Skip to content

chillton diagram 1999 ford ranger evap solenoid

You search PDF repair manual about chillton diagram 1999 ford ranger evap solenoid, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 FORD EXPLORER/ RANGER TRANSMISSION-4R44E OR 5R55E-SLIPPING SHIFT/ DELAYED OR NO ENGAGEMENT REPAIR MANUAL

download
SERVICE PROCEDURE F87Z-7A100-DB Main Control (4.0L EI Explorer) F87Z-7A100-EB Main Control (4.0L SOHC Explorer) 1. Perform normal diagnosis for this concern. XL2Z-7L491-AA Bracket XL2Z-7G383-AA Electronic Pressure Control (EPC) 2. Perform Line Pressure Tests as listed in the Solenoid 1999 Explorer/Mountaineer, Ranger Workshop Manual. OTHER APPLICABLE ARTICLES: NONE WARRANTY STATUS: Eligible Under The 3. If pressures are low, perform Pinpoint Test for Provisions Of Bumper To the EPC solenoid. Bumper Warranty Coverage And Emissions Warranty 4. Inspect the bracket that attaches the Torque Coverage Converter Clutch (TCC), Shift Solenoid B OPERATION DESCRIPTION TIME (SSB), Shift Solenoid D/Coast Clutch Solenoid 991610A Replace Electronic 1.2 Hrs. (SSD/CCS), and EPC solenoids to the main Pressure Control (EPC) control for damage. If the bracket is damaged, Solenoid And Clean Main replace both the bracket and solenoid. Control (Includes Time For 5. If the bracket is not damaged, inspect the Road Test) – 4R44E Or solenoid for the affected date code (refer to the 5R55E following Manufacturing Date Code Chart) and 991610B For Line Pressure And ID marking (Figure 1, Views 1, 2, and 3). If the Pinpoint Tests, Use “A” solenoid is one of the affected, replace it. Time As Outlined In The Warranty And Policy MANUFACTURING DATE CODE Manual Date Code Month/Year DEALER CODING 868xx August 1998 CONDITION 869xx September 1998 BASIC PART NO. CODE 870xx October 1998 7G383 01 871xx November 1998 OASIS CODES: 501000, 502000, 50300

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

1999-2004 Ford SuperDuty 4×4 Lift and Level Kit Installation Manual

download
1. With the truck on the ground, remove the track bar bolt at the differential Lift truck up, and make sure it is safe by using jack stands or a 2-post lift that locks in place. 1. Support the front axle with a support jack equipped with the proper fixture. 2. Undo the sway bar links. 3. Undo the four U-bolts on the passenger side leaf springs ONLY. Make sure the differential is supported as it may fall at this point. 4. If the truck has hydraulic shocks, just slide them up and out of the way. If the truck has gas shocks, it will be easier to remove them. Caster Left Caster Right Camber Left Camber Right Toe-in Need Camber Kit? 3 3.5 0 -1/4 -1/32 No Alignment Specifications: 1999-2004 Ford SuperDuty 4×4 Lift and Level Kit Installation 5. On the drivers side, LOOSEN but DO NOT REMOVE the U-bolts on the drivers side leaf springs. This will enable the passenger side to sag enough to get the Lift and Level kit into place. 6. Remove the center bolt on the passenger side. 7. Install the Lift and Level kit with new center bolt on the passenger side. You may wish to cut off any extra length of the center bolt once it is installed and tightened. 8. Slide the shock back on and use the pair of U-bolts to clamp the leaf springs together. DO NOT TIGHTEN the nuts on the U-bolts, just snug them enough to hold the assembly together. 9. Repeat steps from 3 to 8, using the other pair of U-bolts on the drivers side leaf spring assembly 10. Tighten all 8 U-bolts after both spring packs are installed. 11. Re-attach the sway bar links 12. Put the truck on the ground before re-attaching the trackbar. Have an assistant start the truck and turn the steering wheel until the trackbar lines up. Re-install trackbar bolt and check all the fasteners for correct torque. Test drive and align vehicle. Always check fasteners after the first test drive

2000 Ford Ranger Cooling System Draining Filling and Bleeding Repair Manual

download
NOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and support the vehicle, For additional information, refer to Section 100-02 . 3. Remove the lower radiator cover. 4. Place a suitable container below the radiator draincock. Drain the coolant. 5. Close the radiator draincock when finished. Filling and Bleeding with RADKITPLUS 1. Using the special tool, install the RADKITPLUS and follow the RADKITPLUS manufacturer’s instructions to fill and bleed the cooling system. Filling without RADKITPLUS CAUTION: Engine coolant provides freeze protection, boil protection, cooling efficiency and corrosion protection to the engine and cooling components. In order to obtain these protections, the engine coolant must be maintained at the correct concentration and fluid level. When adding engine coolant, use a 50/50 mixture of engine coolant and clean, drinkable water. To maintain the integrity of the coolant and the cooling system: * Add Motorcraft Premium Engine Coolant VC-4-A (in Oregon VC-5, in Canada CXC-10) or equivalent meeting Ford specification ESE-M97B44-A. * Do not add Motorcraft Specialty Engine Coolant such as VC-2 or an equivalent meeting Ford specification WSS-M97B44-D. Mixing coolants can degrade the coolant’s corrosion protection. * Do not add alcohol, methanol, or brine, or any engine coolants mixed with alcohol or methanol antifreeze. These can cause engine damage from overheating or freezing. * Do not mix with recycled coolants unless they meet the requirements of Ford specification ESE-M97B44-A or WSS-M97B51-A1. Not all coolant recycling processes meet these Ford specifications. Use of such coolants can harm the engine and cooling system components. All engines 1. Install the lower radiator cover.