caliper torque on 2008 impala

You search PDF repair manual about caliper torque on 2008 impala, if there are search results will appear below. If search results do not exist, please search by others keyword.



  caliper torque on 2008 impala Direct Download speed 5432 Kb/s

  caliper torque on 2008 impala Full Version speed 8172 Kb/s



2004 Chrysler Pacifica DISC BRAKE SHOES Removal And Installation Manual

0

Filed Under (Chrysler Manuals) by admin on 13-05-2011

download
DISC BRAKE SHOES Removal (Front) 1. Remove master cylinder fluid reservoir cap. 2. Raise and support vehicle. 3. Remove tire and wheel assembly. 4. Place appropriately sized C-clamp over brake caliper, placing screw-drive head against outboard shoe and hook against rear of caliper. Slowly tighten screw-drive retracting caliper pistons into bores and brake outboard brake shoe free from caliper fingers. See Fig. 22 . Remove C-clamp. 5. Once outboard shoe is free from caliper fingers, slide caliper inboard on guides providing clearance between the rotor and inboard brake shoe. 6. Slide an appropriate prying tool through center opening in top of caliper behind brake shoe between 2 caliper pistons. Use care not to come in contact with pistons or dust boots potentially damaging them. Pry against rear of inboard brake shoe braking it free from caliper pistons. 7. Remove the 2 brake caliper guide pin bolts. See Fig. 23 . 8. Remove disc brake caliper from brake adapter and hang out of way using wire or a bungee cord. Use care not to overextend brake hose when doing this. 9. Remove brake shoes from disc brake caliper adapter. See Fig. 27 . 10. Install master cylinder fluid reservoir cap. 2. Install disc brake caliper over brake shoes on brake caliper adapter. See CALIPER . 3. Align guide pin bolt holes with guide pins and install caliper guide pin bolts. See TORQUE SPECIFICATIONS . 4. Install tire and wheel assembly. See TORQUE SPECIFICATIONS . 5. Lower vehicle. 6. Pump brake pedal several times to seat shoes to caliper and brake rotor. 7. Check and fill brake fluid level as necessary. See CHECKING & FILLING under BRAKE FLUID in SERVICE. 8. Road test vehicle making several stops to wear off any foreign material on brakes and to seat brake shoes. Removal (Rear) 1. Raise and support vehicle. 2. Remove both rear tire assemblies from vehicle. 3. Remove 2 caliper guide pin bolts. 4. Remove the 2 caliper guide pin bolts. See Fig. 24 . 5. Remove caliper from caliper adapter. See CALIPER . 6. Remove outboard brake shoe by pushing shoe away from caliper fingers, dislocating locating pins built into shoe backing plate from holes in caliper fingers, then sliding brake shoe down and off of brake caliper. See Fig. 28 . 7. Pull inboard brake shoe away from caliper piston, dislocating retaining clip from cavity in piston. Remove inboard shoe. NOTE: In some cases, it may be necessary to retract caliper piston in its bore a small amount in order to provide sufficient clearance between shoes and rotor to easily remove caliper from knuckle. This can usually be accomplished before guide pin bolts are removed, but grasping rear of caliper and pulling outward working with guide pins, thus retracting piston. DO NOT push on piston directly as it may get damaged.

Related Content:

4L80E Troubleshooting Guide, bench bleeding brake mc 97 ford ranger pdf, www motorcraftservice com owners guide, 2006 honda accord brake caliper torque, v reader repair, lucerne brake caliper torque spec, Mazda 6 Shop Manual PDF, proper torque for chevy truck pitman arm replacement 2004 avalanche, rear brake caliper removal on 2010 ford f-150, replacing caliper pin 2007 sienna

2008 Ford Taurus AWD V6-3.5L – Rear Brake Pads Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-06-2012

download
Removal WARNING: Do not use any fluid other than clean brake fluid meeting manufacturer’s specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury. WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. CAUTION: Do not allow the brake fluid to come in contact with the adhesive backing on the brake pads. If brake fluid is spilled onto the brake pads, new pads must be installed. CAUTION: Use only specified brake parts cleaner. Use of other cleaners may leave a residue on the brake caliper preventing the brake pads adhesive surface from bonding with the brake caliper. 1. Remove the wheel and tire. 2. Check the brake fluid level in the brake fluid reservoir. * If required, remove fluid until the brake master cylinder reservoir is half full. 3. Remove the brake caliper bolts. 4. CAUTION: Do not use the brake caliper sight hole to retract the pistons as this may damage the pistons and boots. CAUTION: Do not allow the caliper to hang from the brake hose or damage to the hose may occur. CAUTION: Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever. Carefully position the caliper aside using a suitable support or damage to the parking brake cable end fittings may occur. Using hand force and a rocking motion, separate the brake caliper from the anchor plate. Position the brake caliper aside. * Support the caliper with mechanic’s wire. 5. CAUTION: When the brake pads are separated from the brake caliper , new brake pads must be installed to prevent brake noise. The brake pads are one-time use only. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. 6. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed. Inspect the brake caliper anchor plate assembly. * Check the guide pins and boots for binding or damage. * Install a new brake caliper anchor plate if it is worn or damaged. Installation 1. NOTE: To move the piston back into the caliper, the LH piston is turned clockwise and the RH piston is turned counterclockwise. NOTE: A moderate to heavy force toward the caliper piston must be applied. If sufficient force is not applied, the internal park brake mechanism clutch cone will not engage and the piston will not compress. Using the special tool (or equivalent such as OTC tool 7317A), compress the brake caliper piston into its cylinder. 2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. 3. CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface or damage to components may occur. Do not install contaminated pads. NOTE: Install all the new hardware supplied with brake pad kit. Install the new spring clips and brake pads. 4. Position the brake caliper and install the 2 bolts. * Tighten to 29 Nm (21 lb-ft). 5. If necessary, fill the brake fluid reservoir with clean, specified brake fluid. 6. With the vehicle engine running, apply 89-133 N (20-30 lb) of pressure on the brakes for approximately one minute, to make sure the brake pads adhere to the caliper before any contamination can be introduced. 7. Test the brakes for normal operation.

Related Content:

diagram of a 2004 chev thoe break line sysetm, stoplightswitch1997surburban, isuzu npr brake booster removal instruction, front brake line diagram on 2004 tahoe, isuzu npr brake adjustment, 2002 ford ranger brake bleeding procedure, hummer h3 brake job, rear disk brake assembly on 2000 Saturn, repair manual for toyota yaris brakes, brake line diagram for 96 buick regal

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, 2008 checrolet colorodo emmisions purge valve, how to change the thermostat 2008 ford escape ehow, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 pilot alternator replacement, Kia Spectra Repair Manual PDF, 2008 f250 haynes pdf, hummer h3 2008 p0741, 2008 toyota tundra tailgate latch assembly

2004 Ford Expedition/ Navigator Brake Pads REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-06-2012

download
Removal 5. NOTE: Verify if the anchor housing spring has 1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination. 4. CAUTION: If the anchor housing spring is to be reused, do not force the anchor housing spring off the brake caliper. Do not install a damaged anchor housing spring. Remove the anchor housing spring. REMOVAL AND INSTALLATION (Continued) 6. Rotate the spring upward then remove it from the brake caliper. 9. NOTE: Do not allow the brake caliper to hang from the brake hose. Remove the brake caliper. 7. NOTE: On the RH side, the anchor housing 1 Remove the zero-drag spring. spring must be installed with the 2-tabbed end in the lower brake caliper cavity. The 2 Remove and discard the brake illustration below shows the anchor housing caliper-to-anchor plate bolts, guide pins and spring end with 2 tabs. boots. For RH brake caliper, release the upper portion of the anchor housing spring. •Apply force at the center of the anchor housing spring and pull outward at the top of the anchor housing spring to remove it from the upper brake caliper cavity. 10. Remove the brake pads from the brake caliper. 11. NOTE: Use a wood block or used brake pad to protect the brake caliper piston boots. Compress the brake caliper pistons. 8. Rotate the spring downward then remove it from the brake caliper.

Related Content:

toyata vios caliper spring clips

2004 Ford Expedition/ Navigator Brake Pads REMOVAL AND INSTALLATION

0

Filed Under (Ford Manuals) by admin on 26-01-2011

download
1. CAUTION: Install a new lining if worn 1 end with 2 tabs. If yes, the LH side anchor to or past the specified thickness above the housing spring must be installed with the metal backing plate or rivets. Install new 2-tabbed end in the upper brake caliper cavity. pads in complete axle sets. For the LH brake caliper, release the lower If necessary, using a suitable suction device, portion of the anchor housing spring. remove the brake fluid in the master cylinder •Apply force at the center of the anchor reservoir until it is half filled. housing spring and pull outward at the bottom of the anchor housing spring to 2. Remove the wheel and tire assembly. For remove it from the lower brake caliper additional information, refer to Section 204-04. cavity. 3. Inspect the brake pads for wear or contamination. 4. CAUTION: If the anchor housing spring is to be reused, do not force the anchor housing spring off the brake caliper. Do not install a damaged anchor housing spring. Remove the anchor housing spring. REMOVAL AND INSTALLATION (Continued) 6. Rotate the spring upward then remove it from the brake caliper. 9. NOTE: Do not allow the brake caliper to hang from the brake hose. Remove the brake caliper. 7. NOTE: On the RH side, the anchor housing 1 Remove the zero-drag spring. spring must be installed with the 2-tabbed end in the lower brake caliper cavity. The 2 Remove and discard the brake illustration below shows the anchor housing caliper-to-anchor plate bolts, guide pins and spring end with 2 tabs. boots. For RH brake caliper, release the upper portion of the anchor housing spring. •Apply force at the center of the anchor housing spring and pull outward at the top of the anchor housing spring to remove it from the upper brake caliper cavity. 10. Remove the brake pads from the brake caliper. 11. NOTE: Use a wood block or used brake pad to protect the brake caliper piston boots. Compress the brake caliper pistons. 8. Rotate the spring downward then remove it from the brake caliper.

Related Content:

installing break pads on 2004 exped

1995 Mazda MX-6 FRONT DISC BRAKE PADS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mazda Manuals) by admin on 16-02-2012

download
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope. 2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See MINIMUM PAD LINING SPECIFICATIONS (FRONT) table. 3. To install, reverse removal procedure. Use Disc Brake Expander (49-0221-600C) and an old pad to push piston fully inward to install disc pads. Fig. 2: Exploded View Of Front Brake Disc Assembly Courtesy of MAZDA MOTORS CORP. MINIMUM PAD LINING SPECIFICATIONS (FRONT) Application Thickness In. (mm) MX-6, 626 FRONT DISC BRAKE CALIPER Removal & Installation Raise and support front of vehicle. Remove front wheel assemblies and disconnect brake hose. Plug all openings. Remove front disc brake pads. See FRONT DISC BRAKE PADS . Remove remaining mounting bolt(s). Remove caliper from vehicle. To install, reverse removal procedure. Bleed air from system. FRONT BRAKE ROTOR Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove front disc brake caliper with brake hose connected. See FRONT DISC BRAKE CALIPER . Wire caliper aside. Remove rotor-to-hub screws (if equipped). Remove rotor. 2. Machine rotor if lateral runout exceeds specification. Replace rotor if measured thickness is less than specified minimum thickness. See DISC BRAKE SPECIFICATIONS table. To install, reverse removal procedure. REAR DISC BRAKE PADS Removal & Installation 1. Raise and support rear of vehicle. Remove rear wheel assemblies. Release parking brake and disconnect parking brake cable from caliper. Remove manual adjustment gear concealment plug from caliper. See Fig. 3 . Insert an appropriate size Allen wrench through hole and turn manual adjustment gear counterclockwise to retract caliper piston. 2. Remove upper guide bolt from caliper. Rotate caliper downward and support using wire. Remove “M” springs. Remove pads, shims and guide plates. Replace pad if lining thickness is less than .04″ (1.0 mm). 3. To install, reverse removal procedure. Turn manual adjustment gear clockwise until brake pads slightly touch rotor. Turn manual adjustment gear back 1/3 turn.

Related Content:

2007 chevy tahoe min disc thickness after machining, 95 chevy monte carle front brake rotor minimum thickness, Minimum Rotor Thickness Spec Sheet, pontiac pursuit parking brake cable, minuem roter tickness, minimum rotor thickness for chrysler pacifica, min spec for 2008 mada brake rotor thickness, mimimum rotor thickness for a 2000 chrysler sebring, mazda 626 pin size brake pads, how do i replace the rear brake caliper guide pin on a 2005 kia spectra

2003 Honda Accord LX REAR DISC BRAKE PADS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 31-05-2011

download
Removal Raise and support vehicle. Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward. If you are reusing pads, install in original position. Rotate caliper piston clockwise into cylinder, then align cutout in piston with tab on inner pad by turning piston back. See Fig. 15 . 2. Lubricate boot with rubber grease to avoid twisting. If boot is twisted, back it out and position properly. Install brake caliper. Install and torque caliper bolts to proper specification. See TORQUE SPECIFICATIONS . Install brake hose onto suspension arm with mounting bolt. After installation, check for leaks. Pump brake pedal several times to seat pads. Bleed brakes as necessary. See BLEEDING BRAKE SYSTEM . WARNING: Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health. Avoid breathing dust particles. NEVER use an air hose or brush to clean brush assembly. Use an OSHA-approved vacuum cleaner. NOTE: Engagement of brake may require a greater pedal stroke immediately after brake pads have been replaced as a set. Several applications of brake pedal will restore normal pedal stroke.

Related Content:

brake torque specs for 2007 honda accord, honda accord rear brake pad retainer, torque specs 2008 accord rear brakes

2007 Volkswagen Rabbit BRAKES Brake System removing and installing

0

Filed Under (Volkswagen Manuals) by admin on 18-01-2012

download
Fig. 49: Torque Wrench V.A.G 1331 Courtesy of VOLKSWAGEN UNITED STATES, INC. * Torque wrench V.A.G 1331 Fig. 50: Piston Resetting Tool T10145 Courtesy of VOLKSWAGEN UNITED STATES, INC. * Piston resetting tool T 10145 Brake pads, removing When removing, mark brake pads that will be used again. Install in the same position, otherwise braking effect will be uneven! * Remove wheels. Fig. 51: Locating Brake Wear Pad Indicator Connector Courtesy of VOLKSWAGEN UNITED STATES, INC. * Disconnect connector – 1 – for brake pad wear indicator. Fig. 52: Protective Caps Courtesy of VOLKSWAGEN UNITED STATES, INC. * Remove caps – arrows -. Fig. 53: Removing/Installing Brake Caliper Guide Pins Courtesy of VOLKSWAGEN UNITED STATES, INC. * Loosen both guide pins – arrows – and remove from brake caliper. * Remove brake caliper and secure with wire so that the weight of the brake caliper does not burden or damage the brake hose. * Remove brake pads from brake caliper. Cleaning: * Thoroughly clean contact surfaces for brake pads at brake carrier, remove corrosion. * Clean brake caliper. Use only appropriate solvents for cleaning brake caliper. Brake pads, installing Before pressing piston into cylinder using piston resetting tool, brake fluid must be extracted from brake fluid reservoir. Otherwise, especially if reservoir has been topped off, fluid will overflow and cause damage. Fig. 55: Identifying Brake Pad Retaining Springs Courtesy of VOLKSWAGEN UNITED STATES, INC. * Insert inner brake pad (piston side) – 1 – and outer brake pad – 2 – with retaining springs into brake caliper. * Inner brake pad (piston side) with large three-finger clip – 1 -. * Outer brake pad with small three-finger clip – 2 – (colored black). Fig. 56: Identifying Lower Part Of Brake Caliper Housing Courtesy of VOLKSWAGEN UNITED STATES, INC. * Place brake caliper with brake pads on brake carrier first at bottom – arrow

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, cummins n14 oil pan bolt torque, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, oil pan bolt torque specs on cummins n-14, n14 connecting rod torque, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques

2003 Volvo XC90 2.5T L5-2.5L Turbo Brake Pad Service and Repair Manual

0

Filed Under (Volvo Manuals) by admin on 12-06-2012

download
Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove:
2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 3 Clean and check the brake caliper and dust cover. Clean and check the brake pad mating surfaces in the brake caliper and caliper holder. Check piston dust boot. NOTE: If the dust boot is damaged dirt may have penetrated the cylinder. If this is the case the caliper must be replaced. Checking the brake disc Check brake disc friction surfaces. If the brake disc displays signs of out-of-true, check its lateral run out. Replace the brake disc if it displays signs of heavy wear, variable thickness or similar. NOTE: Minimum disc thickness/replacement limit = 18.0 mm . Minimum recommended disc thickness when installing new brake pads = 18.7 mm . Installation Installing the brake pads

Related Content:

volvo xc90 2 5t turbo, 2009 scion xb rear pad replacement, 20020 envoy how to replace brake dustshield, repairing the turbo on a 2001 volvo s40, f53 brake replacement, tools needed to change brakes on 2008 pontiac torrent, change brake pads 2008 scion, cavalier 2003 service manual, 2003 volvo v40 headlight screws manual, 2005 4runner brake rotor removal

Related Content:

4L80E Troubleshooting Guide, bench bleeding brake mc 97 ford ranger pdf, www motorcraftservice com owners guide, 2006 honda accord brake caliper torque, v reader repair, lucerne brake caliper torque spec, Mazda 6 Shop Manual PDF, proper torque for chevy truck pitman arm replacement 2004 avalanche, rear brake caliper removal on 2010 ford f-150, replacing caliper pin 2007 sienna