Skip to content

chevrolet 5 3 engine diagram

You search PDF repair manual about chevrolet 5 3 engine diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

1968-1972 Chevrolet Chevelle LS1/ LS2 engine swap Installation Manual

download
These headers have been designed and tested to directly fit a retrofit GM LS series engine in a 1968-1972 Chevrolet Chevelle with automatic transmission and stock front suspension/steering components. If you are attempting to install these headers on a vehicle with aftermarket steering or suspension parts you may need to modify some parts for proper fitment. We also guarantee these headers will properly fit up to the matching Bassani Power X crossover and aft-cat listed for this car on bassani. com or in our catalog. Installation instructions: 1.) Remove existing exhaust manifolds or headers if present. 2.) Lubricate included fasteners with anti-seize compound and install headers with gaskets onto engine through engine compartment. 3.) Torque bolts evenly to approximately 18 ft. lbs. 4.) Apply anti-seize to supplied collector studs and install the short threaded end into tabs on header collectors. 5.) Attach remaining exhaust components as desired. 6.) Check torque on fasteners after the first 100 miles and then again at 500 miles

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination