Skip to content

d16y8 intake torque sequence

You search PDF repair manual about d16y8 intake torque sequence, if there are search results will appear below. If search results do not exist, please search by others keyword.

Chrysler V8 DUAL QUAD INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
PREP AND TUNING FOR POWER: NOTE: This manifold will produce optimum power and drivability when used with #1405 carburetors. Please refer to Edelbrock Performer Series Carburetor Owner’s Manual for tuning procedures. 1. Edelbrock has found, while dyno testing on a Performer level engine at our location, the best calibration to be: Metering Rods – .070″ x .047″ (stock 1405), Primary Jets – .098″ (provided with intake manifold), and Secondary Jets – .086″ (provided with intake manifold). This will vary according to engine build and atmospheric conditions. Use it as a starting point. However, if used for racing or marine installation, further tuning may be necessary. 2. Aftermarket distributor curve kits may be used with this intake manifold. A basic ignition curve of 12° to 14° initial and a total of 36° to 38° advance is a good starting point. 3. Use modified or high performance cylinder heads such as our Performer RPM. 4. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this condition occur, recalibrate with a richer jet. • CAMSHAFT AND HEADERS: Dual Quad manifolds are compatible with aftermarket camshafts and headers. Header primary tube diameter should be 1-7/8″, depending on the specific engine combination. Edelbrock has developed two camshafts for use with this intake manifold – Performer-Plus #2192 or Performer RPM #7194. Please check the catalog or website for rpm and application guidelines. INSTALLATION 1. Use only recommended intake gaskets set when installing this intake manifold. For ease of installation, we recommend Edelbrock Manifold Bolt and Washer Kit, #8594. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Use a factory style valley pan along with the recommended gaskets. 4. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 5. Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs

Chrysler 413-426 CH- 6 B CHRYSLER 6 -PACK INTAKE MANIFOLD INSTALLATION MANUAL

download
NOTE: Please refer to Edelbrock Performer Series Carburetor Owner’s Manual for detailed tuning procedures. 1. Due to design, the fuel/air mixture and cylinder charging are very efficient with the CH-6B intake manifold. Generally speaking, the stock jetting for the recommended aftermarket carburetors will not need changing. Specific applications may show an increase in performance through further tuning. 2. Aftermarket distributor curve kits may be used with this intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM. 4. The compression ratio should be at least 9.5 to 1 to work properly with Performer RPM camshafts. 5. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this occur, recalibrate with a richer jet INSTALLATION: 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Use a factory style valley pan along with the recommended gaskets. 4. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 5. Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs.

1999 Honda Civic EX TORQUE SPECIFICATIONS

download
TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket-To-Engine Bolts 33 (45) A/C Compressor-To-Bracket Bolts 18 (24) A/C Idler Pulley Bracket Bolts 8-mm 18 (24) A/C Idler Pulley Center Nut 33 (45) Battery Tray 18 (24) Camshaft Holder Bolts DOHC 8-mm Bolts 20 (27) SOHC 8-mm Bolts 15 (20) Camshaft Pulley Bolt DOHC 41 (56) SOHC 27 (37) Catalytic Converter Flange Nuts 25 (34) Clutch Slave Cylinder Line/Hose Bracket 8-mm Bolts 18 (24) Clutch Slave Cylinder Mounting 8-mm Bolts 18 (24) Connecting Rod Bearing Cap Nuts DOHC 30 (40) SOHC 23 (31) Crankshaft Pulley Bolt DOHC 130 (177) SOHC (1) Cylinder Head Bolts DOHC First Step (Bolts 1-10) 22 (29) Second Step 61 (83) SOHC First Step (Bolts 1-10) 15 (20) Second Step (Bolts 1-10) 36 (49) Thrid Step (Bolts 1-10) 49 (67) Forth Step (Bolts 1 & 2) 49 (67) Distributor Mount Bolt 18 (24) Drive Plate Bolts (A/T Or CVT) 54 (74) EGR Valve Nuts 15 (20) Engine Coolant Drain Plug 58 (79) Engine Mounts (2) Transaxle Mount 10-mm Bolts 12-mm Bolts/Nuts 47 (64) 12-mm Through-Bolt 54 (74) Side Engine Mount 10-mm Nuts/Bolts 40 (54) Engine Upper Mount Bracket 74 (54) Rear Mount Bracket 12-mm Bolts 43 (59) 14-mm Bolts 61 (83) Left Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 43 (59) Right Front Mount 10-mm Bolts 33 (44) 12-mm Bolts 47 (64) Engine Oil Drain Plug 33 (45) Engine Front & Rear Stiffeners 8-mm Bolts 18 (24) 10-mm Bolts 33 (44) 12-mm Bolts 42 (57) Exhaust Manifold Bracket Bolt 8-mm 18 (24) 10-mm 33 (45) Exhaust Manifold Cover 8-mm Bolts 18 (24) Exhaust Manifold-To-Cylinder Head Nuts (3) 23 (31) Exhaust Pipe Bracket 8-mm Nuts (3) 12 (16) Exhaust Pipe Flange 8-mm Bolts (3) 16 (22) Exhaust Pipe-To-Manifold/TWC (3) D16Y5 & D16Y7 Engines 25 (33) D16Y8 & B16A2 Engines 40 (54) Flywheel Bolts (M/T) 87 (118) Fuel Filter Banjo Bolt 25 (34) Generator Adjustment Lock Bolt 18 (24) Generator Bracket-To-Engine Bolts 33 (45) Heated Oxygen Sensor (HO2S) 33 (45) Inspection Hole Sealing Bolt (VTEC) 15 (20) Intake Air Control (IAC) Valve Bolts D16Y5 Engine 16 (22) D16Y8 Engine 18 (24) Idler Pulley Bracket Bolt DOHC

Chevrolet V8 With General Duty Oval Port Cylinder Heads STREET TUNNEL RAM INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
CAMSHAFT AND HEADERS: The Street Tunnel Ram manifold is compatible with aftermarket camshafts and headers. Use Edelbrock Torker-Plus camshaft #5062 for more low RPM torque, or the Edelbrock Performer RPM camshaft #7162 for more high RPM power. Header primary tube diameter should be 1-7/8″. This may vary depending upon your particular engine specifications. PREP AND TUNING FOR POWER: 1. Specific applications may show an increase in performance through additional carburetor tuning. 2. Aftermarket distributor curve kits and aftermarket ignitions may be used with the Street Tunnel Ram intake manifold. 3. Use modified or high performance cylinder heads such as our Performer RPM, and port match the intake manifold to the heads. 3. The engine’s compression ratio should be at least 9.5:1 to work properly with Torker-Plus or Performer RPM camshafts. INSTALLATION PROCEDURE INTAKE MANIFOLD BASE 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 4. Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼” high bead across each block end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal slippage. 5. Install the intake manifold hold-down bolts. Hand tighten all bolts to approximately 5 ft./lbs. to center the manifold on the engine. WARNING: There is no gasket support for the manifold under the four bolt holes which are numbered 13,14,15, and 16 in Figure 1 below. Damage to the manifold will occur if these four bolts are over tightened. Hand tighten these bolts with a 6″ box-end wrench. DONOT use a torque wrench. 6. Torque all of the remaining manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs. INTAKE MANIFOLD TOP 1. Apply Edelbrock Gasgacinch sealant P/N 9300 to the gasket mating surface and install the gasket and manifold top. 2. Install and tighten the supplied hold down bolts to 15-18 ft./lbs.

305-400 C.I.D. Chevrolet V8 STREET TUNNEL RAM INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

download
INSTALLATION PROCEDURE INTAKE MANIFOLD BASE 1. Use only recommended intake gaskets set when installing this intake manifold. 2. Fully clean the cylinder head intake flanges and the engine block end seal surfaces. 3. Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to air dry, and attach the intake gaskets. 4. Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼” high bead across each block end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal slippage. 5. Install the intake manifold hold-down bolts (We offer an Intake Manifold Bolt Kit #8504 that includes small-head silver Cadmium-plated bolts and matching hardened washers). Apply a small amount of RTV silicone to the threads of the eight inner bolts (1,2,3,4,5,7,9, & 11) (See Figure 1) . This will prevent oil weepage, as generally these are not blind holes in the cylinder head. 6. Torque all of the manifold bolts in two steps by the sequence shown in Figure 1 to 25 ft/lbs. INTAKE MANIFOLD TOP 1. Apply Edelbrock Gasgacinch sealant P/N 9300 to the gasket mating surface and install the gasket and manifold top. 2. Install and tighten the supplied hold down bolts using a liquid thread-locking compound on the bolt threads. As an extra safety precaution, we suggest you drill a small safety wire hole in the head of each bolt and safety wire them together. Edelbrock Corporation expressly disclaims any liability for any and all consequential damages.