Skip to content

chrysler sebring 2004 2 4l timing belt tensioner install

You search PDF repair manual about chrysler sebring 2004 2 4l timing belt tensioner install, if there are search results will appear below. If search results do not exist, please search by others keyword.

1997 Chrysler Sebring JXi TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
1. Disconnect negative battery cable from jumper terminal. Raise and support vehicle. Remove right front wheel. Remove accessory drive belt splash shield from right wheelwell. 2. Remove accessory drive belts. Remove right engine support assembly vertical bolts from bottom side of frame rail (timing belt end of engine). 3. Lower vehicle. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine support assembly to engine block bracket. 4. Move the A/C drier aside with hoses attached. Remove coolant reservoir tank. Remove right engine support assembly. Remove 3 bolts attaching engine support bracket to engine block, and remove bracket. 5. Remove crankshaft vibration damper. Remove power steering pump (hoses attached) and bracket from engine block. Remove timing belt covers. 6. Rotate crankshaft to align camshaft and crankshaft timing marks. 7. If reusing old timing belt, mark timing belt direction of rotation for installation reference. Loosen timing belt automatic tensioner bolts. Remove timing belt. Remove automatic tensioner. Installation 2.5L VIN H (Cirrus, Sebring Convertible & Stratus) 1. Place automatic tensioner into vise, and SLOWLY compress plunger. When plunger is compressed into tensioner body, install locking pin through body and plunger holes to retain plunger until tensioner is installed. See Fig. 13 . 2. Index tensioner in vise the same direction as installed. This will ensure proper pin orientation when tensioner is installed in engine.

2004 Kia Sorento EX TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

2003 Lexus ES 300 TIMING BELT Removal And Installation Manual

download
TIMING BELT Removal (ES 300) 1. Raise and support vehicle. Remove right side front wheel. Remove right fender apron seal. Remove accessory drive belts. Lower vehicle. Disconnect engine coolant reservoir hose from water outlet. Disconnect ground strap connectors. 2. Remove engine moving control rod and engine mounting bracket No. 2 (right side), located near timing belt cover. Remove generator-to-engine bracket for access to timing belt covers. 3. Using Pulley Holder (09213-54015) or equivalent and Handle (09330-00021) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove No. 1 and No. 2 timing belt covers and gaskets. See Fig. 1 . Remove transverse engine mounting bracket from front of engine. Note direction of timing belt guide installation for reassembly reference. Remove timing belt guide. 4. Temporarily install crankshaft pulley bolt and washer in crankshaft. Using crankshaft pulley bolt, rotate crankshaft clockwise until timing mark on crankshaft sprocket aligns with timing mark on oil pump body. See Fig. 2 . 5. Ensure timing marks on camshaft sprockets are aligned with timing mark on No. 3 timing belt cover. See Fig. 2 . If timing marks are not aligned, rotate crankshaft clockwise one full revolution (360 degrees). Remove crankshaft pulley bolt. 6. If reusing old belt, ensure there are 3 installation marks and front arrow marked on belt. See Fig. 3 . If not, place mating mark on belt where it contacts the crankshaft and camshaft sprockets. Also, mark belt with arrow showing direction of rotation. 7. Alternately loosen 2 bolts, and remove timing belt tensioner and dust boot. DO NOT hold tensioner with push rod facing downward. Remove timing belt in the following sequence: No. 1 idler pulley, right camshaft sprocket (firewall side), No. 2 idler pulley, left camshaft sprocket (front of vehicle side), left camshaft sprocket (front of vehicle side), water pump pulley, then crankshaft sprocket

1989 Nissan Pickup (200SX & 300ZX) TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal (200SX & 300ZX) 1. Disconnect negative battery cable. Release fuel pressure from system. Raise and support vehicle. Remove right wheel and engine side cover (if necessary). Drain cooling system. Remove cooling fan duct. Remove engine coolant reservoir. Remove actuator and remove radiator hoses. Do not allow coolant to contact drive belts. 2. Remove front upper and lower belt covers. See Fig. 1 . Remove drive belts and set No. 1 cylinder at TDC of compression stroke. Remove idler bracket of compressor drive belt and crankshaft pulley. Remove timing belt by removing timing belt tensioner and return spring Inspection (200SX & 300ZX) Visually inspect condition of timing belt. Inspect for cracks, wear, breaks, and oil/coolant saturation. Installation (200SX & 300ZX) 1. Ensure that piston No. 1 is at TDC of compression stroke. Remove valve covers and loosen all rocker shaft bolts. Do not bend timing belt. Install tensioner and return spring. 2. Turn tensioner clockwise and temporarily tighten lock nut. Install timing belt. Align White lines on timing belt with punch mark on camshaft pulleys and crankshaft pulley. Arrow on timing belt must be pointing toward front belt covers. 3. Using Allen wrench, slowly turn tensioner clockwise and counterclockwise 2 or 3 times. When camshafts and crankshaft marks are aligned, tighten tensioner lock nut. See Fig. 2 . Ensure that camshaft lobes are correctly positioned. Tighten rocker shaft bolts in 2 stages. 4. Refill and bleed air from cooling system. To complete installation, reverse removal procedures. Adjust drive belts to proper tension