Skip to content

changing fresh air door actuator on 2008 chevy impala

You search PDF repair manual about changing fresh air door actuator on 2008 chevy impala, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.

2008 TOYOTA RAV4 DOOR SILL ENHANCEMENT REPAIR MANUAL

download
1. Check Kit Content. (a) Check kit for content and damage. (Fig. 1-1) 2. Apply tape. (a) Using the factory door sill plate as a guide, apply tape to the door sill surface at each end of the sill plate as shown. (Fig. 2-1) 3. Remove Factory Door Sill Plates. (a) Using an NRT, Lift the edge of the factory sill plate. (Fig. 3-1) (b) Once the edge of the sill plate has been lifted the plate may be removed by hand by pulling firmly upward. Be sure not to damage the weather strip in the process. (c) Discard the factory door sill plate. Fig. 2-1 Fig. TOYOTA RAV4 2008 – DOOR SILL ENHANCEMENT Procedure Page 3 of 5 pages Issue: A 12/3/07 4. Installation Preparation. (a) Thoroughly clean all installation surfaces. (i) Use a clean lint free cloth. (ii) Clean surface thoroughly using VDC approved cleaner and wipe dry Do allow cleaner to air dry. (Fig. 4-1) (b) Ensure door sill enhancement to be between 70 F and 110 F at time of installation. (c) Ensure vehicle surfaces to be between 70 F and 110 F at time of installation. (d) Do not touch or allow debris or contaminates to come in contact with the adhesive backing before installation. (e) Inspect parts prior to installation. Dry fit parts for alignment reference. 5. Install Front Door Sill Enhancements. (a) Check Part Number label on back of door sill enhancement for applicable side of vehicle, Right Hand or Left Hand and Front or Rear. (b) Position part over vehicle door sill area to check for proper fit and orientation prior to installation. NOTE: The vehicle name logo on the door sill enhancement must be oriented as to be read from the outside of the vehicle. (c) Remove the tape liner from the door sill enhancement. Do not touch the adhesive

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

2008 HONDA ACCORD 4-DOOR BACK-UP SENSOR INSTALLATION INSTRUCTIONS

download
INSTALLATION NOTE: When installing a back-up sensor and a trailer hitch, install the back-up sensor before installing the trailer hitch. 1. Make sure you have the anti-theft code for the radio and navigation system (if equipped), then write down the radio presets. 2. Disconnect the negative cable from the battery 3. Remove the two caps from the rear bumper, and remove the rear bumper (two bolts, six self-tapping screws, and two clips). NOTE: Have an assistant help you when removing and installing the rear bumper. 4. Remove the trunk floor mat (one clip). 6D26050E CLIPS 2 CAPS REAR BUMPER 6 SELF-TAPPING SCREWS 7109070E CLIP TRUNK FLOOR MAT 5. Remove the rear trunk trim panel (four clips and three hooks). Remove the trunk left side trim panel (five clips). 8. Remove the left rear speaker cover (nine retaining tabs). 710908AE LEFT TRUNK SIDE TRIM PANEL 3 CLIPS 2 CLIPS 7115030E LEFT REAR SPEAKER COVER 9 RETAINING TABS 9. Remove the left rear speaker (one bolt and disconnect the vehicle connector). 10. Attach the control unit bracket to the control unit 11. By hand, thread the 6 mm flange nut onto the control unit bracket stud. Insert the control unit bracket into the hole in the vehicle panel as shown. Secure the bracket to the vehicle panel. VEHICLE PANEL CONTROL UNIT CONTROL UNIT BRACKET HOLE 6 mm FLANGE NUT HOLE CONTROL UNIT BRACKET

2008 HONDA ACCORD 2- AND 4-DOOR AUTOMATIC DAY/NIGHT MIRROR (LX) INSTALLATION INSTRUCTIONS

download
INSTALLATION 1. Make sure you have the anti-theft code for the radio, then write down radio station presets. 2. Disconnect the negative cable from the battery. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 7214110E AUTOMATIC DAY/NIGHT MIRROR AUTOMATIC DAY/NIGHT MIRROR HARNESS 3. Disengage the eight retaining tabs and remove the left and right lenses from the roof console. Without Moonroof: With Moonroof: 7302010B ROOF CONSOLE RIGHT LENS 4 RETAINING TABS LEFT LENS 4 RETAINING TABS SHOP TOWEL FLAT-TIP SCREWDRIVER 761802AB ROOF CONSOLE RIGHT LENS 4 RETAINING TABS LEFT LENS 4 RETAINING TABS SHOP TOWEL FLAT-TIP SCREWDRIVER Open the sunglass holder. 5. Remove the four screws (two black and two silver) and let the roof console drop down. Disconnect the vehicle connectors and remove the roof console. Without Moonroof: With Moonroof: 730202AB BLACK SCREWS ROOF CONSOLE SUNGLASS HOLDER (Open. ) SILVER SCREWS VEHICLE CONNECTORS 761803AB ROOF CONSOLE SUNGLASS HOLDER (Open. ) VEHICLE CONNECTORS BLACK SCREWS SILVER SCREWS 6. Turn the sunvisor holder 45°, and remove the two sunvisor holders. 7. Turn the left sunvisor toward the driver’s seat. 8. Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.