Skip to content

c6 corvette service manual free download

You search PDF repair manual about c6 corvette service manual free download, if there are search results will appear below. If search results do not exist, please search by others keyword.


FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

Jaguar Electronic Parking Brake Diagnostic Aid/ Repair Manual

INITIAL VISUAL INSPECTION 1. Place the vehicle on a suitable lift. 2. Visually inspect the parking brake cable installation, parking brake caliper levers and general condition of the brakes. • Ensure the caliper levers are returning fully to their stops. • Confirm the cable routing is correct • Confirm that the cable is securely fixed at all abutment points and is free to move within the C-clip. • Where cable routing goes over the top of the stabilizer bar drop links, confirm that the stabilizer bar rubber deflector blocks are fitted, and that the brake cables have not been getting trapped behind the stabilizer bar drop links (look for tell-tale marks on the links and/or cables). NOTE: Global Technical Reference (GTR) lookup sequence is as follows: GTR Home > NAS > Model > Service Information > Model Year > Workshop Manual > 2: Chassis — Section 206: Brake System NOTE: Refer to the correct section by reference to VIN and based on whether the vehicle is fitted with high performance brakes or not. 3. Rectify any obvious faults. 4. If no obvious faults are found or further guidance is needed to rectify faults, please proceed to the next stage of this bulletin. Refer to GTR Sections 206-05 (parking Brake and Actuation) and GTR Section 206-04 (Rear Disc Brake). 5. If any faults were found and rectified, it will be necessary to re-calibrate the parking brake after rectification. See ‘Parking Brake Calibration’ procedure. PREPARE THE PARKING BRAKE FOR DETAILED INSPECTION CAUTION: Jaguar IDS DVD 111 or later and Midtronics PSC-550 Vehicle Power Supply must be connected to the vehicle battery during diagnosis. 1. Install the Midtronics PSC-550 Vehicle Power Supply to the vehicle. 2. Connect the IDS to the vehicle and begin a new diagnostic session by entering the correct VIN for the current vehicle. 3. Follow the IDS prompts to read the vehicle configuration. 4. Select ‘YES’ when prompted ‘Do you wish to read diagnostic trouble codes?’. 5. Follow all on-screen instructions to complete this task. 6. Select ‘Vehicle Configuration’ tab when the ‘Content Model’ is displayed. 7. Select ‘Electronic Parking Brake’. 8. Select ‘Release to Service Position’ (S-TYPE/XJ) or ‘Parking Brake Unjam Procedure’(XK) ‘. CAUTION: When using the special service tool, take care to operate in the ‘release’ direction. Actuator motor damage may result if the tool is operated in the ‘apply’ direction for any length of time). 9. If the parking brake will not release using IDS, use the special service tool to fully release the parking brake. Refer to GTR Section ‘Parking Brake Cable Tension Release’ (in Section 206-05) for details of using the special service tool.


FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Single Speed Axle Service Manual

Figure 1-1 Spicer axles are identified with a manufacturing date and complete part numbers stamped on the right- hand tube. The part number may also appear on a metal tag attached to the cover plate by the cover screws, depending upon the requirements of the vehicle manufacturer. The part number, consisting of six digits reading from left to right, is the basic number for identifying the particular axle assembly. The seventh digit following the dash will identify ratio, differential, and end yoke options used in the assembly. The next group of numbers is the manufacturing date of the axle and is interpreted as follows. The first number is the month, the second number is the day of the month, the third number is the year, the fourth is the line that built the axle, and the letter is the shift. NOTE It is recommended that when referring to the axle, the complete part number and build date be obtained. To do this, it may be necessary to wipe or scrape off dirt, etc., from the axle housing. If the axle is unique on design such that the unit cannot be identified in the standard manner as described above, refer to the vehicle manufacturer’s service and/or parts manual for proper identification. SERVICING COMPONENTS NOT COVERED IN THIS MANUAL Service procedures for some components may not be covered in this manual because they are unique to the vehicle application. Refer to the vehicle manufacturer’s service manual for servicing those components. (e.g. brakes, hubs, rotors, and wheel end components). VEHICLE STORAGE OR PROLONGED INOPERATION If the vehicle has not been operated on a regular daily basis, it is recommended that the vehicle be operated at least once every two weeks. The vehicle should be moved far enough to cause the drivetrain components to make several complete revolutions. This procedure will help assure that all internal components receive adequate amount of lubrication to help reduce component deterioration caused by an undesirable environment (e.g. high humidity).

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.