Skip to content

civic hx drive pulley spped sensor

You search PDF repair manual about civic hx drive pulley spped sensor, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Honda Civic EX TORQUE SPECIFICATIONS

Posted by on 4 February 2012, 1:15 pm

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Filed under Honda Manuals. Tagged , , , , , , , , , , , , , , , ,
Comments Off

2001 HONDA Civic EX Replace the cylinder head assembly REPAIR PROCEDURE

Posted by on 6 June 2011, 12:28 pm

download
1. Remove the cylinder head (see page 6-30 of the 2001-02 Civic Service Manual), and discard it. 2. Inspect the TDC sensor and the timing belt covers for damage (see page 6-57 of the service manual). Replace any damaged parts. 3. Install the new cylinder head (see page 6-50 of the service manual). 4. Check the engine oil level; add oil if necessary.
2 of 2 01-083 5. Do the Idle Learn Procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine reach its normal operating temperature (the cooling fan cycle twice). Let the engine idle (throttle fully closed and with all electrical items off) for 10 minutes. 6. If you are working on a 2001 Civic 2-door EX, do the Cruise Control Learn Procedure. Drive the vehicle, and set the cruise control above 40 miles per hour. Continue driving the vehicle for 5 to 10 minutes. NOTE: You can use a smog/chassis dynamometer to do this step instead of driving the vehicle. Do not do this step with the vehicle on a lift.

Filed under Honda Manuals. Tagged , , , , , , , , , , ,
Comments Off

2001-2005 HONDA Civic Warranty Extension CVT Drive Belt Slippage

Posted by on 5 June 2011, 12:28 pm

download
DIAGNOSIS NOTE: You must complete the diagnosis before attempting any CVT repairs. 1. Civic Hybrid and Insight only: Make sure the IMA battery level gauge shows at least three quarters charged. If you need to increase the IMA charge, do this: • Insight only: Remove the EPS (electronic power steering) fuse from the under-hood fuse/relay box. •Start the engine, and run it at 3,500 rpm until the battery level gauge shows at least three quarters charged. • Insight only: Reinstall the EPS fuse. 2. Connect the HDS to the vehicle’s DLC, then turn the ignition switch to ON (II), and turn on the HDS. 3. At the HDS screen prompts, enter the VIN (if prompted) and the odometer reading. 4. At the SELECT MODE screen, select HONDA SYSTEMS . 5. At the SYSTEM SELECTION menu, select A/T . 6. From the MODE MENU, select SNAPSHOT . 7. Set these snapshot points: •Trigger type: Manual •Recording time: 2 minutes •Trigger point: -60 seconds 8. Find a flat stretch of road where you and an assistant can drive for 2 minutes at a steady vehicle speed. 9. Make sure the engine is at normal operating temperature, then using the appropriate vehicle chart below, select a vehicle speed (40, 50, 60, 70, or 75 mph) for your 2-minute snapshot. NOTE: Do not exceed the posted speed limits. Civic GX Civic HX Civic Hybrid Insight 10. Accelerate to the vehicle speed you selected, then have your assistant tap the camera icon on the HDS to trigger the snapshot. Do your best to maintain the vehicle speed and the throttle position during the snapshot. NOTE: Turn the A/C off before you capture the snapshot. 11. When the 2-minute snapshot is finished, have your assistant follow the screen prompts to save the data.

Filed under Honda Manuals. Tagged , , , , , , , , , , , , , , ,
Comments Off

2006 HONDA Civic 2/4-Door Drive Belt Auto-Tensioner Pivot Bolt Replacement

Posted by on 5 June 2011, 12:28 am

download
REPAIR PROCEDURE 1. From above the engine, set a long-handled, boxed- end wrench on the drive belt auto-tensioner. Slowly turn the wrench counterclockwise, then remove the drive belt. NOTE: On vehicles without A/C, the drive belt will be reused. 2. Insert a pulley holder (see REQUIRED SPECIAL TOOLS) into one of the holes in the water pump pulley at the 12 o’clock position. The tool holds the pulley so you can loosen or tighten the pulley bolts. 3. Remove the water pump pulley (three bolts). 4. Remove the pivot bolt from the drive belt auto- tensioner. NOTE: In rare cases, the pivot bolt may be broken. If this has happened, remove the auto-tensioner, then remove the shank of the pivot bolt with Vise Grips or by drilling it out. Do not try to repair the engine block using a TIME-SERT. If you can’t remove the shank of the pivot bolt, you would need DPSM approval to install an engine short block assembly. WITHOUT A/C WITH A/C WITHOUT A/C

Filed under Honda Manuals. Tagged , , , , , , , , , , ,
Comments Off

2003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual

Posted by on 30 June 2012, 11:43 am

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 2003 F-Super Duty 250-550/Excursion Workshop Manual 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plat 2003 F-Super Duty 250-550/Excursion Workshop Manual 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim

Filed under Ford Manuals. Tagged , , , , , , , , , , , ,
Comments Off