Skip to content

cadillac deville tcc solenoid

You search PDF repair manual about cadillac deville tcc solenoid, if there are search results will appear below. If search results do not exist, please search by others keyword.

1994 Cadillac DeVille Concours Procedure to Disable Illumination of Service Indicator AFTER the Installation of Passive Struts/Shocks

download
Run a wire from a switched ignition (hot in Run) source to relay pin 85. 1992-1993 Oldsmobile Achieva with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1992-1994 Buick Skylark with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module which is attached to the back side of the right (passenger side) sound insulator panel. Follow the wiring harness up under the dash assembly and then cut and tape the wiring harness. 1993-1996 Buick Park Avenue with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1991-1995 Oldsmobile Ninety Eight with Computer Command Ride (CCR) This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. 1994-1999 Pontiac Bonneville with Computer Command Ride (CCR) The feedback strut/shock assemblies are still available for these vehicles. However, if the customer desires to reduce the repair expense, the following steps may be taken to allow installation of non-feedback assemblies and the disabling of the malfunction indicator lamps. This is a stand alone system. Remove the CCR module, which is located under the carpeting beneath the driver’s seat. Parts Information The following parts are required to make the correction on the 1993 Eldorado/Seville and the 1994-1995 DeVille. Parts are currently available from GMSPO

1992 Cadillac Deville 4.9L Windshield Wiper Blade and Arm REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION Catera Open the hood. 1. Remove the windshield wiper arm stud cap that conceals the nut. 2. Remove the windshield wiper arm nut. 3. Grasp the windshield wiper arm with both hands. 4. Use a rocking motion to loosen the windshield wiper arm from the pivots. 5. Remove the windshield wiper arm and blade. 6. To install: Installation is the reversal of the removal procedure. 7. Deville and Fleetwood WIPER ARM Raise the hood as needed for access to the wiper arms. 1. Operate the wipers and turn the ignition OFF when the wipers are at the mid-wipe position. 2. Lift the wiper arm from the windshield. 3. On 1990 vehicles, pull the retaining latch and remove the arm from the transmission shaft. 4. On 1991-93 vehicles, disengage the retaining latch using a suitable tool and remove the arm from the transmission shaft. 5. To install: Install the wiper arm onto the transmission shaft. 6. Push the retaining latch in and return the arm assembly to the windshield. 7. Park the wipers. If adjustment is necessary, proceed as follows: Remove the right wiper arm. a. Open the small door to access the wiper linkage; refer to the illustration for details. b.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2005 Hyundai Truck Santa Fe TRANSAXLE/ ATA SOLENOID DIAGNOSTIC REPAIR MANUAL

download
Subject: ATA SOLENOID DIAGNOSTIC CODES P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765, P0770 This TSB supersedes TSB # 05-40-006 to include DTC descriptions in Step 10. DESCRIPTION: Incorrect operation of the transaxle solenoids may result in the following three symptoms: REPAIR PROCEDURE: 1. Check Engine Light illuminated 2. Transaxle held in 3rd gear “Fail-safe” 3. Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765 or P0770 set. NOTE: Do NOT replace the transaxle for solenoid codes listed as open/short. Instead, follow the repair procedure shown below. 1. Using a Hi-Scan Pro, check for DTC in both the “Engine” and “Automatic Transaxle” menus. Record the DTC and description. 2. From the Hi-Scan Pro, select: ^”Hyundai Diagnosis” menu ^”Vehicle ^”Auto Transaxle” menu ^”Actuation Test” ^Press the F1 button (STRI) and test the LR, UD, 2ND, OD, DCC and FSV solenoid (if applicable). Monitor the Hi-Scan and listen for a solenoid sound from the engine compartment. ^If Hi-Scan shows: ^”TEST FAILURE” and no solenoid sound is heard, go to Step 3. ^”COMPLETED” and solenoid sound is heard, the wiring between the PCM/TCM has no open or short circuits. Go to Step 5. 3. Visually check the wiring harness between the TCM and transaxle for a damaged wire or a short circuit to ground. Disconnect the connectors to the solenoids at the transaxle and the PCM/TCM and check for a bent pin or a pin not fully inserted into the connector. If so, repair or replace the ECM control harness, P/N 914XX-XXXXX 4. Check the harness inside the transaxle oil pan for a short circuit to ground. Replace the harness if damage is found or if three or more solenoid DTCs are found in Step 1. (Refer to TSB # 04-40-015 for instructions). Zoom Sized for Print 5. Refer to the DTC recorded in Step 1 and follow the repair procedure shown. SOLENOID REPLACEMENT: 6. Remove the battery. 7. Drain the radiator. Remove the lower radiator hose from the radiator. 8. Drain the ATF. 9. Remove the valve body cover from the transaxle

1998 Pontiac Grand Prix DTC P0753 1-2 Shift Solenoid Circuit Electrical Repair Manual

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 6. This step isolates the fault between the engine harness and the transmission harness. 8. This step verifies that circuit 1222 is neither open nor shorted to power. 11. This step verifies that the 1-2 shift solenoid has neither shorted across its windings nor increased its resistance. DTC P0753 1-2 Shift Solenoid Circuit– Electrical Step Action Value(s) Yes No 1 Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Install the Scan Tool . 2. Turn the ignition switch to the RUN position. Important Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. 3. Record the DTC Freeze Frame and Failure Records, then clear the DTC. — Go to Are DTCs P0758, P1860 or P0740 set? Step 3 Go to Step 6 3 1. Remove the TCC fuse. 2. Inspect the fuse for an open. Was a condition found and corrected? — Go to Step 4 Go to Step 5 4 Repair short to ground in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 5 Repair the open in engine harness circuit 1339 or transmission harness circuit 839. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 — 6 1. Turn the ignition switch OFF. 2. Disconnect the Automatic Transmission 7-way connector. 3. Install the J 38835 Transmission Electrical Jumper on the engine harness connector. 4. Connect a test lamp from terminal E to terminal A of the jumper using a J 35616-A Connector Test Adapter Kit. Important Additional DTCs will set. 5. With the engine OFF, turn the ignition ON. Is the test lamp ON? — Go to Step 7 Go to Step 8 7 Inspect engine harness circuit 1222 for a short to ground. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 20 8 Using the scan tool command the 1-2 solenoid ON and OFF three times. Does the test lamp cycle ON and OFF as commanded? — Go to Step 11 Go to Step 9 9 Inspect engine harness circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 10 10 Inspect engine harness circuit 1222 for a short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found and corrected? — Go to Step 21 Go to Step 19 11 1. Turn the ignition OFF. 2. Disconnect the J 38835 Transmission Electrical Jumper from the engine harness. 3. Connect the J 38835 Transmission Electrical Jumper to the Automatic Transmission 7-way connector. 4. Connect a J 39200 Digital Multimeter (DMM) from 19 ohms to 31 ohms terminal E to terminal A of the jumper. Is the measured resistance within the specified range? Go to Step 15 Go to Step 12 12 Is the resistance greater than the specified value? 31 ohms Go to Step 13 Go to Step 15 13 Inspect the transmission harness RED wire circuit 839 and the LT GRN wire circuit 1222 for an open. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 14 Go to Step 18 14 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 15 Connect the J 39200 Digital Multimeter from terminal A of the jumper to ground. Is the resistance less than the specified value? 100 ohms Go to Step 16 Go to Step 18 16 Inspect the transmission harness LT GRN wire circuit 1222 for a short to ground or short to power. Refer to General Electrical Diagnosis Procedures . Was a condition found? — Go to Step 17 Go to Step 18 17 Replace the Automatic Transmission Wiring Harness. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 18 Replace the 1-2 Shift Solenoid Valve Assembly. Refer to Solenoids and Wiring Harness Replacement . Is the replacement complete? — Go to Step 21 — 19 Inspect PCM connector C1 (Blue) for bent, damaged or backed out connector pins. Was a condition found and corrected? — Go to Step 21 Go to Step 20 20 Replace the PCM. Refer to PCM Replacement/Programming . Is the replacement complete? — Go to Step 21 — 21 In order to verify your repair, perform the following procedure: 1. Using the scan tool, clear DTCs. 2. Operate the vehicle under the following conditions: { The engine speed is more than 500 RPM. { The vehicle is not in fuel shut off. { System voltage is 10-16 volts. { Drive the vehicle through the 1-2 shift. { When the 1-2 SS Valve Assembly is commanded ON, the voltage decreases to zero. { When the 1-2 SS Valve Assembly is commanded OFF, the voltage increases to B+. { All conditions are met for 5 seconds.