chevy sway bar bushing torque specs

You search PDF repair manual about chevy sway bar bushing torque specs, if there are search results will appear below. If search results do not exist, please search by others keyword.



  chevy sway bar bushing torque specs Direct Download speed 5432 Kb/s

  chevy sway bar bushing torque specs Full Version speed 8172 Kb/s



2004-2008 FORD F150 FRONT LEVELING SYSTEM INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 19-12-2011

download
Front End Installation: 1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the p sides of the vehicle. Next remove the wheel from both sides. assenger s 2. Remove the upper strut mounts with a 15-mm wrench or . m socket. Using a ball cket. Use an socket. You will need a socket to remove the far strut mount 3. Remove the sway bar lower link pin bolt from the bottom of the control arm with an 18 mm socket. 4. Disconnect the tie rod end with a 21 m peen hammer or impact tool, hit the steering knuckle (not the tie rod) until the tie rod pops out. If you use a tie rod pickle fork, be careful not to cut the tie rod boot. A severed tie rod boot will allow dirt and moisture to damage the tie rod end. 5. Remove the upper ball joint nut with a 21 mm so impact tool or ball peen hammer and hit the steering knuckle until the upper control arm pops out.
6. Support the knuckle with a bungee cord or safety wire so not to overextend the CV axel or stretch the brake hydraulic hose. 7. Next remove the struts lower bolt. Using a 27 mm wrench, hold the nut and remove the bolt with a 30 mm socket. 8. Remove the strut assembly. 9. Place the strut extension on the top of the strut, hold the part up to start the nuts onto the factory studs. ** Caution: Use the factory nuts with the factory studs** 10. Run down nuts snug with end wrench. Torque to OEM specs. 11. Place strut back into upper strut mount. Tighten provided nuts snug with wrench or ratchet (after install, you will torque to OEM specs). 12. Use a pry bar to position the lower control arm and the strut mount to reinstall the mounting bolt. Torque to OEM specs. 13. Place a jack under the lower control arm. Raise the lower control arm to reattach the ball joint. A pry bar may be used to hold the upper control arm into position. Torque the ball joint nut to OEM specs. 14. Reattach the tie rod end. Torque to OEM specs. 15. Reattach the sway bar. Torque to OEM specs. 16. Reattach the wheel. Torque to OEM specs. 17. Repeat on opposite side. 18. Lower vehicle to ground and torque strut mounts to OEM specs. 19. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques, how many foot lbs torque on lower control arm bolt lincoln ls, ford e450 wheel torque, ford 4 0 sohc oil pan inserts torque specs

2007-2008 TOYOTA FJ CRUISER 2WD AND 4WD 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 12-11-2011

download
4Runner/FJ Cruiser Installation Instructions 08/28/08 INST-431.DOC Page 2 of 5 FRONT OF 4RUNNER/FJ CRUISER 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Before lifting vehicle, remove rear shock absorbers and discard. 5. Jack up the vehicle from the lift point in Figure A. 6. Support the vehicle with jack stands from the points in Figure A. 7. Remove the front wheels. 8. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 9. Remove front skid plate using 12mm socket. 10. Remove sway bar from frame using 14mm socket. See Figure C. 11. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 12. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 13. Remove the three nuts (14mm) from the top of the strut. See Figure D. 14. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 15. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 16. Release the compressor. 17. Remove the spring top plate from the strut. 18. Remove and discard the rubber spacer FRONT OF 4RUNNER/FJ CRUISER (continued) 19. Remove (hammer) the studs from the spring top plate. See Figure “F.” 20. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 21. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 22. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 23. Install the TOP OUT EXTENDER over the STUDS (Figure H). 24. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 25. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 26. Reinstall tie rod ends, torque to spec. 27. Reinstall sway bar to frame. 28. Reinstall sway bar end links into spindles. Torque to spec. 29. Reinstall front skid plate. 30. Replace the wheels; torque to spec.

Related Content:

Volvo D13 engine bolt torques, 2002 PT Cruiser jacking points, 92 toyota pinion nut torque spec, dtc molykote, how to remove torque converter bolts from a Volvo D13, removal of front struts Toyota FJ cruiser

1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs 04 gmc yukon, torque specs 4 8 chevrolet, torque specs for 5 7 volvo penta exhaust manifold, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

2005-2008 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 2 of 7 FRONT OF TACOMA 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure A. 5. Support the vehicle with jack stands from the points in Figure A. 6. Remove the front wheels. 7. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 8. Remove front skid plate using 12mm socket. 9. Remove sway bar from frame using 14mm socket. See Figure C. 10. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 11. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 12. Remove the three nuts (14mm) from the top of the strut. See Figure D. 13. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 14. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 15. Release the compressor. 16. Remove the spring top plate from the strut. 17. Remove and discard the rubber spacer Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 3 of 7 FRONT OF TACOMA (continued) 18. Remove (hammer) the studs from the spring top plate. See Figure “F.” 19. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 20. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 21. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 22. Install the TOP OUT EXTENDER over the STUDS (Figure H). 23. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 24. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 25. Reinstall tie rod ends, torque to spec. 26. Reinstall sway bar to frame. 27. Reinstall sway bar end links into spindles. Torque to spec

Related Content:

2005 tacoma shop manual free download, install rack and pinion 2006 tacoma, pdf how to replace 2003 prerunner steering knuckle, rack and pinion 99toyota tacoma install, skid plate install intructions for a 2014 toyota tacoma, torque specs for pressure plate 1997 tacoma 4x4, toyota avensis jacking points, toyota tacoma frame replacement procedures

TOYOTA MATRIX 2WD / COROLLA / PONTIAC VIBE SPORT SWAY BAR SET INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-11-2011

download
INSTALLATION OF HOTCHKIS FRONT SWAY BAR 1) Securely block the rear wheels of the vehicle. Use a jack to lift up the front of the vehicle and use jack stands to support it. Do not remove the front wheels during installation for safety. 2) Use a 14mm wrench and 6mm Allen wrench to remove the nuts holding the end links to the ends of the stock sway bar. Remove the end links from the ends of the sway bar. Retain the hard ware for later use.
3) Use a 19mm Wrench or socket to remove the four bolts mounting the cradle to the sub frame. Retain the bolts for later re-installation. 4) Use a 14mm socket or wrench to remove the two nuts and three bolts holding the lower engine mount to the cradle. Retain the hardware for later re-installation. 5) Use a 14mm wrench or socket to remove the three bolts holding the front of the cradle assembly to the radiator support. Retain the hardware for later re-installation. 6) Use a 17mm wrench or socket to remove the four bolts holding the steering rack to the cradle. Retain the hardware for later re-installation. 7) With all the bolts removed the cradle should droop loosely enough to reach the sway bar mounted to the top rear portion of the cradle. Use a 12mm socket or wrench to loosen and remove the four bolts holding the stock sway bar in place. Remove the stock sway bar, bushings and brackets. Retain the stock hardware for later re-installation

Related Content:

how to repair 2003 kia sedona rear swaybar links, 1999 oldsmobile intrigue sway bar, How Much Should It Cost To replace sway bars on 2002 Lincoln LS, how to remove rear sway bar leanks 2006 dodge dakota, how to replace stabilizer bushings on saturn vue 2003, Replacing front sway bar bushings on 2009 ram 1500, sway bar for 1999 oldsmobile intrude, What size Allen wrench do I need to take off the not for the swaybar link on 2004 Chevy trailblazer, you tube video of changing 2006 f150 sway bar

1984-2002 Pontiac Camaro / Firebird ADJUSTABLE TORQUE ARM INSTALLATION MANUAL

0

Filed Under (Pontiac Manuals) by admin on 23-02-2012

download
Inspect the motor mounts and the transmission mount. Worn, weak or broken mounts will cause the torque arm to not function properly and can cause damage to your vehicle. Stock OE transmission mounts in Camaros and Firebirds are very weak and known to fail. If you have a broken or weak transmission mount, it will cause the torque arm to actually lift the tail end of the trans. up. This could cause severe wheel hop, driveline misalignment and possible damage to the transmission, drive shaft, u-joints, rear axle, torque arm, and/or floor pan of vehicle. We highly recommend using a good quality polyurethane transmission mount like Energy Suspension #33- 1108. Using the Energy Suspension transmission mount is good insurance that your transmission stay solid and the torque arm will work to its full potential. 2. Inspect the rear suspension bushings. We strongly recommend using either Edelbrock (#5274) lower trailing arms with a spherical ball on one end and polyurethane bushings on the other, Edelbrock (#5204) trailing arms with polyurethane bushings on both ends, or other high quality trailing arms that use high quality polyurethane bushings. We also recommend the use of an Edelbrock or other high quality panhard rod to replace the stock OE piece that uses sponge rubber bushings. The lower trailing arms and panhard rod secure the rear axle under the car. Upgrading to stronger high quality tubular trailing arms and panhard rod with polyurethane bushings will increase the overall strength, eliminate the sponge feel of rubber bushings and further increase the function potential of the torque arm. Worn out trailing arm or panhard rod bushings can contribute to or cause torque arm or other suspension component failures. Remember each suspension component

Related Content:

2008 CHEVY UPLANDER TRAIL ARM BUSHINGS, how to change rear bushing in 06 chevy uplander, mistubishi fuso 4d34 idle linkage, torque on pitman arm 99 crown vic

1979-1985 Toyota 4×4 3, 5, 7″ Suspension Lift Installation Manual

0

Filed Under (Toyota Manuals) by admin on 17-03-2012

download
1. Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is unlevel (side-to-side) from the factory, but usually not noticed until a lift kit has been installed which makes the difference more visible. Using a measuring tape, measure the front and rear (both sides) from the ground up to the center of the fender opening above the axle. Record below for future reference. (Note: Due to OEM inconsistency and the available options, the amount of lift gained by this lift kit can vary as much as 1/2″.) Driver Side: Frt______ Rear______, Passenger Side: Frt________ Rear________ 2. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of new springs. Now apply a thin coat of grease on outside of bushings. On SYSTEMS with new rear springs, insert steel sleeve into rear spring eye. Rear spring eye is on the long end of the spring. To Install Front: 3. Raise front of vehicle and support securely with jack stands under the frame behind front spring shackle and block the rear wheels. Remove the tires, shocks, and u-bolts. Care should be taken when removing the front u-bolts because they will be re-used on 3″ kits, not on 3″ SYSTEMS. (Caution: The front axle will now be free to move, so support securely on floor jack.) 4. Remove the anti-sway bar bolts. Remember the arrangement of the rubber bushings and washers. Loosen; do not remove, the bolt attaching the track bar eye to the bracket on the driver’s side of the front axle. This will allow the front axle to drop down easier. (When installing a 7″ kit, remove and discard the anti-sway bar.) 5. With a floor jack supporting the front axle, unbolt each end of front leaf springs and remove from both sides. Install new springs as follows: part #T303S springs can be installed with either end toward front; part #T305S and #T307S must be installed with the thick end of bottom degree shim toward the front of vehicle. (Note: Do NOT tighten spring eye bolts at this time.) Using the floor jack, raise the front axle up to leaf springs. Be sure tie bolts align and fit down into the tie bolt holes in the axle housing. Install front u-bolts. 6. On 3″ and 5″ kits bolt up sway bar using the longer bolts and spacer tubes provided, and using original bushings and washers. Do not over tighten making the bushings bulge or crack. Tighten track bar bolt. (See Photo #1). 7. On 7″ kits remove track bar bolt from bracket on driver’s side of front axle. Install new track bar bracket onto the original bracket with the included bolts and nuts. Attach

1995-2004 TOYOTA TACOMA 4 X 4 AND PRERUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 29-02-2012

download
Tacoma 4WD & PreRunner Installation Instructions Page 3 of 7 09/09/08 INST-425F.DOC FRONT OF VEHICLE 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure “A.” 5. Support the vehicle with jack stands from the points in Figure “A.” 6. Remove the front wheels. 7. Remove the nut (14mm) and the hardware from the anti-sway bar. See Figure “B.” 8. Remove the nut (19mm) and bolt (14mm) from the bottom of the strut. See Figure “C.” 9. Remove the three nuts (14mm) from the top of the strut. See Figure “D.” 10. Remove the strut from the vehicle. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 11. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft in Figure “E.” 12. Release the compressor. 13. Remove the spring top plate from the strut. 14. Remove and discard the rubber spacer. 15. Remove (hammer) the studs from the spring top plate. See Figure “F.” 16. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 17. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring. See Figure “H.” 18. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Figure “E”). (Torque specs can be found on page 1.) 19. Install the TOP OUT EXTENDER over the STUDS (Figure “H”). 20. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 21. When properly installed, PRELOAD SPACER relief and Revtek Industries logo should face outward. (Figure R) 22. Reinstall hardware and nut on anti-sway bar; torque to spec. 23. Replace the wheels; torque to spec.

Related Content:

TORQUESPECLINCOLN2000

1996-2004 TOYOTA TACOMA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 96-04 Tacoma 11/07 5. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the provided strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 6. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the provided spacer the strut will be rotated 180° when reinstalled. 7. Place strut back into the upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 8. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. HINT: It may be helpful to use a pry bar to press down on the steering knuckle for reinstalling the mounting bolt. 9. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 10. Repeat Steps 2 through 9 on the opposite side of the vehicle. 11. Reattach the wheels. Torque to OEM specs. 12. Lower vehicle to the ground and torque strut mounts to OEM specs. 13. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2013 TACOMA OEM SUBWOOFER, how to use oem ball joint press, OEM Ball Joint Press Instructions, 1996 Isuzu NPR Specs

2007 Toyota Tundra PRO STEP INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-05-2011

download
2 Side Bar Kit – Kit 84801 Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3176. 4. Special tools needed: a. 17/64″ drill bit 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Engine Compartment 1. Disconnect both battery cables. Disconnect negative cable first, then positive cable. 2. Factory Side Bars a. Remove factory side bars if present. NOTE Kit parts are prefaced by the word kit and appear in bold print. NOTE If parts are missing from kit, please be prepared to provide the following information: 1. Name of purchase location 2. Bar Code on side of box 3. Date above bar code 4. Date inside box cover 5. Inspector # from inside box cover Positive Cable Negative Cable Prepare to Install Kit Drivers Side of Vehicle 1. Install kit brackets (body mounted). a. Install two kit brackets (body mounted) along driver side of vehicle using either two factory installed bolts per bracket,.or kit supplied 8mm bolts b. Repeat previous step on pass. side of vehicle. 2. Side Bars a. Insert kit sleeve into kit side bar (rear). Install kit bolt (7/16″ x 1″) and kit washer (7/16 USS flat) into kit sleeve . Underside of Body Kit Bracket Kit Side Bar (front) Short End Kit Side Bar (rear) Long End Side Bar (Passenger Side) Kit Sleeve 3 Side Bar Kit – Kit 84801 b. Install kit side bar (front) onto kit sleeve . Install kit bolt (7/16″ x 1″) and kit washer (3/8 USS flat) into kit sleeve . Install Side Bars on Vehicle 1. Install steps on vehicle a. Install the kit side bar assembly (driver) onto kit body brackets using four kit bolts (1/2″ X 1-1/ 4″), four kit washers (1/2″ flat), four kit sleeves (7/8″ OD), and four kit nuts (flange). Install the kit bolts into the outer holes in the kit body brackets . DO NOT TIGHTEN. NOTE The side bar can be installed in two positions. It can be installed so that the steps are flat or it can be installed with the steps slightly angled downward. Kit bolt (7/16″ x 1″), Kit Washer (3/8 USS flat ) Kit Body Bracket Outer Holes Kit Bolts (1/2 X1-1/4″) b. Determine desired position for the steps. Install four kit bolt (7/16″ x 3 1/2″), four kit washers (7/ 16″), and four kit nuts (flange nut) as indicated below. c. Tighten all mounting bolts on driver side of vehi- cle. d. Repeat for passenger side of vehicle. Install Step Pads on Side Bar 1. Step Pads a. Position kit step pads on center of kit side bar hoop . Ensure the kit step pad is level and mark two locations on each pad to drill

Related Content:

rear camber kit instruction for 07 impala, owners manual for 1983 kit roadranger, vacuum windshield wiper model a ford kit repair, delphi alternator rebuild kit, 2006 ford taurus flex pipe repair kit, blend door chevy uplander, repair helicoil for 5 4 liter ford, 2000 blazer frame replacement, installation of Fog Light Assembly 2011 Camry, install cargo net 2014 impala

Related Content:

2000 ford ranger transmission bolt torque specs, torgue spec on 2004 mazda3, 02 ford explorer driveworks front wheel hub torque, torque number sway bar ends 2002 lincoln ls, LOWER CONTROL ARMS TORQUE SPECS ON 2004 PACIFICA, lincoln ls 3 9l connecting rod bearing torque, idler arm torques, how many foot lbs torque on lower control arm bolt lincoln ls, ford e450 wheel torque, ford 4 0 sohc oil pan inserts torque specs