cat 3406 flywheel bolt torque

You search PDF repair manual about cat 3406 flywheel bolt torque, if there are search results will appear below. If search results do not exist, please search by others keyword.



  cat 3406 flywheel bolt torque Direct Download speed 5432 Kb/s

  cat 3406 flywheel bolt torque Full Version speed 8172 Kb/s



1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs for 5 7 volvo penta exhaust manifold, torque specs 4 8 chevrolet, rod torque botyom end n14, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

2001 Toyota Echo Transmission and Drivetrain Removal And Installation Manual

0

Filed Under (Toyota Manuals) by admin on 10-03-2012

download
REMOVAL 1. REMOVE HOOD HINT: At the time of installation, please refer to the following item. Adjust the hood. 2. REMOVE WIPER ARM HINT: At the time of installation, please refer to the following item. Adjust the installation position of the wiper arms 3. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS 4. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 nuts and No. 2 cylinder head cover. Torque: 7.0 Nm (71 kgf-cm, 62 inch lbs.) 5. REMOVE BATTERY AND AIR CLEANER CASE ASSEMBLY WITH AIR HOSE 6. DISCONNECT WIRE HARNESS FROM TRANSAXLE Remove the set bolt of the wire harness clamp. 7. DISCONNECT CONTROL CABLE a. Remove the 2 clips and washers. b. Remove the 2 clips and disconnect the control cables from the transaxle. 8. DISCONNECT CLUTCH RELEASE CYLINDER a. Remove the set bolt of the clutch line. Torque: 4.9 Nm (50 kgf-cm, 43 inch lbs.) b. Remove the 2 set bolts of the clutch release cylinder. Torque: 12 Nm (120 kgf-cm, 9 ft. lbs.) 9. DISCONNECT GROUND CABLE Remove the set bolt of the ground cable from the engine left mounting bracket. 10. DISCONNECT BACK-UP LIGHT SWITCH AND VEHICLE SPEED SENSOR CONNECTORS 11. REMOVE 2 TRANSAXLE UPPER SIDE MOUNTING BOLTS Torque: 33 Nm (340 kgf-cm, 25 ft. lbs.) 12. REMOVE STARTER SET BOLT Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 13. ATTACH ENGINE SLING DEVICE TO ENGINE HANGER Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print a. Remove the bolt. b. Install the 2 No. 1 engine hangers with the bolts in the correct direction. Parts No.: No. 1 engine hanger: 12281-21010 Bolt: 91642-81025 Torque: 40 Nm (400 kgf-cm, 29 ft. lbs.) c. Attach the engine chain hoist to the engine hangers. CAUTION: Do not attempt to hang the engine by hooking the chain to any other part. 14. RAISE VEHICLE CAUTION: Make sure that the vehicle is securely supported. 15. REMOVE LH ENGINE UNDER COVER 16. DRAIN TRANSAXLE OIL Oil grade: API GL-4 or GL-5 Viscosity: SAE 75W-90 Capacity: 1.9 liters (2.0 US qts, 1.7 Imp. qts) Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.) 17. REMOVE RH AND LH FRONT DRIVE SHAFTS 18. REMOVE SUSPENSION MEMBER a. Remove the 2 set nuts and bolt of the engine rear mounting insulator from the suspension member. b. Disconnect the sliding yoke. c. Power steering: Disconnect the pressure feed and return tubes. d. Power steering: Disconnect the tube clamp

Related Content:

torque clutch converter solenoid problems 2001 isuzu rodeo, 2004 chevy tahoe 5 3 air conditioner belt tensioner bolt torque specs, 2006 nissan navara d40 cylinder head bolt tightening, how to adjust clutch pedal on toyota echo

1999 Honda Civic EX TORQUE SPECIFICATIONS

0

Filed Under (Honda Manuals) by admin on 04-02-2012

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Related Content:

pontiac vibe head torque secuensia, 1999 honda civic door bolt torque specifications, tork settings for fd 42 engine, nuts&bolts service, j35 honda bolt pattern transmission, how to rebuild a saturn 1 9 sohc, honda generator bolt torque spec, head bolt torque specifications 2000 buick century, fd42 manifold gasket, D16y8 cam removal sequence

2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, torque number sway bar ends 2002 lincoln ls, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques, how many foot lbs torque on lower control arm bolt lincoln ls, ford e450 wheel torque, ford 4 0 sohc oil pan inserts torque specs, cummins N 14 rod torque

FORD E450 CUTAWAY OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the front and rear bolts from the leaf spring. 2. Remove existing U-bolts and U-bolt plate that attach the axle to the leaf spring . Remove the leaf spring from the axle. 3. Remove the front spring hanger bracket , rear leaf spring hanger bracket, and any overload spring brackets . See Figure 2-1. These can be removed by grinding, or air chiseling, the heads off the factory-installed rivets, and using a hammer and punch to remove remainder of the rivet. See Figure 2-2. 3. Remove the OEM shock absorbers and retain the lower mounting fastener for later use. 4. Cut the exhaust as it bends downward after the axle, at its most vertical and straight section. See Figures 2-3 & 2-4. Save the cut-off portion for use in Section 9. Remove the rear exhaust hanger from the frame. CAUTION: Be careful that the leaf spring does not spring out of its hanger, or off the frame. FIG. 2-4 FIG. 2-1 FRONT HANGER BRACKET FIG. 2-2 LEAF SPRING REAR HANGER BRACKET FIG. 2-3 CUT HERE FOR EXHAUST MODIFICATION 6 3. DRIVER SIDE ASSEMBLY 1. Review Figure 3-1 & Figure 11-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using the (4) 7/16 x 1 1/4 UNC FLANGE BOLTS and (4) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . 3. Loosely secure the suspension Arm to the axle using (2) 5/8 UNF, 4.0 X 10.50 U-bolts, (4) 5/8 WASHERS, (4) 5/8 UNF HIGH NUTS, and the Arm Mount Plate. Make sure the locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. Note : Install the axle tube spacer between the U-bolts and Axle when installing on an E350. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the Arm to the Front Hangar using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Using the enclosed bolt hole template for the Upper Air Spring Mount, align the template to the frame using the appropriate rear spring hanger holes. Mark and drill three (3) new frame holes to 0.47″ on each side of the frame. Bolt the air spring bracket assembly to the frame using (5) 7/16 x 1 1/4 UNC CAPTIVE BOLTS and (5) 7/16 UNC TOP LOCK FLANGE NUTS. (See Table 11-1 for appropriate Torque) . Note : Use the correct holes designated for either the E350 or E450 chassis. See Figure 3-2. 6. Bolt the air spring to the suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut. (See Table 11-1 for appropriate Torque) . FIG. 3-2 E450 HOLE PATTERN E350 HOLE PATTERN TEMPLATE OE REAR HANGER MOUNT HOLES FRAME FIG. 3-1 AIR SPRING ARM MOUNT PLATE AXLE TUBE SPACER WEAR WASHER TRAILING ARM U-BOLT FRONT HANGER BRACKET AIR SPRING MOUNT BRACKET 7 AFTER BOTH SIDES HAVE BEEN INSTALLED (Sections 4, 5, 6) FINISH THE FOLLOWING STEPS: 7. Tighten the Arm bushing bolts and the Arm U-bolts AFTER the suspension has been installed and brought to Design Height, in Section 9.5. (See Table 11-1 for appropriate Torque) . 8. Install the new shock absorbers using the same orientation as factory, with factory and enclosed hardware. 9. IMPORTANT: Route the brake cable away from the air spring and any other moving components. It may need to be tied, or slightly repositioned in order to accommodate this. 4. PASSENGER SIDE DISASSEMBLY 1. Repeat Section 2 for the passenger’s side of the truck. 5. PASSENGER SIDE ASSEMBLY 1. Repeat Section 3 for the passenger’s side of the truck. Double-check all fasteners for proper torque. Check all clearance points and all alignments. See Figure 5-1 for details.

Related Content:

2002 rondevious change rear spring, f150 1995 changing front leaf spring brackets, head bolts torque on 2001 2 5 ford ranger, how to replace 2000 chevy cavalier exhaust bracket, how to replace mazda 3 rear coil springs, is there a metal washer before e clip on pitman arm seal gearbox on a 1997 ford f150, tie rod end at pitman armnut torque 2000 f350 7 3l 4wd, Trailing Arm bracket for 2000 Buick Century

Toyota Starlet Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 15-01-2012

download
Removal Removal Raise and support front of vehicle. 1. Support engine. 2. Remove: RH front wheel. Inner wing panel. Engine mounting and bracket. Auxiliary drive belt(s). Cylinder head cover. Timing belt upper cover [1] . 3. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure crankshaft pulley timing mark aligned [2] . 4. Check hole in camshaft sprocket aligned with mark on camshaft bearing cap [3] . 5. If not: Turn crankshaft one turn clockwise. 6. Remove: Crankshaft pulley bolt [4] . Use tool Nos.09213-14010 & 09330-00021. Crankshaft pulley [5] . Use tool No.09213-31021. Timing belt lower cover [6] . 7. Temporarily fit crankshaft pulley bolt [4] . 8. Ensure timing marks aligned [3] & [7] . 9. Slacken tensioner bolt [8] . Move tensioner away from belt and lightly tighten bolt. 10. Remove: Timing belt. Tensioner pulley and spring [9] & [10] . 11. Installation Installation Check tensioner pulley for smooth operation [9] . 1. Check free length of tensioner spring is 38,4 mm [10] . 2. Fit tensioner and spring. Ensure spring is connected correctly. 3. Push tensioner to left and lightly tighten bolt [8] . 4. Ensure timing marks aligned [3] & [7] . 5. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 6. Slacken tensioner bolt [8] . 7. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [3] & [7] . 8. If not: Repeat installation and tensioning procedures. 9. Tighten tensioner bolt [8] . Tightening torque: 19 Nm. 10. Remove crankshaft pulley bolt [4] . 11. Install: Timing belt lower cover [6] . Crankshaft pulley [5] . 12. Install components in reverse order of removal. 13. Tighten crankshaft pulley bolt [4] . Tightening torque: 152 Nm. Use tool Nos.09213-14010 & 09330-00021. 14.

Related Content:

1999 toyota camry crankshaft bolt direction, can I replace the camshaft pulley bolt on a 2004 Kia Sorento here at home?

1997 Jeep Cherokee 2WD Serpentine Belt INSPECTION ADJUSTMENT REMOVAL And INSTALLATION

0

Filed Under (Jeep Manuals) by admin on 05-01-2012

download
INSPECTION When inspecting serpentine drive belts, small cracks that run across the ribbed surface of the belt from rib to rib are considered normal. If the the cracks are running along the rib (rather across), this is not normal and the belt(s) must be replaced. ADJUSTMENT It is not necessary to adjust belt tension on the 5.2L or 5.9L engines and on the 2.5L and 4.0L engines (without power steering). These engines are equipped with an automatic tensioner. The tensioner maintains correct tension at all times. 2.5L and 4.0L Engines With Power Steering See Figures 1, 2, 3 and 4 If the vehicle is not equipped with power steering, it will be equipped with an idler pulley. If equipped with an idler pulley, refer to and follow the 5.2L/5.9L belt removal and installation procedure. Loosen the pump upper pivot bolt, lower locknut and pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 1. Use a belt tension gauge placed in the middle of the belt being tested. Proper tension for a new belt is 180-200 lbs. (800-900 N) and 140-160 lbs. (623-712 N) for a used belt. 2. Tighten the pump adjusting bolt to achieve proper tension and recheck the belt tension. 3. Fig. Fig. 1: Loosen the pivot bolt (1), then the locking bolt (2) to loosen the power steering pump from behind Fig. Fig. 2: Use a ratchet and 13mm size socket to rotate the power steering pump Fig. Fig. 3: Adjustment points on the 2.5L engines without power steering (rear view) Fig. Fig. 4: Adjustment points on the 2.5L engine (front view) Removal & Installation 2.5L and 4.0L Engines With Power Steering See Figures 5, 6 and 7 Fig. Fig. 5: Proper belt routing diagram can usually be found on a sticker located in the engine compartment Fig. Fig. 6: Common 4.0L engine serpentine belt routing Fig. Fig. 7: Common 2.5L engine serpentine belt routing Loosen the rear power steering pump mounting bolts using a ratchet and 13mm socket or a 13mm box wrench. 1. Loosen the pump upper pivot bolt, lower locknut and the pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 2. Remove the belt. 3. To install: Install the belt. 4. Tighten the pump adjusting bolt to achieve proper tension. 5. Install the pump rear mounting bolts, pivot bolt and locknut. Tighten the bolts to 20. ft. lbs. (27 Nm). 6. Check the belt for proper tension. If tension is incorrect, refer to the adjustment procedure in this section. 7. 5.2L and 5.9L Engines See Figures 8, 9 and 10

Related Content:

1986 jeep cherokee serpentine belt route, serpintin belt diagram for 2006 jetta, kia 3 5 crank bolt for sale, jetta 2006 fan belt totation, GM 10 Bolt Rebuild Manual, gm 10 bolt instructions, 99 Jeep Cherokee Owners Manual pdf, 2010 Kia Forte Serpentine Routing Belt Diagram, 2004 honda civic serpentine belt, 1995 Jeep 2 5L ccv orfice and emissions

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

0

Filed Under (More Manuals) by admin on 22-06-2012

download
1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.

Related Content:

4efe maf sensor, 4L60E VSS Sensor Location, b0091 front end sensor 3 location, cat 3406 e engine sensor locations, front end connector sensor 1

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, montero crank shaft pully removal, montero xls bleeding cooling system how, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero

Honda Civic A/C Compressor Belt Adjustment

0

Filed Under (Honda Manuals) by admin on 21-11-2011

download
1. Apply a force of 98 N (10 kgf, 22 Ibf), and measure the deflection between the A/C compressor and the crankshaft pulley. A/C Compressor Belt Used Belt: B16A2 engine 6.0 – 9.5 mm (0.24 – 0.37 in) 7.5 – 9.5 mm (0.30 – 0.37 in) 4.5 – 6.5 mm (0.18 – 0.26 in) 5.0 – 6.5 mm (0.20 – 0.26 in) Except B16A2 engine New Belt: B16A2 engine Except B16A2 engine Note these items when adjusting belt tension: If there are cracks or any damage evident on the belt, replace it with a new one. ” Used belt ” means a belt which has been used for five minutes or more. ” New belt ” means a belt which has been used for less than five minutes. 2. Loosen, the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Turn the adjusting bolt to get proper belt tension. Retighten the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Recheck the deflection of the A/C compressor belt. 3. 4. 5. Tension Gauge Method 1. Attach the special tool to the 4/C compressor belt as shown below, and measure the tension of the belt. A/C Compressor Belt Used Belt: B16A2 engine 390 – 540 N (40 – 55 kgf, 88 – 120 Ibf) Except B16A2 engine 340 – 490 N 135 – 50 kgf, 77 – 110 Ibf) New Belt: B16A2 engine 740 – 880 N (75 – 90 kgf, 170 – 200 Ibf) Except B16A2 engine 690 – 830 N (70 – 85 kgf, 150 – 190 Ibf) Note these items when adjusting belt tension: Follow the manufacturer’s instructions for the belt tension gauge. If there are cracks or any damage evident on the belt, replace it with a new one. ” Used belt ” means a belt which has been used for five minutes or more. ” New belt ” means a belt which has been used for less than five minutes. 2. Loosen the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Turn the adjusting bolt to get proper belt tension. Retighten the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Recheck the tension of the 4/C compressor belt

Related Content:

2003 kia sedona belt tensioner lock nut, drive belt routing diagrams 2012 kia optima, why does ac compressor lock up on 98 honda civic

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs for 5 7 volvo penta exhaust manifold, torque specs 4 8 chevrolet, rod torque botyom end n14, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs