cost to replace rear end on 2004 f150

You search PDF repair manual about cost to replace rear end on 2004 f150, if there are search results will appear below. If search results do not exist, please search by others keyword.



  cost to replace rear end on 2004 f150 Direct Download speed 5432 Kb/s

  cost to replace rear end on 2004 f150 Full Version speed 8172 Kb/s



2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 27-06-2012

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.

Related Content:

rockauto com 1999 ford winstar vent window bolt, ford 2001 f150 window removal, how to remove a rear hatch door on a Chev Trailblazer, F250 Rear Glass replace, 2011 ford F150 clunking rear end sound, 2010 Ford F150 rear window defroster harness, 2008 tahoe rear window button broken, how to install manual window door 04 f150, 2001fordf150rearwindowremoveal, 2004 f150 back window assembly

TOYOTA LANDCRUISER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 10-11-2011

download
INSTALLATION INSTRUCTIONS 1. Park the vehicle on a level surface. Check the vehicle height from side to side and front to back. This is done by measuring from the ground up to the fender using the hub as a centering point. 2. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of the new front springs. Now apply a thin coat of grease on outside of bushings. This will help you to insert the bushing into the spring mount. 3. Raise the front of the vehicle and support securely with jack stands under the frame behind the front springs, and block the rear wheels. Remove the tires, shocks, u-bolts, and loosen the sway bar bolts. (Caution: the front axle will now be free to move, so support securely on floor jack.) 4. With a floor jack supporting the axle, unbolt each end of leaf springs and remove from both sides. (If new shackle bushings were purchased, grease and install them in the frame at this time.) Install new front springs, part # 8041. When installing the front springs that the fat part of the shim on the bottom of the spring pack should be pointing toward the rear of the vehicle. Notice the tie bolt in the front leaf springs is not in the center of the leaf spring, but there is a long end and short end. Install the springs with the short end towards the rear, and long end towards the front bumper. Do not tighten spring eyebolts at this time. 92756702 64-80 TOYOTA LANDCRUISER INSTALLATION
INSTRUCTION SHEET Technical Assistance – (731) 285-9000 Page 2 5. Using the floor jack, lower the front axle down to the leaf springs. Be sure the tie bolts align and fit into the tie bolt holes in the front axle housing. Install and tighten new u-bolts. Torque u-bolts to 75-90 ft.lbs. 6. Install new shocks and tires then lower the vehicle to the ground. Tighten spring eyebolts at this time. NOTE: The drag link that goes along side of the frame from the gear box to the bell crank may require slight bending for clearance of the new shock. Bending this drag link will not affect it, but do not kink the bar. 7. Raise the rear of the vehicle. Support securely with jack stands and block the front wheels. Remove the tires, shocks, and u-bolts. (CAUTION: the rear axle will be free to move, so support securely on a floor jack. 8. Apply a thin coat of grease to the polyurethane bushings and insert into each eye of the new rear springs. Now apply a thin coat of grease on outside of bushings. This will help you to insert the bushing into the spring mount. 9. With a floor jack supporting the rear axle, unbolt each end of the rear leaf spring and remove from both sides. (If new shackle bushings were purchased, grease and install them in the frame at this time.) Install new springs, part # 8042. When installing the rear springs the fat part of the shim on the bottom of the spring pack should be pointing toward the front of the vehicle. Notice the tie bolt in the rear leaf springs is not in the center of the leaf springs, but there is a long end and a short end. Install the springs with the short end towards the front and longer end towards the rear bumper. Do not tighten spring eyebolts at this time. 10. Using a floor jack, lower the rear axle down to the leaf springs. Be sure tie bolts align and fit into the tie bolt holes in the axle housing. Install and tighten new u-bolts, shocks and tires then lower vehicle to the ground. Torque u-bolts to 75-90 ft.lbs. Tighten spring eyebolts at this time.

Related Content:

ford 8 8 rear end rebuild, tahoe balance bar repair, 04 ford f150 8 8 rear end rebulid, replacing a 1997 ford thunderbird rear end, rear for equinox 2005 bolt kit, Meritor Rear Axle Parts Breakdown, how to disassemble 8 inch ford rear axles, grease maintenance for 1997 ford f350, GM 14 BOLT REAREND MANUAL, ford 9 75 rear end specs

2007 HONDA ODYSSEY SPLASH GUARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 14-10-2011

download
INSTALLATION NOTE: •These instructions show the left splash guards being installed. The same procedure applies to installing the right splash guards. •Clean and wax the areas to be covered with a high-quality paste wax. Installing the Front Splash Guards 1. Turn the steering wheel all the way counter clockwise to provide access to the left front fenderwell. 2. Remove the two self-tapping screws from the left front inner fender. PARTS LIST Right front splash guard Left front splash guard Right rear splash guard Left rear splash guard 6 Self-tapping screws 2 Spring nuts 2 Square head grommets 3. Using a pushpin, make a small hole through the center of the upper clip. UPPER CLIP PUSHPIN SELF-TAPPING SCREW LEFT FRONT INNER FENDER SPLASH GUARDS P/N 08P00-SHJ-101 2 of 2 All 33039-33598 (0608) LEFT REAR SPLASH GUARD SELF-TAPPING SCREW LEFT REAR FENDERWALL SELF- TAPPING SCREW (reused) REAR BUMPER LEFT REAR SPLASH GUARD There must be no clearance. REAR BUMPER LEFT FRONT INNER FENDER LEFT FRONT SPLASH GUARD LEFT FRONT INNER FENDER SELF- TAPPING SCREW LEFT FRONT SPLASH GUARD CLIP CLIP SELF- TAPPING SCREW SELF-TAPPING SCREW (reused) LOWER HOLE 5. While holding the left splash guard against the fender, tighten the self-tapping screws in the order shown. 6. Turn the steering wheel all the way clock wise and repeat steps 2 through 4 to install the right front splash guard. Installing the Rear Splash Guard 7. Using a floor jack, lift up the left rear side of the vehicle according to the service manual. 8. Remove the self-tapping screw from the rear bumper. Using a pushpin, make a hole through the center of the recess. 9. Install one square head grommet into the hole in the left rear fenderwall. Slide one spring nut over the hole you made in step 8 in the rear bumper. 10. Position the left rear splash guard on the left rear fenderwall and rear bumper, and loosely install one self-tapping screw you removed, and the two self-tapping screws supplied with the kit. LEFT REAR FENDERWALL REAR BUMPER SELF-TAPPING SCREW (Reuse.) SQUARE HEAD GROMMET SPRING NUT RECESS PUSHPIN REAR BUMPER With RECESS SELF- TAPPING SCREW 4. Install the left front splash guard using the two self-tapping screws removed in step 2, and one self-tapping screw supplied with the kit. Do not tighten the self-tapping screws yet. 11. Hold the left rear splash guard against the fenderwall and check that there is no clearance between the splash guard and rear bumper. Tighten the three self-tapping screws in the sequence shown. 12. Repeat steps 7 thru 11 to install the right rear splash guard

Related Content:

yhs-fullyhosted_003, how do you replace liftgate relay for 2005 escalade, rear hub assembly removal for 2008 toyota tundra, installation instructions for a 2007 honda accord front bumper, ruff and tuff golf cart parts rear axle bearing, rear cam seal 2000 monterro, Rear brakes 2000 Jag xj8 procedure, rear ac lines on 05 chevy trailblazer, lincoln ls rear suspension squeak, liftgate actuator replacement tahoe

2007 Toyota Camry Rear Bumper Removal and Replacement Manual

0

Filed Under (Toyota Manuals) by admin on 26-01-2012

download
REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. INSTALLATION 1. INSTALL REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Engage each claw.

Related Content:

2005 F250 Ford Truck rear brake backing plate, how to remove rear bumper 2008 camry, time it takes to repair front bumper for 2007 toyota camry

2006 HONDA CR-V CARGO COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 12-10-2011

download
INSTALLATION Installing the Cargo Cover 1. Open the tailgate. Using a flat-tip screwdriver, remove the panel covers from the right and left rear side trim panels. SUPPLIES REQUIRED Flat-tip screwdriver Clean soft cloth Cargo cover 2 Adhesive tapes 2. Using a clean soft cloth, clean the areas where the panel covers were removed. Remove the adhesive backings from the adhesive tapes, and attach the tapes to the right and left, rear side trim panels where the panel covers were removed. 3. Insert the left end of the cargo cover into the recess in the left rear side trim panel; compress the cargo cover, and insert the right end into the recess in the right rear side trim panel as you release the cover 4. Attach the four front roll cover hooks to the rear seat headrest posts as shown. 5. Slide both ends of the rear roll cover rod into the recesses in the rear side trim panel. Storing the Cargo Cover 6. Insert the right end of the cargo cover into the recess in the right rear side trim panel; compress the cargo cover, and insert the left end into the recess in the left rear side trim panel by compressing the cargo cover, and aligning the end with the recess in the left rear side panel. USE AND CARE •The front roll cover cannot be used when the rear seat is stored. •Do place cargo on the front and rear roll covers. •Do not hang anything from the roll cover hooks. REAR SEAT HEADREST ROLL COVER HOOKS (4) HEADREST STAY CARGO COVER CARGO COVER ROLL COVER ROD

Related Content:

2011 gmc terrain headrest dvds, 2012 honda civic coupe undercarriage cover, 5r55e transmission servo cover blew out AND DAMAGED CASE case, ford 6 0 hpop valve cover torque specifications, install fj cruiser cargo cover

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

0

Filed Under (Toyota Manuals) by admin on 22-06-2012

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

Related Content:

2006 pontiac torrent liftgate release switch, 2004 Toyota Sienna Manual PDF, 2006 cadillac escalade liftgate problem blows fuses, free repair manual for a 2004 toyota sienna, owners manual for a 2006 scion xb, pt cruiser owners manual 2006, replace 2007 pacifica liftgate assists

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, 2005 explorer transmission exploded view, how to check tranmission fluid on 2012 kia sedona, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 2011 crv engine whine, gm4160e band adjustment screws, 1997 e450 power stroke trans mount parking brake, transmission module for 1999 ford ranger xlt

2003-2007 Dodge (DR/DH/D1/DC) Ram Truck Front EndShimmy On 4×4 Vehicles When Traveling Over Rough Surfaces In The Road

0

Filed Under (Dodge Manuals) by admin on 17-04-2014

download
REPAIR PROCEDURE: 1. Raise the vehicle on an alignment rack (drive-on lift). 2. Verify the road tires are correctly sized and the tire tread is not excessively worn. Replace any worn tire before proceeding. Any new or old replacement tire should be equal to the original tires that came with the vehicle when it was new. Tire wear is not covered by the vehicle warranty. 3. Set the tire pressure for the FRONT TIRES to the following specification, regardless of the load being carried by the vehicle . Tire Size FRONT Tire Pressure LT235/80R17EorLT245/70R17E 448 Kpa (65 psi) LT265/70R17EorLT285/70R17E 414 Kpa (60 psi) 4. Set the tire pressure for the REAR TIRES as recommended for the vehicle configuration and load that is being carried at the time. Tire Size REAR Tire Pressure LT235/80R17EorLT245/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. LT265/70R17EorLT285/70R17E Refer to the Tire Inflation Chart brochure in the Owners Manual or to the placards located either on the face of the driver’sdoor or on the driver’sside”B”pillar. 5. Verify that the steering damper is operating correctly. a. Unbolt the end of the damper at the axle end. b. Cycle the damper rod by hand. c. There should be resistance to motion in both directions of the damper rod. d. Replace the damper if no resistance is present. 6. Verify both outer tie rod ends dustcovers are not worn. a. Attempt to rotate the dustcover by hand. b. If the dustcover on an outer tie rod end can be rotated, or is free and loose, then replace the tie rod (regardless of joint wear). 7. Inspect each outer tie rod end for internal wear. a. Maximum allowed wear (joint travel) fora tie rod end is 1.15 mm (0.045 in.). b. Install a dial indicator to the tie rod end (in-line with the vertical stud of the tie rod end). c. With a pry bar placed between the steering linkage and the axle tube, pry upwards while measuring the amount of joint travel (wear). d. Measure the amount of wear in the other outer tie rod end joint. e. If wear (joint travel) in either outer tie rod end is greater than 1.15 mm (0.045 in.), then replace the worn tie rod end. 8. Verify the torque on each outer tie rod end stud nut. The nut should be tightened to 122 Nm (90 ft. lbs.). 9. Make sure any worn outer tie rod ends have been replaced before proceeding further. 10. Verify all other steering linkage connections are tightened to their torque specifications.

Related Content:

2001 doge neon how do you line the front tires, adjust wheel bearing on a 1999 gmc 6500, 302 roller cam eccentric, how much should it cost in the state of florida to repair the carbon canister on a 2003 kia optima, how to set the tie rod on a 2005 malibu, how to get axle out 1997 ford f150, repair àxle seal 2007 toyotayaris, replace antenna 2001 tacoma, 2000 gmc purge valve repair, 1998 dodge ram van repair manual free download

2009 HONDA ODYSSEY THIRD ROW SEAT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 25-10-2011

download
INSTALLATION NOTE: Do not install seat cover to the front seats. 1. Push the knob to release the rear seat head rests shown. KNOB Push. REAR SEAT HEAD REST COVER REAR SEAT HEAD REST REAR SEAT HEAD REST BOTTOM SIDE 2009 ODYSSEY AUG 2008 AII 4023 cover onto the head rest from the bottom side as Improperly covering the front seat back can prevent from the rear seat. Install the rear seat head res 2. Install the rear left seat cover to the rear left seat in the following order ( ) . Push in. REAR LEFT SEAT REAR LEFT SEAT COVER REAR LEFT SEAT VELCRO FASTENER VELCRO FASTENER Push in. REAR RIGHT SEAT COVER REAR RIGHT SEAT VELCRO FASTENER VELCRO FASTENER REAR RIGHT SEAT Push in. 3. Install the rear right seat cover to the rear right seat in the following order ( ) . Install the headrests back onto the rear seats. Make sure the head rest button is not covered.

2004 Toyota Prius EV (Electric Vehicle) Button Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Time and Difficulty: I found the install to be moderately difficult and pretty time-consuming (about 3 hours) ; others have found it simple and report they have done it in as little as 30 minutes. Your experience will depend on your familiarity with the tools and electronics. I, personally, found insertion of the connection pin into the HV ECU plug to be difficult and almost got the first pin irrevocably stuck in the slot. I spent quite a bit of time with that part alone. I also found threading the wire behind the dash to be fairly tricky. I think the average person, not encountering any problems, could do this job in about 1-1½ hours. Procedure in Brief: 1) Remove bottom cover of steering wheel 2) Locate and unplug flasher plug 3) Open plug and remove 1-3 unused connector pins 4) Reattach steering wheel cover 5) Dismantle part of dash (vents) and remove lower glove box 6) Locate HV ECU (gray plugs) and remove lower plug 7) Solder wire to connector pin and insert into ECU plug (#27) 8) Splice EV button ground wire into ECU plug ground wire (#1) 9) Plug ECU plug back into the ECU 10) Thread wire behind dash to opening near dimmer switch 11) Attach switch to cover and solder wires in place 12) Reassemble the dash 13) Test Procedure in Detail: *Review ALL steps before proceeding and be sure you understand all terms used and you’ve looked at all diagrams and pictures. 1) Remove the bottom cover of the steering wheel by releasing the steering wheel adjustment handle and unscrewing the silver screw in that recess. 2004_prius_evv2.doc Page 4 of 20 Last updated March 13th, 2004 Then, turn the steering wheel 90 degrees right and remove the black screw that becomes visible on the right side of the steering column. Then turn the wheel 180 degrees left (90 degrees from normal position) and remove the black screw on the left side of the steering column. Carefully pull down on the lower portion of the steering column cover until it releases. Mine was a bit stiff/stuck to the upper part and you may need to carefully use a butter knife or screwdriver to start prying them apart. 2004_prius_evv2.doc Page 5 of 20 Last updated March 13th, 2004 2) Locate and unplug the white flasher plug visible just on the left side of the bottom of the steering column. 3) 2 little clips keep a cover locked in place. Pull those apart and remove the cover. Inside you’ll see lines of silver connector pins–some with wires attached, some without. You should remove between 1 and 3 of those pins–2 is probably safe, 3 might be better, since if you plan to install an OEM button at some point, you’ll probably need more pins for that. (You need one pin for the procedure, but it’s handy to have a back-up.) To remove the pins, you can use your paper clip to start the process of sliding them out, and then they just pull right out. 2004_prius_evv2.doc Page 6 of 20 Last updated March 13th, 2004 Stick them to a piece of tape or put them somewhere secure so you can find them later. Snap the cover back into place, and plug the flasher plug back in. 4) Replace the steering wheel cover by reversing the process. Be sure everything’s aligned properly and that there are no gaps. 5) Now you’ll need to dismantle part of the dash to get access to the ECU and other areas. First, open the top and bottom glove box doors. Squeeze the inside sides of the lower glove box together to get the catches past the portion of the dash frame that keeps the door from falling all the way open. Then pull the entire door straight toward you – it will unclip from the hinges at the bottom of the glove box. 2004_prius_evv2.doc Page 7 of 20 Last updated March 13th, 2004 You may also need to unclip the little hydraulic piston that keeps the door from falling open too quickly. Next, grasp the bottom of the silver vent piece next to the glove box. Pull it toward you firmly. It should unclip at the bottom first. Then pull the whole unit straight out

Related Content:

2004 Sienna Fuse Box Diagram, 2004 Chevrolet Malibu Classic Manual Free, 02 ford xlt fx4 air breather diagram, 2004 mazda 3 headlight adjustment, all air vents open on 2004 ford explorer, how to reset computer on 2004 chevy impala, 2004 gto repair manual, reset security on 2004 maxima, exhaust system for 2004 malibu maxx lt, service manual 2004 chevrolet monte carlo pdf

Related Content:

rockauto com 1999 ford winstar vent window bolt, ford 2001 f150 window removal, how to remove a rear hatch door on a Chev Trailblazer, F250 Rear Glass replace, 2011 ford F150 clunking rear end sound, 2010 Ford F150 rear window defroster harness, 2008 tahoe rear window button broken, how to install manual window door 04 f150, 2001fordf150rearwindowremoveal, 2004 f150 back window assembly