Skip to content

chevrolet 5 3 oil flow diagrams

You search PDF repair manual about chevrolet 5 3 oil flow diagrams, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

2002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement Manual

download
Radiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air baffle to the vehicle. Tilt the rear of the air baffle upward slightly. Position the upper clip of the air baffle to the lower edge of the front fascia support C-channel. 2. Slide the baffle towards the front of the vehicle in order to completely engage the upper and lower clips of the baffle onto the fascia support. 3. Align the tabs at the rear of the air baffle to the openings in the upper radiator support. 4. Install the radiator air baffle retainers.

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.