Skip to content

changing valve cover gasket on 2003 sport trac

You search PDF repair manual about changing valve cover gasket on 2003 sport trac, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003-2005 FORD Explorer Sport Trac Alignment – Irregular Front Tire Wear SERVICE PROCEDURE

download
ISSUE Some 2003-2005 Explorer Sport Trac vehicles equipped with the Goodyear Wrangler RT/S, P255/70R16 109S AT OWL tire, may exhibit signs of feathering heel-toe wear on the inside or outside edges of the front tires . Tire noise may also be present during regular highway drive or when braking. ACTION Inspect the tires for feathering heel-toe wear. It may be necessary to rotate or replace tires and reset toe. Refer to the following Service Procedure. SERVICE PROCEDURE Zoom Sized for Print 1. Visually inspect the front tire’s inside and outside shoulder ribs (Figure 1) 2. Measure the difference in tread depth of the leading edge compared to trailing edge, of the most-worn lug (figure 2). If the average difference in tread depth between leading and trailing edge is less than 2 mm, rotate the tires . If the average difference is more than 2 mm, replace the front tires. Also inspect the rear tires and replace if necessary. 3. Ensure that the camber and caster readings are within specification

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

2002 Ford Lincoln LS Valve Cover LH Workshop Manual

download
Valve Cover LH Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 3. Remove the air cleaner housing. 1. Disconnect the mass air flow (MAF) sensor electrical connector. 2. Remove the bolt. 3. Remove the housing. 4. CAUTION: To disconnect the Norma fitting, squeeze the tabs and pull straight out or damage to the fitting can occur. Disconnect the crankcase ventilation tube. 5. Disconnect the fuel hose. For additional information, refer to Section 310-00 . 6. Disconnect the evaporative emission canister purge valve hose. 7. Remove the vapor management valve (VMV) cover. SECTION 303-01B: Engine — 3.9L 2002 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/17/2001 Material Item Specification 8. Remove the VMV. 1. Disconnect the vacuum hose. 2. Disconnect the purge hose. 3. Disconnect the electrical connector and the push pin. 4. Remove the nuts and the valve. 9. Remove the exhaust gas recirculation (EGR) vacuum regulator solenoid. 1. Disconnect the electrical connector. 2. Remove the screws and the EGR vacuum regulator solenoid. 10. Remove the bracket. 1. Remove the hose. 2. Remove the bracket. 11. Position the engine wiring harness up. 12. Remove the ignition coil cover. * Inspect the gasket and install a new gasket as necessary.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2002 Ford Explorer Sport/ Sport Trac Cylinder Head Removal and installation manual

download
Removal Both cylinder heads 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information , refer to Section 100-02 . 2. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Drain the cooling system. For additional information, refer to Section 303-03 . 4. Remove the intake manifold. For additional information, refer to Intake Manifold in this section. 5. Remove the cooling fan shroud. For additional information, refer to Section 303-03 . 6. Remove the accessory drive belt. For additional information, refer to Section 303-05 7. Remove the LH valve cover. For additional information, refer to Valve Cover — LH in this section. 8. Remove the RH valve cover. For additional information, refer to Valve Cover — RH in this section. 9. Disconnect the generator electrical connections. 10. Remove the accessory drive belt tensioner. 11. Remove the bolts and the generator and generator mounting bracket as an assembly. 12. Disconnect the crankshaft position (CKP) sensor electrical connector. 13. Disconnect the wiring harness retainers. 14. Disconnect the water temperature indicator sender unit and the engine coolant temperature (ECT) sensor electrical connectors. 15. Disconnect the exhaust gas recirculation (EGR) tube fitting. 16. Remove the upper heater coolant hose. 1. Squeeze the heater hose clamp. 2. Remove the heater coolant hose. 17. Remove the lower heater coolant hose and position aside. 1. Remove the bolt. 2. Squeeze the hose clamp. 3. Remove the heater coolant hose and position aside. 18. NOTE: The coolant hose will be removed with the thermostat housing. Move the coolant bypass hose clamp off the water pump outlet. 19. Remove the bolts, the thermostat housing and the bypass hose. 20. Remove the bolt and detach the wiring harness retainer. 21. Remove the bolts and position the accessory drive bracket aside.22. Detach the wiring harness retainer. 23. Remove the bolt and the oil level indicator tube. 24. Using the special tool, disconnect the LH spark plug wires from the spark plugs. 25. Disconnect the fuel pulse damper vacuum connector. 26. Remove the four bolts and position the fuel supply tube aside. 27. Remove the bolts and the fuel rail and injectors as an assembly.28. NOTE: Mark each of the roller followers to make sure it is installed in its original position during reassembly. Use the special tool to remove the roller followers. 29. Remove the lower radiator hose. 30. Remove the nut and position the A/C tube bracket aside. 31. Using the special tool, set the No. 1 piston at top dead center (TDC). RH cylinder head 32. Remove the RH fenderwell splash shield. 33. Remove the RH camshaft chain tensioner.