Skip to content

chevy cavalier 2003 hydraulic clutch line

You search PDF repair manual about chevy cavalier 2003 hydraulic clutch line, if there are search results will appear below. If search results do not exist, please search by others keyword.

1996 Ford Bronco/F-Series Clutch Hydraulic Line REMOVAL AND INSTALLATION MANUAL

download
Clutch Hydraulic Line Removal 1. Note the routing of the clutch slave cylinder to clutch master cylinder tube (7A512) line from clutch master cylinder (7A543) to the clutch slave cylinder. 2. Remove retainer pin from clutch master cylinder holding clutch slave cylinder to clutch master cylinder tube in place. 3. Raise the vehicle and install suitable safety stands. 4. Disconnect clutch slave cylinder to clutch master cylinder tube from external clutch slave cylinder. On vehicles equipped with concentric clutch slave cylinders, remove tube using Clutch Coupling Tool T88T-70522-A. Installation 1. Follow the removal procedures in reverse order. 2. Bleed system. Refer to appropriate clutch hydraulic system bleeding procedure in the Adjustments portion of this section.

1996 Ford Bronco/ F-Series Clutch Hydraulic Line REMOVAL AND INSTALLATION MANUAL

download
Clutch Hydraulic Line Removal 1. Note the routing of the clutch slave cylinder to clutch master cylinder tube (7A512) line from clutch master cylinder (7A543) to the clutch slave cylinder. 2. Remove retainer pin from clutch master cylinder holding clutch slave cylinder to clutch master cylinder tube in place. 3. Raise the vehicle and install suitable safety stands. 4. Disconnect clutch slave cylinder to clutch master cylinder tube from external clutch slave cylinder. On vehicles equipped with concentric clutch slave cylinders, remove tube using Clutch Coupling Tool T88T-70522-A. Installation 1. Follow the removal procedures in reverse order. 2. Bleed system. Refer to appropriate clutch hydraulic system bleeding procedure in the Adjustments portion of this section. Hydraulic Clutch Control System, 4.9L, 5.0L and 5.8L Gasoline Engines with Mazda R2 and S5-47 ZF Light-Duty and 7.3L and 7.5L S5-47 ZF Heavy-Duty Transmissions

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

TOYOTA TO CHEVY AND BUICK ENGINE – TURBO CHARGED INSTALLATION INSTRUCTIONS

download
INSTALLATION INSTRUCTIONS: 1. Install the pilot bushing into the engine crank. 2. Bolt the flywheel to the engine crank using special flywheel bolts. 3. Assemble the clutch assembly and special disc to the flywheel using special clutch bolts. 4. Assemble the clutch release arm to the inside ball pivot of the bellhousing. 5. Bolt the slave cylinder to the outside of the bellhousing. 6. Test fit the bellhousing assembly over the clutch assembly and onto the engine block. 7. Place the N1430 release bearing onto the clutch arm fork. 8. Adjust the length of the slave cylinder push rod to a length that provides a minimum of 1/8″ clearance between the release bearing face and clutch fingers. 9. This test fit over the clutch assembly is primarily done for establishing the push rod length. If this procedure is eliminated, you will not have any visual inspection for verifying the push rod adjustment. 10. Remove the bellhousing assembly from the engine. 11. Bolt the bellhousing to the front of your Toyota 5 speed transmission using the original bolts. Make sure that the two dowel pins installed in the face of the 5 speed transmission are properly fitted to the Advance Adapter bellhousing. 12. Slide the new release bearing onto the Toyota bearing retainer. Make sure that there is grease in the internal cavity of the release bearing. Most new bearings are pre-lubricated. 13. With all the components in position, you can now bolt the new bellhousing assembly onto the engine block. We have provided six (6) new socket head bolts, 3/8″-16 x 1-1/2″ long for this purpose. Make sure the engine dowel pins are properly aligned with the new bellhousing dowel pin holes. DO NOT FORCE THE BELLHOUSING ONTO THE ENGINE BLOCK. Some applications may require the tip of the input shaft to be modified slightly. The bellhousing must fit evenly to the engine block. 14. With the bellhousing now in position and the slave cylinder push rod installed, you should be able to verify the clearance between the release bearing & clutch fingers. The lever should have movement of approximately 1/8″ to 1/4″. CAUTION : If you have too much clearance, you will be utilizing too much of the slave cylinder stroke and could possibly prevent you from obtaining a full clutch release. A light duty return spring attached to the clutch release arm will prevent any premature contact of the release bearing with the clutch fingers. 15. The Toyota Land Cruiser slave cylinder will replace the original Toyota slave cylinder. The Toyota truck hydraulic slave cylinder line will have exactly the same fitting size as used on the Land Cruiser slave cylinder. 16. With the new slave cylinder installed, you can now bleed the slave cylinder installation by pumping up the slave cylinder pedal. Most installations are compatible with the original Toyota master cylinder. We have encountered a few installations that require changing of the Toyota master cylinder to a smaller 3/4″ piston. If you have any type of clutch difficulty related to full disengagement of the clutch assembly, contact Advance Adapters for any updated information.

1997 Mercedes Benz SL 500 Hydraulic Cylinder For Soft Top Bow Removal And Installation Manual

download
NOTE: It is necessary to plug the hydraulic lines immediately with plugs 129 589 91 07 and the connections with plugs 129 589 00 91 11. Hydraulic cylinder remove on main bracket from inside of vehicle and lay down in soft top compartment (fig. 8) Hydraulic lines on hydraulic cylinder remove (fig. 8) NOTE: Plug the hydraulic lines immediately with plugs 129 589 00 91 07, the connections on the distributors and hydraulic cylinders with plugs 129 589 00 91 11. Screws screw out (fig. 8, item 8) and remove limit switch (item 9) from hydraulic cylinder NOTE: Check limit switches after completing vehicle and adjust, if required. Reinstall in opposite order (observe installation note) Check for proper function and leakage Special too Installation note When installing the hydraulic cylinder pay attention to the code numbers on hydraulic lines as well as the position of the lines in the B-pillar. Line positioning and code numbers Removal & Installation of Hydraulic Cylinder For Top Actuation Notes Removal & Installation of Hydraulic Cylinder For Top Actuation Preliminary jobs: Remove coupe roof (operating instructions). Remove baggage shelf. See: Interior Moulding / Trim\Service and Repair Remove coverings in rear. Remove occasional seats. See: Seats\Service and Repair