cost of replacing ford injector cups

You search PDF repair manual about cost of replacing ford injector cups, if there are search results will appear below. If search results do not exist, please search by others keyword.



  cost of replacing ford injector cups Direct Download speed 5432 Kb/s

  cost of replacing ford injector cups Full Version speed 8172 Kb/s



2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, ford 9 inch repair manual, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, heaf bolt torque specs 655a backhoe, windstar dtc u1131

Ford 455C 555C 655C Tractor Loader Backhoe Service Manual

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Engine Systems Chapter 1 3-Cylinder Diesel Engine 3-Cylinder Diesel Engine – Description and Operation 3-Cylinder Diesel Engine – Overhaul Chapter 2 4-Cylinder Diesel Engine 4-Cylinder Diesel Engine – Description and Operation 4-Cylinder Diesel Engine – Overhaul Chapter 3 Cooling System Cooling System – 3-Cylinder Engine Description and Operation Cooling System – 4-Cylinder Engine Description and Operation Cooling System – Overhaul Chapter 4 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 2 Fuel Systems Chapter 1 Fuel System – General Fuel System – Description and Operation Fuel System – Adjustments DPA Distributor Type Fuel Injection Pump Fuel System – Adjustments DPS Distributor Type Fuel Injection Pump Fuel System – Fuel Tanks, Filters and Fuel Lines Overhaul Chapter 2 Fuel Injection Pump – DPA Distributor Type Fuel Injection Pomp – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedures Chapter 3 Fuel Injection Pump – DPS Distributor Type Fuel Injection Pump – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedure Chapter 4 Injectors Ford 455C Injectors – Description and Operation Injectors – Overhaul Chapter 5 Injectors Ford 555C and 655C Injectors – Description and Operation Injectors – Overhaul Chapter 6 Air Cleaners Dry Type Air Cleaner – Description and Operation Dry Type Air Cleaner – Overhaul Chapter 7 Turbocharger Turbocharger – Description and Operation Turbocharger – Overhaul Chapter 8 Troubleshooting, Specifications, Test Plans and Special Tools Troubleshooting – Diesel Engines Troubleshooting – Turbocharger Specifications Special Tools Test Plans Part 3 Electrical System Chapter 1 Wiring, Lights and Controls Wiring, Lights and Controls – Description and Operation Wiring, Lights and Controls – Fault Finding and Repair Circuit Diagrams and Wiring Harness Chapter 2 Battery
Battery – Description and Operation Battery – Maintenance and Tests Chapter 3 Starting System Starting System – Description and Operation Starting Motor – Overhaul Chapter 4 Charging System – A127 55 Amp Alternator with Integral Regulator Charging System – A127 55 Amp Alternator with Integral Regulator – Description and Operation Charging System – A127 55 Amp Alternator with Integral Regulator – Service Precautions, Preliminary Checks, Initial Tests and Alternator Component Tests Charging System – A127 55 Amp Alternator with Integral Regulator – Overhaul Chapter 5 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 4 Power Reversing Transmission Chapter 1 4×4 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul Chapter 2 8X8 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit, Lockup Valves and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul

Related Content:

MERCEDES BENZ KE JETRONIC FUEL SYSTEM TROUBLE TRACER, ford 550 backhoe operator manual, how to repair fuel injectors on 2003 GMC Envoy, procedure for overhauling a gear pump, dpa injector pump govenor spring settings, Lucas feul injector pump type 908 for tractor, ford 555c alternator wiring diagram, n14 cummins troubleshooting, injection pump timing on a db4429 pump, j-38791 moore

Toyota LandCruiser 4.2TD Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 02-03-2012

download
Timing belt replacement intervals The information relating to timing belt replacement intervals is additional to the main purpose of this CD, but is included to provide guidance to garages and for customer advice. Where possible the recommended intervals have been compiled from vehicle manufacturers’ information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully later in this section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. 6. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. 7. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. 8. If in doubt about the condition of the belt – RENEW it. 9. Removal Removal Remove timing belt cover [1]. 1. Turn crankshaft clockwise until timing marks aligned [2]. 2. Ensure timing marks aligned: 1KZ-T/TE: [3]. 3. 4. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. 5. Installation Installation Check tensioner pulley for smooth operation [8]. Replace if necessary. 1. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. 2. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. 3. Slowly compress pushrod into tensioner body until holes aligned. Use press. 4. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. 5. Ensure timing marks aligned [2]. 6. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 7. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. 8. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. 9. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. 10. Remove Allen key from tensioner body to release pushrod. 11. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. 12. If not: Repeat installation and tensioning procedures. 13. Install components in reverse order of removal. 14. Reset timing belt replacement warning lamp as follows: 15. -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 16. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 17. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

Related Content:

mazda bt50 timing belt replacement, 4 7L Toyota Timing Belt Replacement, Kia 3 5 Timing Belt Replacement, honda odyssey timing belt replacement mileage, 2004 subaru forester XT timing you tube instalation, Timing Belt Replacement Intervals Pontiac, how often change timing belt 2011 chevy malibu, how to change a timing belt on a 2011 kia soul, how to install varable timing solenoid on gmc envoy xuv 4 2l, how to remove a three bolt crankshaft pulley mazda bt 50

HONDA Front Seat Belt Replacement Warranty Policy

0

Filed Under (Honda Manuals) by admin on 24-11-2011

download
CUSTOMER INFORMATION : The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your car. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your car, or that your car has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. ? 1996 American Honda Motor Co., Inc. – All Rights Reserved . ATB 14788-17665 (9601) 1 of 2 JAN 22, 1996 92-012 BODY ALL 1986 and later Applicable To Model File U nder Issu e D ate Bulletin N o. Service Bulletin Front Seat Belt Replacement Warranty Policy (Supersedes 92-012, dated March 13, 1992) Warranty policy for front seat belt replacement is to replace either the belt/retractor mechanism or the buckle when either does not work properly. Warranty covers the replacement of the failed half of a belt, not the entire assembly (see PARTS INFORMATION ). NOTE: For 1970 through 1985 models, seat belts are replaced as a complete assembly under a separate warranty policy. COMPONENT REPLACEMENT Front seat belts are made by several suppliers, and some are sold as individual components (two separate halves); they are not stocked as a complete set. Therefore, whenever you replace a belt, make sure the new belt half is the same type and from the same manufacturer as the original – otherwise, the belt may not buckle properly. To determine the manufacturer and type (or “model”) of the belt, look for the white tag on the original belt in the car. The tag is on the retractor side of the belt (visible at the lower attachment point), or on the belt if you pull the belt all the way out. From the tag, mark down the manufacturer’s name (either Nippon Seiko K.K. or Takata), the belt “model” number and the date of manufacture. If the tag is missing or illegible, look on the buckle component for the name Nippon Seiko K.K. or the stylized “T” mark () for Takata. NOTE: Some belts may have NSK Warner K.K. as the manufacturer’s name. Use Nippon Seiko K.K. belts as the replacement. Take the information to your Parts Department to order the proper replacement belt. NOTE: For more information on seat belts and seat belt related items read: -Twisted Seat Belt (ServiceNews, July ’85) -Seat Belt Testing and Repair (Service Bulletin 86-014, August ’86) -Automatic Seat Belt Troubleshooting (ServiceNews, May ’89) -Lap Belt Retracts Slowly (Service Bulletins 90-003, January ’90 and 90-012, April ’90) -Torn Seal on Seat Belt Track (Service Bulletin 91-004, March ’91) -Slow to Retract Seat Belt, Cleaning the Guide Ring (ServiceNews, April ’91) -Accord Shoulder Belt System Wire Colors (ServiceNews, May ’91) -Seat Belt Slow to Retract (Service Bulletin 91-030, December ’91) Refer to your Service Bulletin Index and the ServiceNews Index for model specific information. Most repairs do not require seat belt component replacement. PARTS INFORMATION For front seat belt replacement ordering information and availability, contact your parts center.

Related Content:

1986 chevy c10 new belt, installing new rotors on a 1992 ford f250 4wheel drive, volvo 850 repair seat belt tensioner manual download, 2004 chevy malubu surpupten belt replacement on a 2 2 liter on you tube, 2002 chevy malibu passlock gm bulletin, sun visor repairs 2013 honda accord, snugtop glass button bolt, replace sun visor 09 honda accors, repairing seat belt in dodge dakota, 1990 HONDA CIVIC SEATBELT FUSE BLOCK

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-07-2012

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

Related Content:

Sienna Sliding Door Cable Replacement, 1998 sienna repair manual, how to fix g-6 door latch, how to remove a chevy tahoe bump stop, lexus door adjustment wind, tool for removeing the rear brake shoe retainer spring clip on 2013 isuzu nrr series, toyota sienna sliding door repair manual

1997 Ford F-250/ 350/ Super Duty Steering Knuckle REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 13-06-2012

download
Steering Knuckle Removal 1. Remove the front wheel spindle (3105) and the right and left shaft and joint assembly. Refer to Spindle, RH and LH Shaft and Joint Assembly in the Removal and Installation portion of this section. 2. Disconnect the steering linkage, if necessary, from the knuckle. Refer to Section 11-03 in the Body, Chassis Manual. Steering Knuckle Installation 3. Remove the cotter pin from the stud of the front suspension upper ball joint (3049). Loosen the nut on the top stud and the bottom nut inside the steering knuckle. Remove the top nut. 4. Sharply hit the top stud with a plastic or rawhide hammer to free the knuckle from the axle arm. Remove and discard bottom nut. 5. NOTE: Note the orientation of the camber adjuster to make sure of the same camber setting. Remove camber adjuster by hand or, if difficulty is encountered, use Pitman Arm Puller T64P-3590-F. 6. Place steering knuckle in vise and remove snap ring from bottom ball joint socket if so equipped. 7. Remove plug from U-Joint Tool T74P-4635-C and replace with Plug T80T-3010-A4 (part of 4WD Ball Joint Tool Set T80T-3010-A). 8. Assemble U-Joint Tool T74P-4635-C and Receiving Cup T80T-3010-A2 (part of 4WD Ball Joint Tool Set T80T-3010-A). 9. NOTE: Always remove front suspension lower ball joint first. Turn forcing screw clockwise until front suspension lower ball joint is removed from steering knuckle. 10. Repeat procedure and remove front suspension upper ball joint. Installation 1. Clean steering knuckle bore and insert front suspension lower ball joint as straight as possible. 2. NOTE: If ball joint cannot be installed to the proper depth, realign Receiving Cup T80T-3010-A3. To replace the front suspension lower ball joint, assemble U-Joint Tool, Receiving Cup T80T-3010-A3 (part of 4WD Ball Joint Tool Set T80T-3010-A) and Installing Cup from Ball Joint Adapter Set D81T-3010-A or equivalent. 3. Turn forcing screw clockwise until front suspension lower ball joint is firmly seated. 4. Install the snap ring on the front suspension lower ball joint. 5. To install front suspension upper ball joint, assemble the C-Frame, Receiving Cup T80T-3010-A3 and Replacer T80T-3010-A1 (both part of 4WD Ball Joint Tool Set T80T-3010-A). 6. Turn forcing screw clockwise until front suspension upper ball joint is firmly seated. 7. Assemble knuckle to axle arm assembly. Install camber adjuster on the stud of the front suspension upper ball joint with the arrow pointing outboard for positive camber, pointed inboard for negative camber. 8. Install new nut on bottom socket finger-tight. Install and tighten nut on top socket finger-tight. Tighten bottom nut to 47 Nm (35 lb-ft). 9. CAUTION: If the tightening sequence is not followed in this step and Step 10, ball joint life will be reduced. NOTE: Do not loosen top nut to install cotter pin. Tighten top nut to 136 Nm (100 lb-ft), then advance nut until castellation aligns with cotter pin hole. Install cotter pin. 10. Retighten bottom nut to 123-149 Nm (91-110 lb-ft). 11. Install the front wheel spindle and the right and left shaft and joint assembly as described in this section. 12. Connect steering linkage, if necessary, to the knuckle. Refer to Section 11-03 in the Body, Chassis Manual.

Related Content:

removing trailblazer ball joints, 2004 dodge ram 1500 torque values front end ball joints swaybar links whjeels, how to replace rear upper arm kia sedona, torqe for ball joint 2001 prizm, oem ball joint press, peugeot 306 front lower arm removal, lower ball joint press sedona kia, Is an alignment required after replacing lower ball joints on a 2008 chevrolet silverado?, how to replace the lower and upper ball joints ona 1995 dodge 1500 2 wheel dr at home with no lift, how to replace bal joint hyundat accent 2000

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010