Skip to content

chevy hhr evap sensor how to replace

You search PDF repair manual about chevy hhr evap sensor how to replace, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

1997 Chevrolet Chevy K Pickup DTC P0152 HO2S Circuit High Voltage Bank 2 Sensor 1 Repair Manual

download
The number below refers to the step number on the diagnostic table. 2. This test determines if the conditions exist in order to set the DTC P0152. 3. If the HO2S (Bank 2, Sensor 1) is intrnally shorted, the HO2S (Bank 2, Sensor 1) voltage displayed on a scan tool will be over 1.0 volt (1000 mV). Important: Before clearing DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. This data will be lost when the Clear DTC Information function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Connect the scan tool. 2. Run the engine at the normal operating temperature. 3. Place the vehicle in park or neutral. 4. Apply the parking brake. 5. Increase the engine speed to the specified value. Does the scan tool data display indicate HO2S sensor voltage fixed above the specified value? 1200 RPM 0.976 V (976 mV) Go to Step 3 Go to Step 4 3 1. Disconnect the HO2S. 2. Turn on the ignition while leaving the engine OFF. 3. Turn ON the ignition leaving the engine off. Does the scan tool data display indicate the HO2S voltage near the specified value? 400 mV) Go to Step 6 Go to Step 5 4 The DTC is intermittent. Are any additional DTCs set? — Go to the applicable DTC table Go to Diagnostic Aids 5 1. Check for a short to voltage in the HO2S Signal circuit. 2. If a problem is found, repair the circuit as necessary. Refer to Wiring Repairs in Electrical Diagnosis. Was the HO2S Signal circuit shorted? — Go to Step 8 Go to Step 7 6 Replace the HO2S. Refer to Heated Oxygen Sensor (HO2S) Replacement . Is the action complete? — Go to Step 8 — 7 Replace the VCM. Important: When replacing the VCM, the new VCM will need to be programed. Refer to VCM Replacement/Programming . Is the action complete? — Go to Step 8 — 1. Use the scan tool in order to select the DTC and the Clear DTC Information functions.

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall Service Procedure

download
Why is your vehicle being recalled? Your vehicle may have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. If this happens while the vehicle is moving, a crash could result without prior warning. What will we do? Your GM dealer will replace the crankshaft position sensor. This service will be performed for you at no charge . Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual service correction time of approximately one hour and twenty minutes. What should you do? You should contact your GM dealer to arrange a service appointment as soon as possible. Bring the enclosed customer reply form with you when you visit your dealer. The form identifies the repairs required. If you no longer own this vehicle, please let us know by completing the form and mailing it back to us. Did you already pay for this repair? The enclosed form explains what reimbursement is available and how to request reimbursement if you have paid for repairs for the recall condition.

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

3406E Truck Engine Installation OR Removal Of The Speed/ Timing Sensor

download
1. Disconnect the speed/timing connector “P9/J9″ (2) . Inspect the connector for the following conditions. * Corrosion * Bent pins * Missing pins * Damaged sockets * Mismating * Broken wires 2. Remove the Speed/timing sensor (1) from the front gear cover. 3. Examine the plastic end of the sensor for signs of wear or contaminants such as metal filings. The plastic end of the speed/timing sensor should have no contaminants and should show no wear (greater than 0.051 mm (0.0020 inch) from the face) . 4. Use a screwdriver to carefully pry the plastic sensor end to the fully extended position (approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor). 5. Gently push in on the plastic end of the sensor. The plastic end should be firm. The plastic end should resist movement in the retract direction. If there is no resistance replace the sensor 6. Remove the two bolts (3) and remove the cover (5) from the flywheel housing. This hole is used for engine turning. 7. Put one bolt (3) in the timing bolt location (4) . The timing bolt location is approximately 127 mm to 152 mm (5 inch to 6 inch) above the hole in the flywheel housing for engine turning. I 8. Use 9S-9082 Engine Turning Tool (6) and a 1/2 inch drive ratchet wrench to turn the engine flywheel in the direction of normal engine rotation. The normal engine rotation is in a counterclockwise direction when viewed from the flywheel end. Turn the engine flywheel until the timing bolt engages with the threaded hole in the flywheel. Note: Visually check the location of the tooth on the wheel on which the speed/timing sensor is to be positioned. The end of the sensor must be in alignment with a tooth on the wheel and not in alignment with the valley of the wheel. Note: The No. 1 piston must be at either top center of the compression stroke or at top center of the exhaust stroke. 9. Inspect the speed/timing sensor before installation. Use steps 3 through step 6 to inspect the sensor. 10. If the sensor end is not fully extended, use a screwdriver to carefully pry the plastic sensor end to the fully EXTENDED position approximately 4.775 mm (0.1880 inch) beyond the metal housing of the sensor.