning valve and the short end in the front hole on the master cylinder. The second line has two 90 degree bends and has color coded fittings. The larger blue fitting goes into the back hole on the master cylinder and the smaller gold fitting goes into the back top hole on the proportion valve as shown in the diagram

Related Content:

wire diagram brake light pressure switch, brake residual valve, residual pressure valve installation diagram, Residual Valve Brake System

1986 Ford Truck F 150 2WD Pickup Emission Maintenance Warning Module-Service Manual

0

Filed Under (Ford Manuals) by admin on 23-06-2012

download
EMISSION MAINTENANCE WARNING MODULE SERVICE INFORMATION ^LAMP – “EMISSIONS/CHECK ENGINE” – EMISSION MAINTENANCE WARNING MODULE – SERVICE INFORMATION LIGHT TRUCK: 1985-89 BRONCO 1985-87 BRONCO II 1985-89 ECONOLINE, F- 150, F-250, F-350 1985-88 RANGER 1986-87 AEROSTAR ISSUE: The Emission Maintenance Warning “EMW” module operates a light that is located on the instrument panel. For 1985-87 model year vehicles, the light will display the word “EMISSIONS”. For 1988-89 model year vehicles, the light will display the words “CHECK ENGINE”. When the light is lit, it is indicating that the 60,000 mile emission maintenance should be performed. After the maintenance is performed the EMW module must be reset to zero time. Another type of module is the “IMS” module. This module is not part of the light circuit and does not require maintenance. At a predetermined time, the IMS module directs the EEC IV processor to make a strategy change. A third type of module is the “COMBO” module. This module combines the functions of the IMS and the EMW modules. ACTION: Refer to the following module application charts for the specific vehicle application and location of the different types of modules. NOTE: FOR APPLICATIONS NOT LOSTED IN THE FOLLOWING MODULE APPLICATION CHARTS, THE “CHECK ENGINE” LIGHT IS CONTROLLED BY THE EEC IV PROCESSOR. THESE VEHICLES DO NOT USE THE “EMW” MODULE

Related Content:

1985 honda elite 150 manual, 1986 190e 2 3 crank trigger diagram, GM service manual for1986 camaro pdf, 1986 suncrest motorhome repair manuel, 1985 ford 302 v-8 throttle body, daewoo g25p oil filter, free rair manula for 1986 iroc, how to bypass ignition switch on a 1986 corvette, isuzu dmax manual oil change, netzsch parts manuals

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

0

Filed Under (More Manuals) by admin on 19-05-2012

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

Related Content:

low coolant 01 suburban, how to check radiator fluid level pontiac grand prix, Low coolant light olds intrigue, evap sensor on 2002 suburban, replace low coolent sencor on 1997 chevy lumnia, Low Coolant Sensor Location in olsdmobile silluette, 2002 Chevrolet Impala see a diagram of the a/c controls, p0446 2002 monte carlo, 2002 mercury sable cooling system, 2006 Envoy low idle

Related Content:

emission light on impala, 86 ford ranger emission sensors, 2011 dodge durango not charging, 1992 CHEVrolet silverado idle air control assembly calibration specifications, 1992 Grand Marquis Manual, mazda 3 transmission gear indicator light, service 4wd light on silverado, Isuzu NPR Warning Light Icons, slip light on nissan titan, how to reset washer fluid malibu 06